Thermocouple Selection Guide - RS Components
Thermometer Thermistor Sensor Thermoelement, two dissimilar metals/alloys Platinum-wire wound or flat-film resistor Ceramic (metal oxides) Accuracy (typical values) 0.5 to 5.0°C 0.1 to 1.0°C 0.1 to 1.5°C Long term Stability Variable, Prone to ageing Excellent Good Temperature range-200 to1750°C -200 to 650°C -100 to 300°C
Download Thermocouple Selection Guide - RS Components
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Advertisement
Documents from same domain
LOCTITE 243™
docs.rs-online.comTDS LOCTITE® 243™, August-2016 For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush Loctite Material SpecificationLMS LMS dated June-29, 2009.
Shelf Life for Loctite Products - RS Components
docs.rs-online.comThe shelf life period for Loctite® products is one year from date of shipment from Henkel facilities or as indicated by package labeling. For optimal storage, maintain product at a temperature between 8°C (46°F) to 21°C (70°F). Storage below 8°C (46°F) or greater than 28°C (82°F) can adversely affect product properties.
AC Industrial Electric Motors Data Sheet
docs.rs-online.comThe power factor usually being referred to as cos Ø. The power factor is usually between 0.7 and 0.9, however this may vary depending on the motor size and rating. If there are many motors in an installation they will consume a lot of reactive power and will therefore have a lower power factor. Power supply authorities sometimes require the
SIM868 Hardware Design V1.00-150516 - RS Components
docs.rs-online.comSIM868 is a quad-band GSM/GPRS module that works on frequencies GSM 850MHz, EGSM 900MHz, DCS 1800MHz and PCS 1900MHz. SIM868 features GPRS multi-slot class 12/class 10 (optional) and supports
APPLICATION MKS-L MKS-SC
docs.rs-online.comNote: (1) These tools are for prototype tooling or repair. (2) YC tool has two crimping sections (A and B). YRS tool has also two crimping sections by inverting upper dies. Be sure to check applicable wires before use. Since the dies are fixed, the crimping height cannot be adjusted. Therefore, some of the
APC Smart-UPS X-Series 2000/2200/3000 VA Operation Manual
docs.rs-online.comSmart-UPS X 2000/2200/3000 VA 1 Overview About the UPS The APC® by Schneider Electric Smart-UPS® X is a high performance uninterruptible power supply (UPS). It provides protection for electronic equipment from utility power blackouts, brownouts, sags,
Power, Smart, Supply, Uninterruptible power supply, Uninterruptible, Smart ups
Charger Instructions for Duracell High-Speed Chargers (ALL)
docs.rs-online.com5. The charger is capable of accepting 100-240 V AV 50/60 Hz and therefore, can be used overseas with a corresponding regional plug converter. 6. If battery is fully charged and then reinserted right away into the charger, the fault Red Blinking LED indicator may occur since the battery is already fully charged 7.
Programmable Logic Controllers Beginner´s Manual
docs.rs-online.comThe programmable logic controllers of the FX1S,FX1N,FX2N,FX2NC,FX3G,FX3GC,FX3GE, FX3S,FX3U and FX3UC series are only intended for the specific applications explicitly described in this manual. All parameters and settings specified in this manual must be observed. The products described have all been designed, manufactured, tested and docu-
PLATINUM RESISTANCE THERMOMETER (PRT)
docs.rs-online.comBuy this and more at rspro.com RS PRO Sensors - PRT Guide 3 COMPARISON OF SENSOR TYPES PLATINUM RESISTANCE THERMOMETER THERMOCOUPLE THERMISTOR Sensor Platinum-wire wound or flatfilm resistor Thermoelement, two dissimilar metals/alloys Ceramic (metal oxides) Accuracy (typical values) 0.1 to 1.0°C 0.5 to 5.0°C 0.1 to 1.5°C Long term …
Data sheet 6ES7131-6BH01-0BA0
docs.rs-online.comfor standard inputs — parameterizable Yes; 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms (in each case + delay of 30 to 500 µs, depending on line length)
Related documents
Vegetable Planting Guide - Texas A&M University
dallas-tx.tamu.eduA kitchen thermometer (probe type-temperature range is 0° to 220°) is the easiest, most available and least expensive product to use for this purpose. \'e etables from Trans lant a timum Soil Tern erature for Plantin Onions (45) Broccoli (50) Kohlrabi (50) Cabbage (55 Chinese Cabba e (55) Tomatoes (60) Pep ers (70) E.
Guide, Probes, Vegetable, Thermometer, Planting, Vegetable planting guide
Receiving Criteria Temperature - ServSafe
elearning.servsafe.comthermometer stem or probe directly into the thickest part of the food. The center is usually the thickest part. ROP food (MAP, vacuum-packed, and sous vide food) Insert the thermometer stem or probe between two packages. If the package allows, fold it around the thermometer stem or probe. Be careful not to puncture the package. Other packaged ...
Smoking Times & Temperatures Chart
www.smoking-meat.comhave a probe(s) that stays in the meat while it smokes. The probe is attached to a braided metal wire that runs through the door or an opening to the unit outside of the smoker. You can also use an instant-read digital thermometer such as the Thermapen Mk4 which reads in about 3 …
Braun ThermoScan Pro6000 Ear Thermometer, User Manual
www.hillrom.comThe thermometer collects information about the direction and depth of ear probe placement as it is placed into the ear canal and automatically incorporates this information into the temperature calculation. Incorporating information related to patient specific anatomy and exact ear probe placement in the ear canal increases the accuracy of the
INFRARED THERMOMETER MODEL DET-306 QUICK HELP …
dijf55il5e0d1.cloudfront.net• To clean probe window, using a clean cotton swab dipped in 70% alcohol, wipe the probe window 3 times. Wait 10 minutes before taking temperatures. • The thermometer is initially calibrated at the time of manufacture. If used properly, readjustments are not necessary.
Model, Probes, Infrared, Thermometer, Infrared thermometer model det 306
How to Calibrate a Bimetallic Stemmed Thermometer Using ...
www.servsafe.comPUT THE THERMOMETER STEM OR PROBE INTO THE ICE WATER. Make sure the sensing area is under water and not touching the sides of the container. Wait 30 seconds or until the reading stays steady. 2 ADJUST THE THERMOMETER SO IT READS 32°F (0°C). Hold the calibration nut securely with a wrench or other tool and