Vertical Installation Technical Specification - James Hardie
design (SED) project that is outside the scope of this literature, the designer, architect or engineer must ensure that applicable clauses of the NZBC have been considered and a specific design has been undertaken. Linea Oblique Weatherboard is suitable for use in SED project up to a wind pressure of 2.5kPa (ULS). 1 Application 2 Design and scope
Download Vertical Installation Technical Specification - James Hardie
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Specification - jameshardie.co.nz
www.jameshardie.co.nzLinea® Weatherboard Technical Specification April 2016 New Zealand 3 1 Application and scope 1.1 APPLICATION Linea® Weatherboard is …
Design Manual - jameshardie.co.nz
www.jameshardie.co.nzFire and Acoustic Design Manual August 2017 New Zealand 3 1 Introduction readers are familiar with the relevant James Hardie cladding and lining product literature.
Design Manual - James Hardie
www.jameshardie.co.nzFigure 1: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding Figure 2: Vertical junction between Linea™ Weatherboard and James Hardie flat sheet cladding 4 James Hardie Cladding Junction Details Design Manual November 2016 New Zealand Flexible underlay Linea™ Weatherboard Scriber 60 x 3.15mm jolt head
Fire & Acoustic - James Hardie
www.jameshardie.co.nz3.1 External Walls - Timber Frame 8 3.2 External Walls - Steel Frame 10 3.3 Parapet & Wing Walls ... S - StriaTM Cladding ... Refer to recommended safe working practices in each specific product technical specification or installation manual
CLD Structural Cavity Batten Technical Specification
www.jameshardie.co.nzThis specification covers the use of Titan Façade Panel on buildings, where the maximum wind pressure exerted on the building façade is up to 2.5kPa (ULS). This specification is intended for use by architects or designers/ specifier and installers who …
Design Manual - James Hardie
www.jameshardie.co.nzThe specifier or other party responsible for the project must run through a risk matrix analysis as per E2/AS1 to determine which construction method is applicable to install the external cladding on the project. The designer must also ensure that the bracing capacities published in this specification are appropriate for the intended application.
jameshardie.co.nz CLD Structural Cavity Batten
www.jameshardie.co.nzPortland cement, ground sand, cellulose fibre and water. The product is easily identified by the name 'Stria Cladding' printed on the back of the panels. CLD Structural Cavity Batten is manufactured using a low density fibre cement formulation. The basic composition is Portland cement, ground sand, cellulose fibre, water and proprietary additives.
Related documents
User Manual Single Phase Energy Meter - INOGATE
www.inogate.orgsed on ST d the only LMS/COSE osed type d uman mach charge info ilt-in conta uggable PL me basic q ch event re pport logo 12-KP se two wire ude energy nd inquiry, ode solves S (Standard internationa MCommu esign avoid ine interfac rmation is ctor, and v C/GPRS m ueries and cords. ff of meter, 5 / 3 prepaid k measureme anti-tampe the proble ...
Design Manual - James Hardie
www.jameshardie.co.nzYou can also use manual bracing calculation sheets provided in section 21 of this manual. 3 Timber Framing 3.1 General James Hardie’s bracing systems are suitable for timber framed buildings. The framing must comply with the minimum requirements of NZS 3604 ‘Timber Framed Buildings’ or in accordance with the specific engineering design (SED).