Vertical Installation Technical Specification
This specification also covers the installation of Linea Oblique Weatherboard on projects, which are subject to specific engineering design (SED) up to a wind pressure of 2.5kPa (ULS). 1.3 DETAILS Various typical Linea Oblique Weatherboard vertical construction details are provided in the Details section of this document.
Download Vertical Installation Technical Specification
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Specification - jameshardie.co.nz
www.jameshardie.co.nzLinea® Weatherboard Technical Specification April 2016 New Zealand 3 1 Application and scope 1.1 APPLICATION Linea® Weatherboard is …
Design Manual - jameshardie.co.nz
www.jameshardie.co.nzFire and Acoustic Design Manual August 2017 New Zealand 3 1 Introduction readers are familiar with the relevant James Hardie cladding and lining product literature.
Design Manual - James Hardie
www.jameshardie.co.nzFigure 1: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding Figure 2: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding 4 James Hardie Cladding Junction Details Design Manual November 2016 New Zealand Flexible underlay Linea™ Weatherboard Scriber 60 x 3.15mm jolt head
Fire & Acoustic - James Hardie
www.jameshardie.co.nz3.1 External Walls - Timber Frame 8 3.2 External Walls - Steel Frame 10 3.3 Parapet & Wing Walls ... S - StriaTM Cladding ... Refer to recommended safe working practices in each specific product technical specification or installation manual
CLD Structural Cavity Batten Technical Specification
www.jameshardie.co.nzThis specification covers the use of Titan Façade Panel on buildings, where the maximum wind pressure exerted on the building façade is up to 2.5kPa (ULS). This specification is intended for use by architects or designers/ specifier and installers who …
Design Manual - James Hardie
www.jameshardie.co.nzThe specifier or other party responsible for the project must run through a risk matrix analysis as per E2/AS1 to determine which construction method is applicable to install the external cladding on the project. The designer must also ensure that the bracing capacities published in this specification are appropriate for the intended application.
jameshardie.co.nz CLD Structural Cavity Batten
www.jameshardie.co.nzPortland cement, ground sand, cellulose fibre and water. The product is easily identified by the name 'Stria Cladding' printed on the back of the panels. CLD Structural Cavity Batten is manufactured using a low density fibre cement formulation. The basic composition is Portland cement, ground sand, cellulose fibre, water and proprietary additives.
Related documents
Sizing, Selection, and Installation of Pressure-relieving ...
ballots.api.orgSIZING, SELECTION, AND INSTALLATION OF PRESSURE-RELIEVING DEVICES IN REFINERIES 5 ASME B31.1, Power Piping ASME B31.31, Process Piping ASME PTC 25, Pressure Relief Devices 3 Terms and Definitions For the purposes of this document, the following definitions apply. Many of the terms and definitions are taken from
IS 2190 (2010): SELECTION, INSTALLATION AND …
law.resource.orgby the Fire Fighting Sectional Committee had been approved by the Civil Engineering Division Council. ... 2003 Specification for portable fire extinguishers, water type (gas cartridge) ... selection, installation, maintenance and testing of first-aid fire extinguishers. NOTE — The water, carbon dioxide ...
Guide Specification for Copper and Copper Alloy Building ...
www.copper.orgThis Guide Specification has been prepared for the use of professionals involved in the design, specification, installation and repair of copper and copper alloy piping systems in buildings. It has been compiled from information sources that the Copper Development Association Inc. (CDA) believes to be competent.
HVAC Quality Installation Specification (ACCA Standard 5)
www.energystar.govequipment selection, installation, and commissioning). Building owners / operators and residential consumers need to be informed of the links between comfort, humidity levels, utility bills, and indoor air quality with a proper HVAC system design and installation. Once aware, consumers will better
AS 2047-1999 Windows in buildings-Selection and installation
www.saiglobal.comPart 1: Specification for materials and performance and AS 2047.2—1996, Windows in buildings—Part 2: Construction, installation and maintenance. After allowing sufficient time for adjustment (nominally 12 months from publication), the superseded documents will be withdrawn.