TECHNICAL DATA SHEET
Recovery 95% ASTM D412 Shore A Hardness Min 60 ASTM C661 Adhesion in Peel after Water Immersion Pass ASTM C836 Water Vapor Permeance Procedure A (Dry Cup) Procedure B (Inverted Wet Cup) 0.05 perms (3.09 ng/Pa m2 sec) 0.36 perms (20.6 ng/Pa m 2 sec) ASTM E96 Hydrostatic Pressure Resistance >0.69 MPa (100 psi) ASTM D5385
Download TECHNICAL DATA SHEET
Information
Domain:
Source:
Link to this page:
Documents from same domain
HE784 - AQUA-BLOC® WB - henry.com
henry.comLimited Warranty We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product - such as weather, workmanship, equipment utilized and prior condition of the substrate - are
TECHNICAL DATA SHEET - Henry
henry.comImpermeable to air, moisture vapor and water Compatible with Henry® Air-Bloc fluid applied air barriers Self-gasketing when penetrated and under compression with self-tapping screws Usage Blueskin SA is designed for use as a self-adhered air, vapor and water resistive barrier. It can also be used as a transition sheet
Henry Blueskin VP160 Air Barrier System Installation Manual
henry.com3 1. Introduction This installation manual includes materials and installation procedures for Henry® Blueskin® VP160 Self-Adhered Water Resistive Air Barrier system. Blueskin® VP160 meets the current IBC and IECC air barrier requirements for a water resistive barrier (WRB) as referenced in ICC ESR-2975.
TECHNICAL DATA SHEET - Henry
henry.comAir Permeance - Material @1.57psf (75Pa) 0.0001 cfm/ft² (0.0005 L/[sec-m²]) ASTM E2178 Air Leakage - Assembly Pass ASTM E2357 Elongation 250% ASTM D412 Tensile Strength 140 psi (965 kPa) ASTM D412 Flame Spread Index 10, Class A ASTM E84 Smoke Developed 15, Class A ASTM E84 Fire Testing Complies with NFPA 285 in various wall
Henry 925 BES Sealant
henry.comHenry® 925 BES Sealant is a premium, moisture cure sealant for construction joints subject to dynamic joint movement. This one-part, low odor, moisture cure product provides excellent weathering resistance, flexibility, very low VOC, through use of a silyl-terminated polyether (STPE) polymer. Upon curing, it is paintable with latex based paints.
TECHNICAL DATA SHEET - Henry
henry.comcast-in-place concrete, concrete block, steel, aluminum and galvanized metal. Strike masonry joints full-flush. Concrete surfaces must be smooth and without large voids, spalled areas or sharp protrusions. Concrete must be cured a minimum of 14 days. Curing
Air-Bloc All Weather STPE
henry.comHenry® Air-Bloc All-Weather STPE is a low VOC, UV and fire-resistant fluid applied, elastomeric membrane designed to provide a vapor permeable, water resistive air barrier when applied to above-grade wall assemblies. It is single-component, moisture cure
TECHNICAL DATA SHEET Blueskin WP200 - Henry
henry.comREVISION: 02/27/17 Henry Company 999 N. Sepulveda, Ste 800, El Segundo CA 90245-2754 Technical Services- Phone (800) 486-1278 – Email: techservices@henry.com www.henry.com Blueskin WP 200 Self-Adhesive Waterproofing Membrane Uses Blueskin WP200 is designed for use as a self-adhered s heet waterproofing membrane in above or below grade applications.
Air & Water Barrier Membrane - Henry
henry.comConcrete . ASTM C836 load suction pressure-Low Temperature Flexibility and Crack Bridging @ –20°C . ASTM C836 -Aging-Long Term Flexibility . CGSB 71 -GP-24M -Nail Sealability . ASTM D1970 --Resistance to Mold, Mildew & Fungal growth . ASTM D5590 . ASTM E84-VOC Content . Gray . 60% . 10.8 lbs/gal (1.3 kg/l) 2 Hours to touch dry . 24 Hours to ...
WATERPROOFING SYSTEMS - Henry
henry.comSecondary Containment Structures • Tunnels • Underground ... Drainage & Irrigation Channels • Potable Water Reserves • Seals Embedded Steel, PVC or HDPE Pipe Penetrations HENRY DRAINAGE COMPOSITES: A BETTER ENGINEERED SOLUTION FOR MANAGING THE FLOW OF WATER ... highway drainage systems.
Related documents
Control Valve Sizing - CTi Controltech
cti-ct.comat or below vapor pressure. The result is a two phase mixture (vapor and liquid) at the valve outlet and in the downstream piping. Velocity of this two phase flow is usually very high and results in the possibility for erosion of the valve and piping components. Choked Flow Choked flow occurs in gases and vapors when the fluid
Designing a Boiler Chimney Heat Recovery System Against ...
mechanical.uonbi.ac.kev LIST OF SYMBOLS AND ABREVIATIONS. A a: Air side total surface area. A c: Exchanger minimum free flow area. A fr: Heat exchanger frontal area. A g: Gas side total surface area. A: Surface area of the heat exchanger surfaces. C p: Specific heat capacity of air at constant pressure. F: Correction factor for the heat exchanger. H 1: Height of the exchanger core.
Crude Fat Methods Considerations - AAFCO
www.aafco.org1 Crude Fat Methods – Considerations ... (time, temperature, particle size, ratio of solvent to test portion, etc.) and is not specific for the extraction of lipid material. Lipids are commonly defined as a broad category of non-polar molecules that are ... solvent system usually allows for more complete recovery of the solvent if desired
POLYNUCLEAR AROMATIC HYDROCARBONS by HPLC 5506
www.cdc.gov11. Recovery and desorption efficiency. a. Determine recovery (R) from filters and desorption efficiency (DE) from sorbent tubes at least once for each lot of filters and sorbent tubes used in the range of interest. (1) Filters. Using a microliter syringe or a …
MOLYKOTE(R) 111 COMPOUND - MSC Industrial Direct
www1.mscdirect.comOct 14, 2017 · equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC. OSHA No component of this product present at levels greater than or equal to 0.1% is on OSHA’s list of regulated carcinogens. NTP No ingredient of this product present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen
AP-42 Section 5.2: Transportation And Marketing Of ...
www3.epa.govVapor recovery efficiency is 95 percent Vapor collection efficiency is 98.7 percent (NSPS-level annual leak test) Loading loss equation - where: S = saturation factor (see Table 5.2-1) - 1.00 P = true vapor pressure of gasoline = 6.6 psia M = molecular weight of gasoline vapors = 66 T = temperature of gasoline = 540°R