Vertical Installation Technical Specification
design, the framing stiffness must be equivalent to, or more than, the stiffness requirements of NZS 3604. For specific design projects, the timber framing must be designed in accordance with the requirements of NZS 3603 and AS/NZS 1170. For …
Download Vertical Installation Technical Specification
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Specification - jameshardie.co.nz
www.jameshardie.co.nzLinea® Weatherboard Technical Specification April 2016 New Zealand 3 1 Application and scope 1.1 APPLICATION Linea® Weatherboard is …
Design Manual - jameshardie.co.nz
www.jameshardie.co.nzFire and Acoustic Design Manual August 2017 New Zealand 3 1 Introduction readers are familiar with the relevant James Hardie cladding and lining product literature.
Design Manual - James Hardie
www.jameshardie.co.nzFigure 1: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding Figure 2: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding 4 James Hardie Cladding Junction Details Design Manual November 2016 New Zealand Flexible underlay Linea™ Weatherboard Scriber 60 x 3.15mm jolt head
Fire & Acoustic - James Hardie
www.jameshardie.co.nz3.1 External Walls - Timber Frame 8 3.2 External Walls - Steel Frame 10 3.3 Parapet & Wing Walls ... S - StriaTM Cladding ... Refer to recommended safe working practices in each specific product technical specification or installation manual
CLD Structural Cavity Batten Technical Specification
www.jameshardie.co.nzThis specification covers the use of Titan Façade Panel on buildings, where the maximum wind pressure exerted on the building façade is up to 2.5kPa (ULS). This specification is intended for use by architects or designers/ specifier and installers who …
Design Manual - James Hardie
www.jameshardie.co.nzThe specifier or other party responsible for the project must run through a risk matrix analysis as per E2/AS1 to determine which construction method is applicable to install the external cladding on the project. The designer must also ensure that the bracing capacities published in this specification are appropriate for the intended application.
jameshardie.co.nz CLD Structural Cavity Batten
www.jameshardie.co.nzPortland cement, ground sand, cellulose fibre and water. The product is easily identified by the name 'Stria Cladding' printed on the back of the panels. CLD Structural Cavity Batten is manufactured using a low density fibre cement formulation. The basic composition is Portland cement, ground sand, cellulose fibre, water and proprietary additives.
Related documents
Common Steel Erection Problems and Suggested Solutions
abarsaze.ir· Installed to include anycombination of the above. Installation Conditions. The installation of an-chor bolts is not an easy task under the best of conditions. If the foundation contractor has a firm, level, dry, and uncongested job site, then the steel erector will probably find properly installed anchor bolts.
26.01 Grooved Piping System Design Data | Victaulic
static.victaulic.comwhen allowed to float. Ensure resulting movement of randomly installed systems is not harmful to joints at changes in directions or branch con-nections or to parts of structure or other equipment. Note also that thermal expansion of pipes will add to total movement in these cases. 26.01_1. Design Data. GROOVED PIPING SySTEM – DESIGN DATA 26.01
AIR CONDITIONING RESIDENTIAL BEST PRACTICE …
www.airah.org.auResidential Best Practice Guideline (Victoria) Version 3 .2 8 The following checklist should be adhered to by the Supplier. BEST PRACTICE CHECKLIST Phase Arrive at the agreed time. If an appointment cannot be kept, advise the Customer in advance and agree an alternative time. Inspect the site and discuss the Customer's requirements to
CONCRETE PIPE JOINTS, YOUR BEST CHOICE
www.concretepipe.orgdesign, for vacuum, air or water. ASTM C 924 Standard Practice for Testing Concrete Pipe Sewer Lines by Low-Pressure Air Test Method covers testing of 4 to 24-inch concrete pipe sewer lines using the low-pressure air test method to demonstrate the integrity of the joint. ASTM C 1103 Standard Practice for Joint Acceptance Testing of Installed ...
Best Practice Guide External Wall Insulation
www.inca-ltd.org.ukof technical, installation and component information to promote industry best practice and raise quality standards. This document aims to outline best practice for clients, installers, main contractors, designers and architects so that EWI systems are fit for purpose and installed to a high quality standard to reduce the risk of failure.
BEST PRACTICE GUIDE INSTALLATION OF DRYLINING
www.librasystemsuk.comThis best practice guide provides guidance for the design, selection and installation of non-loadbearing systems only, which comprise a rigid metal frame enclosed by boards that are not subjected to loading from the structure in which it is installed. Drylining systems can be subjected to an imposed load, such as tiling or mounted TVs.
BEST PRACTICE GUIDE INSTALLATION OF SUSPENDED …
www.librasystemsuk.comThis FIS Best Practice Guide for the Installation of Suspended Ceilings is not intended as a definitive technical manual, as the manufacturers’ recommendations must always be followed, but as a guide to the construction team as to best practice. FIS encourages all its members to follow the principles set out in this guide. FOREWORD 1