DEALER/INSTALLER: GIVE TO HOMEOWNER ... - …

1 SAVE THESE INSTRUCTIONS DEALER/ installer : give TO HOMEOWNERThe Anti-Entrapment Barrier is included in this ladder for the and Canada only, as required by Anti-Entrapment Barrier is NOT intended as a substitute for competent adult you would like to purchase the barrier, please visit our website at: #6100 XINPOOL LADDER 42" TO 54"ASSEMBLY AND INSTRUCTION MANUALMADE IN THE 6100X-wBarrierR12:Confer 6100_12-05_R1 9/14/12 10:01 AM Page 3 Hardware Pack14- #10 x 1-1/4" screws2 - Plugs (wg)2 - 1/4 - 20 x 2" Bolts2 - 1/4 - 20 Acorn Nuts2 - Adjustable Tubes2 - Mounting Blocks2 - Handrail Connectors4 - 1/4 - 20 x 1" Bolts4 - 1/4 - 20 Hex NutsTools Needed for Assembly* - Rubber mallet* - Phillips screwdriver* - Adjustable wrench* - Liquid soap or lubricant* - Cordless Drill* - Drill BitsBarrier Parts List ( and Canada only)(Included in Hardware Pack)

2 4 - #10 x 1-1/4 screws1 - Strip of Foam Pads1 - Large Barrier Section1 - Small Barrier Section1 - Upper Brace1 - Lower BaseModel #6100 XInpool LadderASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLYP arts List2 - Ladder Legs2 - Extension Boots2 - Handrails (to Ladder Legs)2 - Adjustable Tube Handrail(to Adjustable Tube)5 - TreadsIf missing parts call - Toll free - 800-635-3213 or ladder legs on flat a Phillips screwdriver tap outthe plastic film from the three holeson the bottom of leg and the twoholes on the top of leg. Repeat forthe second ladder the end of one of the treads intoone of the keyhole slots of the ladderleg. (The warning on the tread shouldbe facing the front of ladder).

3 It maybe necessary to tap the tread into the slot using a mallet or the tread downward so that it seatsfully into the bottom of the keyhole above procedures using threemore treads making sure all of thewarning labels on treads are facing thefront of ladder. Do not attach the bottom tread at this both handrails on a flat surface. Using a Phillips screwdrivertap out the plastic film from the twoholes located on the flat side of each handrail over the flat arealocated on top of ladder leg. Insertone of the 1/4 - 20 x 1" bolts throughthe ladder leg into the handrail. Placeone 1/4 - 20 hex nut into therecessed area on the handrail andtighten using a Phillips the second bolt and to assemble the second lad-der leg/handrail : This ladder fits deck heights of 42" to 54".

4 2 TREADHANDRAILEXTENSION 6100X-wBarrierR12:Confer 6100_12-05_R1 9/14/12 10:01 AM Page the remaining tread tothe bottom of ladder as two (2) 1/4-20 x2" bolts andtwo (2) acornnuts fastenthe extension boots to the ladder the ladder section down as shownand tap the two handrail connectorsinto the slots with the warning labelsfacing the two adjustable tubehandrails to the handrail the handrails at the top andfasten with a #10 x 1-1/4" for the other the adjustable tubes with a smallamount of liquid soap or lubricant andslide the tube up through the mounting block as boots are not required fora 48" pool. If you have a 48" pool goto step # 12 to continue you have a 52" or tallerpool extension boots will be a Phillips screwdriver tap out theplastic film from the top hole on eachside of the extension a 52 pool slide the extension bootall the way on until the top holes onthe ladder legs and extension bootsare aligned.

5 If you have a 54 pool,back the extension boot off to thenext lower the remaining ladder leg assembly to the opposite ends of the four treads making sure that the curved upper ends areboth facing in the same direction. Tap the treads into place making sure that they are fully seated into the keyhole 6100X-wBarrierR12:Confer 6100_12-05_R1 9/14/12 10:01 AM Page the assembled tube/blockassembly up into the open endof the adjustable tube handrailas Ladder did not include Barrier, skip steps 19 through 21. Continue to step Small and Large BarrierSections into slots on LowerBase as Barrier sections at the topslightly and position Upper Brace overSmall Barrier Section.

6 Next, spread the fingers on the Upper Brace and slideinto position on the Large Barrier the Base and Brace into position, centered, onthe bottom and fourth treads of the ladder. Install thefour (4) #10 x 1-1/4" screws (included in hardwarepack) on a slight angle, first in the Upper brace, then inthe Lower Base. Install the self-adhering foam strips tothe Large Barrier Section as shown in the ladder legs with water through the top fill holes andcover the holes with the plastic plugs. Place the ladder intothe pool, submerge the treads, and tip it sideways so thatthe treads fill a with water. Position the ladder at thedesired location on the deck, making sure that the bottomtread is resting on the floor of the pool and the barrier is asclose to pool wall as possible.

7 Slide the adjustable tubes inor out as required so that they are resting on the deck surface, and the handrail connectors are level. Fasten themounting blocks to the deck surface with eight (8) #10 x 1-1/4" screws. Secure the adjustable tubes to the AdjustableTube Handrail, at the pre-marked locations using two (2)#10 x 1-1/4" screws in each : Ladder MUST be filled with water to prevent : To winterize your ladder unfasten the ladder from the deck and pull the ladder from the the two plugs and lay the ladder on its side to allow the majority of the water to drain out of it. A smallamount of water left in the ladder will notcause any damage.

8 Replace the plugs into the fill holes so that they do not get lost. The ladder may be left 6100X-wBarrierR12:Confer 6100_12-05_R1 9/14/12 10:01 AM Page 6 IMPORTANTFOR YOUR SAFETY* Check the contents of the carton with the Parts listfor this ladder.*If any parts are missing call Toll Free - 800-635-3213 or visit our web site *DO NOTattempt to assemble or install the ladder if there are ANYshortages of parts or hardware.*For proper assembly and installation follow allinstructions in the sequence shown.*Before using the product, after assembly and installation, go over the instructions and proceduresagain to make sure nothing has been overlooked.

9 *Be sure and safe. The manufacturer IS NOTresponsible for improper assembly, installation and RULES* One person on the ladder at a time* Ladder MUSTbe installed per manufacturer s instructions* DANGER:No Jumping or Diving from ladder* Face ladder when entering and leaving pool* To prevent entrapment or drowning DO NOTswim through, behind or around ladder* Ladder to be used as a swimming pool ladder only.* Weight limit - 300 lbs maximum*Warning:Exceeding the maximum weight restriction may cause the ladder to fail.* Consult your local Building Department beforeinstallation of your pool and equipment.*DANGER:Use a cordless drill for assembly and installation. Never use an electric drill in or around the 6100X-wBarrierR12:Confer 6100_12-05_R1 9/14/12 10:01 AM Page 197 Witmer RoadNorth Tonawanda, New York 14120-2421 Toll Free 800-635-3213 FAX in IN THE by:6CP-6100X 9/12 SKIM-IT (SKIMS OFF DEBRIS) -Cut cleaning time 75% with skimmer extensionthat guides debris directly into your most in-ground and above-ground poolskimmers.

10 Corrosion-resistant plastic Skim-Itinstalls in seconds without tools. # 6100 Extension Kit(Part # 6100-EXT) - Raises ladder to reach deck heights from 55 to approximately66 . Kit includes two extension boots, one additional ladder tread, hardware and ACCESSORIES MAY BE PURCHASEDO rder online at PLASTICS, YEAR WARRANTYC onfer Plastics, their swimming pool ladders and steps to be free fromdefects in workmanship for five years from date of NOT RETURN DEFECTIVE PART TO DEALERE-MAIL CONFER PLASTICS AT: PICTURE [S] OF DEFECTIVE PART, A BRIEF DESCRIPTION OF PROBLEM, PROOF OF PURCHASE AND YOUR CONTACT INFORMATION. INFORMATION MAY ALSO BE FAXED TO CONFER PLASTICS AT:716-694-3102OR MAILED TO THE ADDRESS BELOW.