technical datasheet - MicroChemicals
AZ P4000 Series photoresists may be thermally cured after develop to form stable dielectric isolators. The dielectric properties are cure temperature dependent as shown in the table below.
Download technical datasheet - MicroChemicals
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet Technisches Datenblatt
www.microchemicals.comTechnical Data Sheet Technisches Datenblatt. Development . Immersion Immerse for approximately 60 seconds in either high-contrast or high-speed AZ Developer
Technical Data Sheet Technisches Datenblatt
www.microchemicals.comTechnical Data Sheet Technisches Datenblatt. HANDLING ADVISES . Consult the Material Safety Data Sheets provided by us or your local agent!. This AZ Photoresists are made up with our patented safer solvent PGMEA.
AZ nLOF 20xx Negative Resist - MicroChemicals
www.microchemicals.comMicroChemicals GmbH Ulm – www.microchemicals.com - tech@microchemicals.com AZ ®® nLOF 20xx Negative Resist ... complement Information for Processing revised 2005-11 …
General Purpose Developer - MicroChemicals
www.microchemicals.comDescription AZ 351B Developer is a general purpose developer for use with almost any positive AZ Photoresist. It was designed to achieve utmost contrast and best wall profile.
Post Exposure Bake (PEB) - microchemicals.com
www.microchemicals.comAZ® 726 MIF is 2.38 % TMAH- (TetraMethylAmmoniumHydroxide) in water, with additional surfactants for rapid and uniform wetting of the substrate (e. g. for puddle development) AZ® 826 MIF is 2.38 % TMAH- (TetraMethylAmmoniumHydroxide) in water, with additional surfactants for rapid and uniform wetting of the substrate (e. g. for puddle development) and other additives for the removal of ...
ELECTRO-PLATING: BASICS - MicroChemicals
www.microchemicals.comELECTRO-PLATING: BASICS The following section would like to explain the physical and chemical basis for electroplating to the extent as it is useful for understanding the following chapters. The Metal Potential A Metal in Aqueous Solution If a metal is dipped in an aqueous solution (a salt solution, a diluted acid, or only water), some of the
Silicon Ingot Production - MicroChemicals
www.microchemicals.comFirst, poly-crystalline silicon (e.g. from the Siemens-pro-cess) optionally together with dopants are melted in a quartz crucible at a temperature > 1400°C in an inert Fig. 3: The deposition of poly-crystalline silicon from the gas-eous phase of highly purifi ed trichlorosilane and hydrogen in the so-called Siemens process Cha m b e r (cool ...
Silicon Wafer Production and Specifications - MicroChemicals
www.microchemicals.comost any application. How ever, the special properties of each resist fami y makes them specially suited for AZ certain fields of application. 2 Resi s t f i lm thi c kness achievable and TI processable with stan d ard equ i pm e nt u n der standa r d conditions. So m e resist s can be dilut e d for lower fi lm thickne s ses; with additional ...
Wet-chemical etching of silicon and SiO2
www.microchemicals.comchromium are used, which in turn can be structured using photoresist masks. Fig. 120: The concentration and temperature-dependent selectivity of the etching rate of (100) - Si and SiO 2
WET-CHEMICAL ETCHING OF METALS
www.microchemicals.comThe chromium nitrate, which during the etching process forms a dark, constantly new formation on the chromium layer, is very soluble in water and thus in the chromate etchants. Compatibility and Selectivity All of our photoresists are suffi ciently stable in ceric ammonium nitrate and perchloric acid-based etching
Related documents
Agilent Basics of Measuring the Dielectric Properties of ...
academy.cba.mit.edudielectric properties. Agilent Technologies Inc. offers a variety of instruments, fixtures, and software to measure the dielectric properties of materials. Agilent measure-ment instruments, such as network analyzers, LCR meters, and impedance analyzers range in frequency up to 325 GHz. Fixtures to hold the material
Corning® Gorilla® Glass 5
www.corning.comOptical Refractive Index* (590 nm) Core Gla s 1.50 CompressionLayer 1.51 to-elas ic cons ant 30.2 nm /cm MPa Transmission @ 0.8 mm thickness ≥ 90.5% 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 100 90 80 70 60 50 40 30 20 10 0 Wavelength (nm) % Transmittance Corning® Gorilla® Glass 5 Transmittance ≥ 90.5% Wavelength 380 2000
TYPICAL PROPERTIES of ACRYLIC PMMA - iPolymer
www.ipolymer.comD149 Dielectric Strength (V/mil) short time, 1/8" thick 400 D150 Dielectric Constant at 60 Hz 4.0 D150 Dissipation Factor at 60 Hz 0.05 OPTICAL - Light Transmission, minimum (%) 92 - Refractive Index 1.48-1.50 NOTE: The information contained herein are typical values intended for reference and comparison purposes only.
Module 6: Attenuation in Optical Fibers
opti500.cian-erc.orgcomplex dielectric function for the material which, in turn, gives rise to the complex refractive index at optical frequencies. More specifically, the propagation of light within a material can be described in terms of a complex refractive index (n *): n* =n(ω) + iκ(ω) (Equation 3.4)