The Codes below are for several different models.
Connect a known good potentiometer to control board socket and set sprayer ON and control knob to ½ turn clockwise. If ok, replace pot. Replace control board if sprayer still does not run. But first, verify transducer and connections are ok. See next page. OR Short center pin of socket to each outer pin. Install new potentiometer if sprayer runs.
Download The Codes below are for several different models.
Information
Domain:
Source:
Link to this page:
Documents from same domain
INSTRUCTIONS--PARTS LIST 309272C AirAtomizerKit
wwwd.graco.comINSTRUCTIONS--PARTS LIST 309272C Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. AirAtomizerKit
Double Diaphragm Pumps Concept and Theory - Graco Inc.
wwwd.graco.comDouble Diaphragm Pump Double Diaphragm Pumps use compressed air as the power source. They are frequently used for fluid transfer, low pressure spray, and …
308479AB Husky 1040 Air-Operated Diaphragm Pumps, …
wwwd.graco.coma. Install an air regulator (C) and gauge to control the fluid pressure. The fluid outlet pressure will be the same as the setting of the air regulator. b. Locate one bleed-type master air valve (B) close to the pump and use it to relieve trapped air. See the WARNING above. Locate the other master air valve (E) upstream from all air
Atomization Concept and Theory - Graco
wwwd.graco.comUltrasonic atomization relies on an electromechanical device that vibrates at a very high frequency. Fluid passes over the vibrating surface and the vibration causes the fluid to break into droplets. Figure 11 shows an example of ultrasonic atomization technology. Applications of this technology include: Medical nebulizers for inhalation therapy
Related documents
Ranger 8 - Joe's Welding
www.joeswelding.biz2 Output Potentiometer T10812-112 1 XXXXXXXX 2A Potentiometer Spacer S18280 1 XXXXXXXX 2B Knob T10491-1 1 XXXXXXXX 2C “O” Ring (Not Shown) T13483-7 1 XXXXXXXX 3 Selector Switch and Mounting Assembly M17013 1 XXXXXXXX 3A Control Handle M16493 2 XXXXXXXX 3B Self-Tapping Screw S8025-78 2 XXXXXXXX 4 Arc Polarity Switch Assembly …
Cavitron Parts Reference - ProSites
c1-preview.prosites.comC2 Replacement Control Knob (Blue) 80502 A11 Replacement Rubber Foot 592051001 A12 Prophy-Jet Air Polishing Nozzle Insert (3 pack) 7760204 ... D2 Potentiometer Switch and Harness 81638 D3 Cover, Decorated 81624 D4 Molded Overlay & Label, Info Center 81627 D5 Screw, #4-24 x 1/2" Hi-Lo 586172002
Troubleshooting the Mini Lathe Variable Speed Drive
littlemachineshop.com2. If there are five terminals, turn the potentiometer shaft all the way counterclockwise. 3. If there are five terminals, check continuity between the two terminals on the back of the potentiometer. There should be continuity. 4. If there are five terminals, turn the potentiometer shaft clockwise about 10 or 15 degrees.
CONTROL SYSTEMS LAB Laboratory Manual
mjcollege.ac.inThe speed control knob should be always in the most anticlockwise position before switching on the equipment. 2. In order to increase the armature voltage, rotate the knob in the clockwise direction in a ... Take the input potentiometer to the starting position i.e. very near to the zero position. The output
3386 - 3/8 ˝ Square Trimpot Trimming Potentiometer
www.bourns.comn Available with a knob for finger adjust n Available with extended shaft n Available with cross-slot rotor n Top and side adjust types (F, P, H, W, X ... 3386 - 3/8 ˝ Square Trimpot® Trimming Potentiometer 3.05 ± .38 (.120 ± .015) Common Dimensions Top Adjust Models M,T 3386F 5.08
USER MANUAL - Strymon
www.strymon.netEach tone knob on a classic amplifier controls a potentiometer that interacts with the other components that make up the tone stack, creating a complex, interdependent frequency response. Our Matrix Modeling™ process captures all these subtleties, faithfully delivering the unique tonal qualities of each amp type.
Installation and Operation Manual for 4L60E, 4L65E, 4L70E ...
www.usshift.compotentiometer-style throttle position sensor (almost all three-terminal TP sensors). A DVOM or analog Ohmmeter is required. 1. Set the meter to resistance mode and set it to a scale that can read up to 10K or 20K Ohms (if it is not auto-ranging). Please keep in mind when setting up and reading the meter that "K" means thousands of Ohms.