TEST METHOD STANDARD ELECTRONIC AND ELECTRICAL …
ANSI/J-STD-002 - Solderability Tests For Component Leads, Terminations, Lugs, Terminals and Wires ANSI/J-STD-004 - Requirements For Soldering Fluxes ANSI/J-STD-005 - Requirements For Soldering Pastes ANSI/J-STD-006 - Requirements For Electronic Grade Solder Alloys and Fluxed and Non-Fluxed Solid
Download TEST METHOD STANDARD ELECTRONIC AND ELECTRICAL …
Information
Domain:
Source:
Link to this page:
Documents from same domain
Photonic Integrated Circuit (PIC) Device Structures ...
nepp.nasa.govand construct electronic devices onto a single CMOS chip. Photonic integrated circuits (PICs) exist as the optical analog to integrated circuits; however, in place of transistors, PICs consist of numerous scaled
Assessing and Mitigating Radiation Effects in Xilinx FPGAs
nepp.nasa.govThis research was carried out at the Jet Propulsion Laboratory, California Institute of Technology, and was sponsored by the National Aeronautics and Space Administration Electronic Parts and Packaging (NEPP) Program.
Radiation Effects Assessment of MRAM Devices - NASA
nepp.nasa.govRadiation Effects Assessment of MRAM Devices Mohamed Elghefari Jet Propulsion Laboratory Pasadena, California Steve McClure Jet Propulsion Laboratory Pasadena, California Jet Propulsion Laboratory California Institute of Technology Pasadena, California JPL Publication 08-19 5/08 .
S-311-S-819 - Resistor, Fixed, Foil (Managanin) Power ...
nepp.nasa.govSurface Mount CODE 311 SUPERVISORY APPROV~: I I I Ronald Chinnapongse ~~ Ir~7 ... fOil, precIsion, current sensing resistor In a surface mounted package. This 4-terminal (two power J-shaped and two sense gull-wing-shaped) resistor is intended for use in ... Marking shall in no way interfere with or obscure any of the original manufacturer's ...
S-311-S-821 - Resistor, Fixed, Foil (Manganin), Chip ...
nepp.nasa.govfOil, precIsion, current sensing resistor In a surface mounted package. This chip ... Marking shall in no way interfere with or obscure any of the original manufacturer's marking. b. The number of lines shall be at discretion of the test facility or laboratory. ... Foil (Manganin), Chip, Power, Current Sensing, Surface Mount ...
Mechanical Properties and Microstructure Investigation Of ...
nepp.nasa.govSn-Ag-Cu alloy is considered the preferred substitute for tin-lead solder in reflow applications due to its relatively low melting temperature, and superior mechanical properties and solderability compared with other lead free solders.
32 IEEE TRANSACTIONS ON ELECTRONICS PACKAGING ...
nepp.nasa.govCOUREY et al.: TIN WHISKER ELECTRICAL SHORT CIRCUIT CHARACTERISTICS—PART I 33 considers the following factors: conductor spacing, lead con-tent in tin plating, process by which the tin was deposited, tin thickness, materialdirectly beneaththetin, substrate controlling
IEEE TRANSACTIONS ON ELECTRONICS PACKAGING …
nepp.nasa.govCOUREY et al.: TIN WHISKER ELECTRICAL SHORT CIRCUIT CHARACTERISTICS—PART II 43 Fig. 4. Schematic diagram for the tin whisker test station instrumentation. Re-produced from [4]. Fig. 5. Tin whisker test station probing area close up.
Temperature Dependent Dielectric Properties of ...
nepp.nasa.govTemperature Dependent Dielectric Properties of Polycrystalline 96%Al 2O 3 Liang-Yu Chen1 and Gary W. Hunter2 1Ohio Aerospace Institute/NASA Glenn Research Center at Lewis Field, Cleveland, OH 44135 2NASA Glenn Research Center at Lewis Field, Cleveland, OH 44135 Abstract Polycrystalline Al 2O 3 substrates have been proposed and tested for high ...
Space Grade Requirements for Electrical Connectors
nepp.nasa.govGSFC-S-311-P-10, Subminiature, electrical and coaxial contact, electrical, connector. Military Specifications and Standards MIL-STD-1344 Test Methods for Electrical Connectors MIL-STD-202: Test Methods for Electronic and Electrical Component parts MIL-C-5015, Circular, threaded, AN type, electrical, connector.
Related documents
AEC-Q100, Q101, Q200 - ictest8.com
www.ictest8.comJ-STD-002 Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires. J-STD-020 Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices JESD22-A113 Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing