3386 - 3/8 ˝ Square Trimpot Trimming Potentiometer
n Available with a knob for finger adjust n Available with extended shaft n Available with cross-slot rotor n Top and side adjust types (F, P, H, W, X ... 3386 - 3/8 ˝ Square Trimpot® Trimming Potentiometer 3.05 ± .38 (.120 ± .015) Common Dimensions Top Adjust Models M,T 3386F 5.08
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Designing a Low Power Flyback Power Supply - …
www.bourns.comDesigning a Low Power Flyback Power Supply Vf Primary Switch Voltage V X Secondary Winding Voltage Secondary Current Primary Current Switch ON V …
Switch, Power, Supply, Designing, Designing a low power flyback power supply, Flyback
Preventing Component Circuit Damage from …
www.bourns.comMultifuse® PTC Resettable Fuses White Paper Preventing Component Circuit Damage from Above Range Current with Reliable Overcurrent Protection Introduction As the ...
Form, With, Protection, Current, Component, Circuit, Preventing, Damage, Reliable, Preventing component circuit damage from, Current with reliable overcurrent protection, Overcurrent
Features *RoHS COMPLIANTVERSIONS AVAILABLE …
www.bourns.comFeatures n Multiturn / Cermet / Industrial / Sealed n 5 terminal styles n Tape and reel packaging available n Chevron seal design n Listed on the QPL for styleRJ24 per MIL-R-22097 andRJR24 per High-Rel
SMCJ Transient Voltage Suppressor Diode Series
www.bourns.comSMCJ Transient Voltage Suppressor Diode Series Rating & Characteristic Curves Pulse Derating Curve Maximum Non-Repetitive Surge …
Bourns Power Supply Overview Component Guide …
www.bourns.comBourns® Power Supply Component Guide SMPS ... fulfill ongoing technical demands. • Transformer Prototype service with quick turnaround
ChipGuard Model CGF0804TFH-R900-2L ESD/EMI …
www.bourns.comSpecifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
MF-RX/72 Series - PTC Resettable Fuses - Bourns
www.bourns.comMF-RX/72 SERIES, REV. O 03/17 Typical Time to Trip at 23 ˚C DIMENSIONS: MM (INCHES) Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
4600X Series - Thick Film Conformal SIPs
www.bourns.comSpecifi cations are subject to change without notice. Customers should verify actual device performance in their specifi c applications. 4600X Series - Thick Film Conformal SIPs
CRA2512 - High Power Current Sense Chip Resistor
www.bourns.comFeatures n Special alloy resistor n Power rating at 70 °C: 3 W n Inductance less than 5 nH n RoHS compliant* n AEC-Q200 qualified, automotive grade Applications n Power supplies n Stepper motor drives
TISP4xxxM3BJ Overvoltage Protector Series - Bourns
www.bourns.comNOVEMBER 1997 - REVISED MAY 2007 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.
Related documents
Ranger 8 - Joe's Welding
www.joeswelding.biz2 Output Potentiometer T10812-112 1 XXXXXXXX 2A Potentiometer Spacer S18280 1 XXXXXXXX 2B Knob T10491-1 1 XXXXXXXX 2C “O” Ring (Not Shown) T13483-7 1 XXXXXXXX 3 Selector Switch and Mounting Assembly M17013 1 XXXXXXXX 3A Control Handle M16493 2 XXXXXXXX 3B Self-Tapping Screw S8025-78 2 XXXXXXXX 4 Arc Polarity Switch Assembly …
The Codes below are for several different models.
wwwd.graco.comConnect a known good potentiometer to control board socket and set sprayer ON and control knob to ½ turn clockwise. If ok, replace pot. Replace control board if sprayer still does not run. But first, verify transducer and connections are ok. See next page. OR Short center pin of socket to each outer pin. Install new potentiometer if sprayer runs.
CONTROL SYSTEMS LAB Laboratory Manual
mjcollege.ac.inThe speed control knob should be always in the most anticlockwise position before switching on the equipment. 2. In order to increase the armature voltage, rotate the knob in the clockwise direction in a ... Take the input potentiometer to the starting position i.e. very near to the zero position. The output
Cavitron Parts Reference - ProSites
c1-preview.prosites.comC2 Replacement Control Knob (Blue) 80502 A11 Replacement Rubber Foot 592051001 A12 Prophy-Jet Air Polishing Nozzle Insert (3 pack) 7760204 ... D2 Potentiometer Switch and Harness 81638 D3 Cover, Decorated 81624 D4 Molded Overlay & Label, Info Center 81627 D5 Screw, #4-24 x 1/2" Hi-Lo 586172002
USER MANUAL - Strymon
www.strymon.netEach tone knob on a classic amplifier controls a potentiometer that interacts with the other components that make up the tone stack, creating a complex, interdependent frequency response. Our Matrix Modeling™ process captures all these subtleties, faithfully delivering the unique tonal qualities of each amp type.
Troubleshooting the Mini Lathe Variable Speed Drive
littlemachineshop.com2. If there are five terminals, turn the potentiometer shaft all the way counterclockwise. 3. If there are five terminals, check continuity between the two terminals on the back of the potentiometer. There should be continuity. 4. If there are five terminals, turn the potentiometer shaft clockwise about 10 or 15 degrees.
Troubleshooting, Variable, Mini, Lathe, Potentiometer, Troubleshooting the mini lathe variable
Installation and Operation Manual for 4L60E, 4L65E, 4L70E ...
www.usshift.compotentiometer-style throttle position sensor (almost all three-terminal TP sensors). A DVOM or analog Ohmmeter is required. 1. Set the meter to resistance mode and set it to a scale that can read up to 10K or 20K Ohms (if it is not auto-ranging). Please keep in mind when setting up and reading the meter that "K" means thousands of Ohms.