TEST METHOD STANDARD ELECTRONIC AND ELECTRICAL …
This test method standard specifies uniform procedures for the environmental, physical, and electrical testing of electronic and electrical component piec e parts. It is intended as a reference document for test requirements called out in military component specifications and when specified, in other procurement
Download TEST METHOD STANDARD ELECTRONIC AND ELECTRICAL …
Information
Domain:
Source:
Link to this page:
Documents from same domain
Photonic Integrated Circuit (PIC) Device Structures ...
nepp.nasa.govand construct electronic devices onto a single CMOS chip. Photonic integrated circuits (PICs) exist as the optical analog to integrated circuits; however, in place of transistors, PICs consist of numerous scaled
Assessing and Mitigating Radiation Effects in Xilinx FPGAs
nepp.nasa.govThis research was carried out at the Jet Propulsion Laboratory, California Institute of Technology, and was sponsored by the National Aeronautics and Space Administration Electronic Parts and Packaging (NEPP) Program.
Radiation Effects Assessment of MRAM Devices - NASA
nepp.nasa.govRadiation Effects Assessment of MRAM Devices Mohamed Elghefari Jet Propulsion Laboratory Pasadena, California Steve McClure Jet Propulsion Laboratory Pasadena, California Jet Propulsion Laboratory California Institute of Technology Pasadena, California JPL Publication 08-19 5/08 .
S-311-S-819 - Resistor, Fixed, Foil (Managanin) Power ...
nepp.nasa.govSurface Mount CODE 311 SUPERVISORY APPROV~: I I I Ronald Chinnapongse ~~ Ir~7 ... fOil, precIsion, current sensing resistor In a surface mounted package. This 4-terminal (two power J-shaped and two sense gull-wing-shaped) resistor is intended for use in ... Marking shall in no way interfere with or obscure any of the original manufacturer's ...
S-311-S-821 - Resistor, Fixed, Foil (Manganin), Chip ...
nepp.nasa.govfOil, precIsion, current sensing resistor In a surface mounted package. This chip ... Marking shall in no way interfere with or obscure any of the original manufacturer's marking. b. The number of lines shall be at discretion of the test facility or laboratory. ... Foil (Manganin), Chip, Power, Current Sensing, Surface Mount ...
Mechanical Properties and Microstructure Investigation Of ...
nepp.nasa.govSn-Ag-Cu alloy is considered the preferred substitute for tin-lead solder in reflow applications due to its relatively low melting temperature, and superior mechanical properties and solderability compared with other lead free solders.
32 IEEE TRANSACTIONS ON ELECTRONICS PACKAGING ...
nepp.nasa.govCOUREY et al.: TIN WHISKER ELECTRICAL SHORT CIRCUIT CHARACTERISTICS—PART I 33 considers the following factors: conductor spacing, lead con-tent in tin plating, process by which the tin was deposited, tin thickness, materialdirectly beneaththetin, substrate controlling
IEEE TRANSACTIONS ON ELECTRONICS PACKAGING …
nepp.nasa.govCOUREY et al.: TIN WHISKER ELECTRICAL SHORT CIRCUIT CHARACTERISTICS—PART II 43 Fig. 4. Schematic diagram for the tin whisker test station instrumentation. Re-produced from [4]. Fig. 5. Tin whisker test station probing area close up.
Temperature Dependent Dielectric Properties of ...
nepp.nasa.govTemperature Dependent Dielectric Properties of Polycrystalline 96%Al 2O 3 Liang-Yu Chen1 and Gary W. Hunter2 1Ohio Aerospace Institute/NASA Glenn Research Center at Lewis Field, Cleveland, OH 44135 2NASA Glenn Research Center at Lewis Field, Cleveland, OH 44135 Abstract Polycrystalline Al 2O 3 substrates have been proposed and tested for high ...
Space Grade Requirements for Electrical Connectors
nepp.nasa.govGSFC-S-311-P-10, Subminiature, electrical and coaxial contact, electrical, connector. Military Specifications and Standards MIL-STD-1344 Test Methods for Electrical Connectors MIL-STD-202: Test Methods for Electronic and Electrical Component parts MIL-C-5015, Circular, threaded, AN type, electrical, connector.
Related documents
Standard Test Methods for DC Resistance or Conductance of ...
www-eng.lbl.gov1.2 These test methods are not suitable for use in measuring the electrical resistance/conductance of moderately conductive materials. Use Test Method D4496 to evaluate such materials. 1.3 This standard describes several general alternative methodologies for measuring resistance (or conductance).
IS 2386-3 (1963): Methods of test for aggregates for ...
www.iitk.ac.inIndian Standard METHODS OF TEST FOR AGGREGATES FOR CONCRETE PART III SPECIFIC GRAVITY, DENSITY, VOIDS, ABSORPTION AND BULKING 0. FOREWORD 0.1 This Indian Standard ( Part III ) was adopted by the Indian Standards Institution on 22 August 1963, after the draft finalized by
MIL-STD-883E, Test Method Standard for Microcircuits
scipp.ucsc.edugeographic or outer space location, since it is known that the only true test for operation in a specific application and location is an actual service test under the same conditions. b. To describe in one standard all of the test methods of a similar character which now appear in the various joint-services
Standard Test Method for Tensile Properties of Plastics1
www.dept.aoe.vt.eduE132 Test Method for Poisson’s Ratio at Room Temperature E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method 2.2 ISO Standard:4 ISO 527-1 Determination of Tensile Properties 3. Terminology 3.1 Definitions—Definitions of terms applying to this test method appear in Terminology D883 and Annex A2. 4.
A5TM D 2974-87 Standard Test Methods for Moisture, Ash ...
gsrpdf.lib.msu.edu9.5 This method should be used for all geo-technical and general classification purposes. 10.Method D 10.1 Determine the mass of acovered high-silica or porcelain dish. 10.2 Place a part of or all of the oven-dried test specimen from amoisture determination inthedish and determine the mass ofthedish and specimen.
Standard Test Method for Sieve Analysis of Fine and Coarse ...
kashanu.ac.irStandard Test Method for Sieve Analysis of Fine and Coarse Aggregates1 This standard is issued under the fixed designation C 136; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
ASTM E 84 Standard test method for surface burning ...
www.ahfc.usStandard test method for surface burning characteristics of of building materials. The flame spread Index and Smoke Developed Index values obtained by the ASTM E 84 test are used by code officials and regulatory agencies in the acceptance of interior finish materials for various applications. The most widely accepted classification system is
STANDARD TEST METHODS - Performance Products
www.cffaperformanceproducts.orgReference: ASTM D3389– Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader) Apparatus: Rotary Platform Double Head Abraser* To determine the abrasion resistance of a chemical coated fabric or film, one specimen of each sample shall be cut in a 4-1/8" circle and mounted on a S-16 Specimen Plate*.