High Speed Optocoupler, 1 MBd, Photodiode with Transistor ...

1 6N135, Semiconductors Rev. , 02-Nov-151 Document Number: 83604 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Speed optocoupler , 1 MBd, Photodiode with Transistor OutputDESCRIPTIONThe 6N135 and 6N136 are optocouplers with a GaAIAs infrared emitting diode, optically coupled with an integrated photo detector which consists of a photo diode and a high- Speed Transistor in a DIP-8 plastic can be transmitted between two electrically separated circuits up to frequencies of 2 MHz. The potential difference between the circuits to be coupled should not exceed the maximum permissible reference Isolation test voltages: 5300 VRMS TTL compatible High bit rates: 1 Mbit/s High common-mode interference immunity Bandwidth 2 MHz Open-collector output External base wiring possible Material categorization: for definitions of compliance please see APPROVALS UL1577 file no.

2 E52744, double protection DIN EN 60747-5-5 (VDE0884-5) available with option 1 cUL components acceptance service no. 5A CQC GB8898-2011, Note(1)Also available in tubes; do not add T to endNCACNCC (VCC)B (VB)C (VO)E (GND)12348765 ORDERING INFORMATION6N13#-X0##TPART NUMBERPACKAGE OPTIONTAPEANDREELAGENCY CERTIFIED / PACKAGECTR (%)UL, CSA 7 19 DIP-86N1356N136 DIP-8, 400 mil, option 6-6N136-X006 SMD-8, option 76N135-X007T (1)6N136-X007T (1)SMD-8, option 9-6N136-X009T (1)VDE, UL, CSA 7 19 DIP-8-6N136-X001 SMD-8, option 76N135-X017T (1)6N136-X017 TSMD-8, option 9-6N136-X019T> mm> mmDIP-8 Option 7 Option 6 Option 96N135, Semiconductors Rev. , 02-Nov-152 Document Number: 83604 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Stresses in excess of the absolute maximum ratings can cause permanent damage to the device.

3 Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified)PARAMETERCONDITIONSYMBOLVALUEU NITINPUTR everse voltageVR5 VForward currentIF25mAPeak forward currentt = 1 ms, duty cycle 50 %IFSM50mAMaximum surge forward currentt 1 s, 300 pulses/s1 AThermal resistanceRth700K/WPower dissipationTamb = 70 CPdiss45mWOUTPUTS upply to 15 VOutput to 15 VEmitter base voltageVEBO5 VOutput currentIO8mAMaximum output current16mABase currentIB5mAThermal resistance300K/WPower dissipationTamb = 70 CPdiss100mWCOUPLERS torage temperature rangeTstg-55 to +150 CAmbient temperature rangeTamb-55 to +100 CSoldering temperaturemax.

4 10 s, dip soldering mm from case bottomTsld260 CELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST voltageIF = 16 voltageIR = 10 AVBR5- -VReverse currentVR = 5 ACapacitanceVR = 0 V, f = 1 MHzCO-30-pFTemperature coefficient, forward voltageIF = 16 mA VF/ COUTPUTL ogic low supply currentIF = 16 mA, VO = open, VCC = 15 VICCL-150- ALogic high supply currentIF = 0 mA, VO = open, VCC = 15 AOutput voltage, output low IF = 16 mA, IO = mA, VCC = = 16 mA, IO = mA, VCC = current, output highIF = 0 mA, VO = VCC = VIOH-3500nAIF = 0 mA, VO = VCC = 15 ACOUPLERC apacitance (input to output)f = 1 MHzCIO- pF6N135, Semiconductors Rev. , 02-Nov-153 Document Number: 83604 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT As per IEC 60747-5-5, , this optocoupler is suitable for safe electrical insulation only within the safety ratings.

5 Compliance with the safety ratings shall be ensured by means of protective circuits. CURRENT TRANSFER RATIO (Tamb = 25 C, unless otherwise specified)PARAMETERTEST transfer ratioIF = 16 mA, VO = V, VCC = V6N135 CTR716-%6N136 CTR1935-%IF = 16 mA, VO = V, VCC = V6N135 CTR5--%6N136 CTR15--%SWITCHING CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST to lowIF = 16 mA, VCC = 5 V, RL = k sIF = 16 mA, VCC = 5 V, RL = k sLow to highIF = 16 mA, VCC = 5 V, RL = k 6N135tPLH sIF = 16 mA, VCC = 5 V, RL = k 6N136tPLH sCOMMON MODE TRANSIENT IMMUNITY (Tamb = 25 C, unless otherwise specified)PARAMETERTEST = 0 mA, VCM = 10 VP-P, VCC = 5 V, RL = k 6N135|CMH|-1000-V/ sIF = 0 mA, VCM = 10 VP-P, VCC = 5 V, RL = k 6N136|CMH|-1000-V/ sLowIF = 16 mA, VCM = 10 VP-P, VCC = 5 V, RL = k 6N135|CML|-1000-V/ sIF = 16 mA, VCM = 10 VP-P, VCC = 5 V, RL = k 6N136|CML|-1000-V/ sSAFETY AND INSULATION RATINGSPARAMETERTEST CONDITIONSYMBOLVALUEUNITC limatic classificationAccording to IEC 68 part 155 / 100 / 21 Pollution degreeAccording to DIN VDE 01092 Comparative tracking index Insulation group IIIaCTI175 Maximum rated withstanding isolation voltageAccording to UL1577, t = 1 minVISO5300 VRMSM aximum transient isolation voltageAccording to DIN EN 60747-5-5 VIOTM8000 VpeakMaximum repetitive peak isolation voltageAccording to DIN EN 60747-5-5 VIORM890 VpeakIsolation resistanceTamb = 25 C, VIO = 500 VRIO 1012 Tamb = 100 C.

6 VIO = 500 VRIO 1011 Output safety powerPSO500mWInput safety currentISI300mAInput safety temperatureTS175 CCreepage distanceDIP-8 7mmClearance distanceDIP-8 7mmCreepage distanceDIP-8, 400 mil, option 6 8mmClearance distanceDIP-8, 400 mil, option 6 8mmCreepage distanceSMD-8, option 7 8mmClearance distanceSMD-8, option 7 8mmCreepage distanceSMD-8, option 9 8mmClearance distanceSMD-8, option 9 8mmInsulation thicknessDTI , Semiconductors Rev. , 02-Nov-154 Document Number: 83604 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)Fig. 1 - LED Forward Current vs. Forward VoltageFig. 2 - Permissible Forward LED Current vs. TemperatureFig. 3 - Permissible Power Dissipation vs. TemperatureFig. 4 - Output Current vs. Output VoltageFig. 5 - Output Current vs.

7 TemperatureFig. 6 - Propagation Delay vs. Ambient TemperatureTamb = 100 CVF - Forward Voltage (V)IF - Forward Current (mA) = 75 CTamb = 25 CTamb = 0 CTamb = -40 Ci6n135_041008060402003020100 Tamb - Ambient Temperature ( C)IF - LED Current (mA)i6n135_05100806040200020406080100120 Tamb - Ambient Temperature ( C)Total Power (mW)DetectorEmitterVO - Output Voltage (V)IO - Output Current (mA)02505101520252015105IF = 35 mAIF = 30 mAIF = 25 mAIF = 20 mAIF = 15 mAIF = 10 mAIF = 5 mAIF = 1 mAIO - Output Current (mA)012345620987- 60 - 40 - 20 020 40 60 80 100 Tamb - Temperature ( C)120at VO = V, VCC = 5 VIF = 20 mAIF = 16 mAIF = 10 mAIF = 1 mAIF = 2 mAIF = 5 mAi6n135_089008007006005004003002001000- 60 - 40 - 20020406080 100tP - Propagation Delay Time (ns)Tamb - Temperature ( C)tPLH at 3 V6N136 at VCC = 5 VIF = 16 mA, RL = k tPLH at VtPHL at VtPHL at 3 V6N135, Semiconductors Rev. , 02-Nov-155 Document Number: 83604 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

8 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 7 - Propagation Delay vs. Ambient TemperatureFig. 8 - Logic High Output Current vs. TemperatureFig. 9 - Small Signal Current Transfer Ratio Input Current Fig. 10 - Switching Timesi6n135_091400120010008006004002000- 60 - 40 - 20100 Tamb - Temperature ( C)tP - Propagation Delay Time (ns)0204060806N135 at VCC = 5 VIF = 16 mA, RL = k tPLHtPHLi6n135_10 Tamb - Temperature ( C)IOH - Collector, IC (nA) 60- 40 - 20100020406080 VCC = VO = 5 VVCC = VO = 15 IF/ IO - Small Signal Current Transfer RatioIF - Forward Current (mA)50 VCC = 5 V, RL = 100 VVOIFtPLHtPHL12348765 IFVORL5 VPulse generatorZO = 50 tr,tf = 5 nsduty cycle 10 %t 100 sCL15 pFIFmonitor100 6N135, Semiconductors Rev. , 02-Nov-156 Document Number: 83604 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 11 - Common-Mode Interference ImmunityPACKAGE DIMENSIONS (in millimeters)DIP-8, Standardi6n135_02 VCMVOVO10 V5V0 VVOL90 %10 %90 %10 %trtftttA: IF = 0 mAB: IF = 16 mA12348765 BVFFIF+VCMVORL5 VAPulse generatorZO = 50 tr,tf = 8 x = ONE , Semiconductors Rev.

9 , 02-Nov-157 Document Number: 83604 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Option 6 DIP-8, Option 7 PIN ONE x = ONE x = Footprint6N135, Semiconductors Rev. , 02-Nov-158 Document Number: 83604 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Option 9 PACKAGE MARKING Fig. 12 - 6N135 Fig. 13 - 6N136 Notes The VDE logo is only marked on option 1 parts. Tape and reel suffix (T) is not part of the package PROFILESFig. 14 - Wave Soldering Double Wave Profile According to J-STD-020 for DIP-8 DevicesFig. 15 - Lead (Pb)-free Reflow Solder Profile According to J-STD-020 for SMD-8 DevicesPIN ONE x = Footprint6N135V YWW 686N136V YWW 682 K/ssecondwavefirst wavewaveca.

10 5 K/s5 sfull line: typicaldotted line:process limitsTime (s)Temperature ( C)30025020015010050005010015020025094 8626 Lead temperature235 C to 260 C100 C to 130 Cca. 200 K/sforced coolingca. 2 K/s050100150200250300050100150200250300 Time (s)Temperature ( C)240 C245 Cmax. 260 Cmax. 120 smax. 100 s217 Cmax. 30 smax. ramp up 3 C/smax. ramp down 6 C/s19841255 C6N135, Semiconductors Rev. , 02-Nov-159 Document Number: 83604 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT AND STORAGE CONDITIONSESD level: HBM class 2 Floor life: unlimitedConditions: Tamb < 30 C, RH < 85 %Moisture sensitivity level 1, according to J-STD-020 Legal Disclaimer Revision: 01-Jan-20191 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.