TECHNICAL DATA SHEET: THREADED ROD
Aug 22, 2019 · 3/8 - 16 0.29 610 540 1/2 - 13 0.54 1130 1010 5/8 - 11 0.83 1810 1610 3/4 - 10 1.25 2710 2420 7/8 - 9 1.70 3770 3360 1 - 8 2.23 4960 4420 ... *As of August 2007, Grade C has been replaced by specification F1554 Grade 36. We will continue supplying grade C, if required for the project. GRADES. TECHNICAL DATA SHEET: THREADED RD
Download TECHNICAL DATA SHEET: THREADED ROD
Information
Domain:
Source:
Link to this page:
Related documents
Standard Specification for Anchor Bolts, Steel, 36, 55, and ...
www.3ppars.com6.5.3 The maximum hot bending temperature for heat-treated anchor bolts shall be less than 700°F for Grade 55 and less than 1000°F for Grade 105.Anchor bolts shall be allowed to air cool after bending. TABLE 1 Chemical Composition Requirements Grade 36 Grades 55 and 105 Element Diameters up to 3⁄ 4, incl Over 7⁄ 8 to 4, incl All Diameters ...
A review of the concepts behind anchoring columns, as ...
www.aisc.orgASTM A572 Grade 50 material may be more appropri-ate for economy. ASTM F1554 is the usual material for anchor rods, and Grade 36 has the widest availability. Grades 55 and 105 are used when there is uplift or large moments. It is good practice to verify the availability of base plate and anchor rod materials with the structural
Anchor Rods - AISC
www.aisc.orgricator, ASTM F1554 grade 36 anchor rods may be specified as a fail-safe option. 3 Specifying many different anchor rod set-tings Specifying a different anchor rod setting pat-tern and base plate for every column size will end up leading to complications. Reduce the variety of anchor rod settings Specify one anchor rod setting and base plate
Suggested Assembly Torque Values - CopperState
www.copperstate.comColor codes for painting the ends of F1554 Graded rods: Grade 36 = Blue, Grade 55 = Yellow , Grade 105 = Red. All Thread Rod & All Thread Stud Materials When galvanizing high strength studs such as B7 & F1554-105, caution should be used as there is a risk of hydrogen embrittlement. Consult the design engineer and the galvanizer for your ...
Mechanical Properties of Externally Threaded Fasteners
www.fastenal.comAug 25, 2009 · ASTM F1554 Anchor Bolts, Steel Grade 36 Low or medium carbon steel 1/4 - 4-in 58,000(min) 80,000 (max) 36,000 ASTM A563 Grade A (hex up to 1-1/2 & Heavy Hex 1-1/2 and over) Notes 1, 2, 3 ASTM F835 Socket Button & Flat Countersunk Head Cap Screw Medium carbon alloy steel: quenched &
FASTENER REFERENCE GUIDE
www.fastenal.comASTM F1554 Anchor Bolts, Grade 36 Low or medium carbon steel 1/4 - 4 – ... Grade 2 requirements for sizes 1/4 through 3/4 in apply only to bolts and screws 6 in. and shorter in lengths. For bolts and screws longer than 6 in. Grade 1 requirements shall apply. 307A 307B
HILTI TECHNICAL BULLETIN
www.hilti.comMar 04, 2018 · )n ≤ 1, where n=5/3 for 3/8- and 1/2-inch diameters (No. 3 and No. 4 rebar) and n=1 for 5/8 and 3/4-inch diameter or No. 5 and No. 6 rebar. 9 The critical spacing, s cr, is the smallest anchor spacing where full load values may be used. The minimum spacing, s min, is the minimum anchor spacing for which values are