TEST METHOD STANDARD ELECTRONIC AND ELECTRICAL …
6.1 Intended use. This test method standard specifies uniform procedures for the environmental, physical, and electrical testing of electronic and electrical component piec e parts. It is intended as a reference document for test requirements called out in military component specifications and when specified, in other procurement
Download TEST METHOD STANDARD ELECTRONIC AND ELECTRICAL …
Information
Domain:
Source:
Link to this page:
Documents from same domain
Photonic Integrated Circuit (PIC) Device Structures ...
nepp.nasa.govand construct electronic devices onto a single CMOS chip. Photonic integrated circuits (PICs) exist as the optical analog to integrated circuits; however, in place of transistors, PICs consist of numerous scaled
Assessing and Mitigating Radiation Effects in Xilinx FPGAs
nepp.nasa.govThis research was carried out at the Jet Propulsion Laboratory, California Institute of Technology, and was sponsored by the National Aeronautics and Space Administration Electronic Parts and Packaging (NEPP) Program.
Radiation Effects Assessment of MRAM Devices - NASA
nepp.nasa.govRadiation Effects Assessment of MRAM Devices Mohamed Elghefari Jet Propulsion Laboratory Pasadena, California Steve McClure Jet Propulsion Laboratory Pasadena, California Jet Propulsion Laboratory California Institute of Technology Pasadena, California JPL Publication 08-19 5/08 .
S-311-S-819 - Resistor, Fixed, Foil (Managanin) Power ...
nepp.nasa.govSurface Mount CODE 311 SUPERVISORY APPROV~: I I I Ronald Chinnapongse ~~ Ir~7 ... fOil, precIsion, current sensing resistor In a surface mounted package. This 4-terminal (two power J-shaped and two sense gull-wing-shaped) resistor is intended for use in ... Marking shall in no way interfere with or obscure any of the original manufacturer's ...
S-311-S-821 - Resistor, Fixed, Foil (Manganin), Chip ...
nepp.nasa.govfOil, precIsion, current sensing resistor In a surface mounted package. This chip ... Marking shall in no way interfere with or obscure any of the original manufacturer's marking. b. The number of lines shall be at discretion of the test facility or laboratory. ... Foil (Manganin), Chip, Power, Current Sensing, Surface Mount ...
Mechanical Properties and Microstructure Investigation Of ...
nepp.nasa.govSn-Ag-Cu alloy is considered the preferred substitute for tin-lead solder in reflow applications due to its relatively low melting temperature, and superior mechanical properties and solderability compared with other lead free solders.
32 IEEE TRANSACTIONS ON ELECTRONICS PACKAGING ...
nepp.nasa.govCOUREY et al.: TIN WHISKER ELECTRICAL SHORT CIRCUIT CHARACTERISTICS—PART I 33 considers the following factors: conductor spacing, lead con-tent in tin plating, process by which the tin was deposited, tin thickness, materialdirectly beneaththetin, substrate controlling
IEEE TRANSACTIONS ON ELECTRONICS PACKAGING …
nepp.nasa.govCOUREY et al.: TIN WHISKER ELECTRICAL SHORT CIRCUIT CHARACTERISTICS—PART II 43 Fig. 4. Schematic diagram for the tin whisker test station instrumentation. Re-produced from [4]. Fig. 5. Tin whisker test station probing area close up.
Temperature Dependent Dielectric Properties of ...
nepp.nasa.govTemperature Dependent Dielectric Properties of Polycrystalline 96%Al 2O 3 Liang-Yu Chen1 and Gary W. Hunter2 1Ohio Aerospace Institute/NASA Glenn Research Center at Lewis Field, Cleveland, OH 44135 2NASA Glenn Research Center at Lewis Field, Cleveland, OH 44135 Abstract Polycrystalline Al 2O 3 substrates have been proposed and tested for high ...
Space Grade Requirements for Electrical Connectors
nepp.nasa.govGSFC-S-311-P-10, Subminiature, electrical and coaxial contact, electrical, connector. Military Specifications and Standards MIL-STD-1344 Test Methods for Electrical Connectors MIL-STD-202: Test Methods for Electronic and Electrical Component parts MIL-C-5015, Circular, threaded, AN type, electrical, connector.
Related documents
Manual-Ranging Digital Meter - Klein Tools
data.kleintools.com1. Insert RED test lead into V˚ jack 5 and BLACK test lead into COM jack 4, and rotate function selector switch 2 to the setting. 2. Remove power from circuit. 3. Test for continuity by connecting conductor or circuit with test leads. If resistance is measured less than 100Ω, an audible signal will sound and display will show a resistance value
Scotch Super 33+ Vinyl Electrical Tape
multimedia.3m.comIn accordance with Canadian Electrical Code, Part 1 3. Not for specification. Values are typical, not to be considered minimum or maximum. 4. ASTM D1000 Test Method - properties measured at room temperature 73°F (23°C) unless otherwise stated Product Description Scotch® Super 33+ Vinyl Electrical Tape is a 7-mil thick, premium grade all ...
Managing Electrical Risks in the Workplace - SafeWork NSW
www.safework.nsw.gov.auwork that is not electrical work carried out on telephone, communication and data systems work carried out by or on behalf of an electricity supply authority on the electrical equipment controlled or operated by the authority to generate, transform, transmit or supply electricity, and
“Electrical Safety in the Workplace”
www.osha.gov“Electrical Safety in the Workplace” 2 Course Goal – The aim of this program is to provide comprehensive on-site training to high-risk workers (i.e. skilled trades and maintenance workers) and management on the requirements of Sub Part S, and the prevention
Test instruments for electrical installations: Accuracy ...
www.electricalsafetyfirst.org.uk©The Electrical Safety Council page 3 Test instruments for electrical installations: Accuracy and consistency. SCOPE This guidance applies to test instruments intended for use ... but individual calibration data is not issued. Following the confirmation of initial accuracy, it is
PCI Express 4.0 Electrical Previews
pcisig.comWaveform-based test with reference equalizer application in post-processing was chosen as the only option to asses overall Tx interoperability of channel plus silicon CEM Tx test is an eye test @ BER ≤10-12 after applying the reference equalizer No jitter decomposition beyond Rj/Dj due to end of channel reference point
Engineering Data for Copper and Aluminum Conductor ...
www.okonite.comEngineering Data for Copper and Aluminum Conductor Electrical Cables ... TABLE 8 - 1 High Voltage Field Acceptance Test 52 TABLE 8 - 2 High Voltage Maintenance Test 53 TABLE 8 - 3 Frequency of Proof Testing 53 SECTION 9 Miscellaneous Information TABLE 9 - 1 Jacket Materials Selection Chart 55
VLF Tan Delta And Withstand Testing Of Electrical Power …
www.nrc.gov[2] Diagnostic Test - A field test made during the operating life of a cable system. It is intended to determine and locate degradation that may cause cable and accessory failure. [3] Device Under Test (DUT) - The electrical apparatus such as the cable being tested. [4] Extruded Cables - Cables such as Butyl Rubber, EPR, XLPE, TR-XLPE, PE