Transcription of 3590 - Precision Potentiometer
1 Featuresn Bushing mountn Optional AR pin feature n Plastic or metal shaft and bushingsn Wirewoundn Solder lugs or PC pinsn Sealable (Full body seal)n Designed for use in HMI applicationsn RoHS compliant* 3590 - Precision Potentiometer *RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. Specifications are subject to change without should verify actual device performance in their specific applications. The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at Characteristics1 Standard Resistance to 100 K ohmsTotal Resistance Tolerance.
2 5 %Independent Linearity .. %Effective Electrical Angle ..3600 +10 , -0 Absolute Minimum Resistance ..1 ohm or % maximum (whichever is greater)Noise ..100 ohms ENR maximumDielectric Withstanding Voltage (MIL-STD-202, Method 301) Sea Level ..1,500 VAC minimumPower Rating (Voltage Limited By Power Dissipation or 450 VAC, Whichever is Less) +40 C ..2 watts +125 C ..0 wattInsulation Resistance (500 VDC) ..1,000 megohms recommended part numbersEnvironmental Characteristics1 Operating Temperature Range.
3 -40 C to +125 CStorage Temperature Range ..-55 C to +125 CTemperature Coefficient Over Storage Temperature Range 2 .. 50 ppm/ C maximum/unitVibration ..15 G Wiper Bounce .. millisecond G Wiper Bounce .. millisecond maximumLoad Life ..1,000 hours, 2 watts Total Resistance Shift .. 2 % maximumRotational Life (No Load)..1,000,000 shaft revolutions Total Resistance Shift .. 5 % maximumMoisture Resistance (MIL-STD-202, Method 103, Condition B) Total Resistance Shift .. 2 % maximumIP Rating Sealed Versions (-3, -4, -7, and -8).
4 IP 65 Unsealed Versions (-1 -2, -5, and -6) ..IP 40 Moisture Sensitivity Level ..1 ESD Classification (HBM)..N/AMechanical Characteristics1 Stop N-cm (64 ) minimumMechanical Angle ..3600 +10 , -0 Torque Starting & Running .. N-cm ( ) maximum (unsealed) N-cm ( ) maximum (sealed) Mounting ..55-80 N-cm (5-7 ) (plastic) 90-113 N-cm (8-10 ) (metal)Shaft mm ( in.) Runout .. mm ( in.) End Play .. mm ( in.) Radial Play .. mm ( in.) Diameter Runout .. mm ( in.) .. maximumWeight.
5 Approximately 19 GTerminals ..Solder lugs or PC pinsSoldering Condition Manual solid wire or no-clean rosin cored wire; 370 C (700 F) max. for 3 seconds Wave Soldering .. solder with no-clean flux; 260 C (500 F) max. for 5 seconds Wash processes ..Not recommendedMarking ..Manufacturer s name and part number, resistance value and tolerance, linearity tolerance, wiring diagram, and date (Multiple Section Potentiometers) ..1 cup maximumHardware ..One lockwasher and one mounting nut is shipped with each : For Anti-rotation pin add 91 after configuration dash number.
6 Example: -2 becomes -291 to add AR At room ambient: +25 C nominal and 50 % relative humidity nominal, except as noted. 2 Consult manufacturer for complete specification details for resistances below 1k ohms.*RoHS COMPLIANTLEAD FREE*RoHS COMPLIANTVERSIONS AVAILABLELEAD FREE VERSIONS ARE RoHS COMPLIANT* (.480 .020)SOLDER LUGTERMINALPC PIN (.064 .015).305 .003(.012 .0001) (.034)3 (.130 .015) (.100)3 (.480 .020) 3590 - Precision PotentiometerProduct DimensionsSpecifications are subject to change without should verify actual device performance in their specific applications.
7 The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at DIAMETER(SEE PART NUMBERS)SHAFT DIAMETER(SEE PART NUMBERS)13 CCWCWCW2 (.500) MOUNTING SURFACE (.612) RECOMMENDED PC BOARD MOUNTING HOLE .38(.200 .015) .38(.275 .015) .38(.200 .015) + .00/- .13(.406+.000 ).25(.010) (.047) (.312).81(.032) .81(.812 .032) .4(.732 .015) (.48) (.465) .38(.875 .015) (.082) (.200) (.200) (.275)TOLERANCES: EXCEPT WHERE NOTED.
8 508 .127 DECIMALS: .XX (.02), .XXX (.005)FRACTIONS: 1/64 MMDIMENSIONS: (IN.)R MAX.*SEENOTE (.500 .010) MOUNTING SURFACE (.612) (.480) (.465) .38(.875 .015) DIA. (SEEPART NUMBERS)* ..010 SHAFT DIA. (SEEPART NUMBERS)*BUSHING THREAD SPECIFICATIONS: -1, -2, -3, UNF -5, -6, -7, x .38(.200 .015) .38(.275 .015) +.00 (.406 +.000 ) .38(.200 .015).25(.010) (.312).81(.032) .81(.812 .032).81 .25(.032 .010) .38(.732 .015)-2, -4, -6, -8 Configurations-1, -3, -5, -7 ConfigurationsRecommended PCB Layout213 BUSHING DIAMETER(SEE PART NUMBERS)SHAFT DIAMETER(SEE PART NUMBERS)13 CCWCWCW2 (.)
9 500) MOUNTING SURFACE (.612) RECOMMENDED PC BOARD MOUNTING HOLE .38(.200 .015) .38(.275 .015) .38(.200 .015) + .00/- .13(.406+.000 ).25(.010) (.047) (.312).81(.032) .81(.812 .032) .4(.732 .015) (.48) (.465) .38(.875 .015) (.082) (.200) (.200) (.275)TOLERANCES: EXCEPT WHERE NOTED .508 .127 DECIMALS: .XX (.02), .XXX (.005)FRACTIONS: 1/64 MMDIMENSIONS: (IN.)R DIAMETER(SEE PART NUMBERS)SHAFT DIAMETER(SEE PART NUMBERS)13 CCWCWCW2 (.
10 500) MOUNTING SURFACE (.612) RECOMMENDED PC BOARD MOUNTING HOLE .38(.200 .015) .38(.275 .015) .38(.200 .015) + .00/- .13(.406+.000 ).25(.010) (.047) (.312).81(.032) .81(.812 .032) .4(.732 .015) (.48) (.465) .38(.875 .015) (.082) (.200) (.200) (.275)TOLERANCES: EXCEPT WHERE NOTED .508 .127 DECIMALS: .XX (.02), .XXX (.005)FRACTIONS: 1/64 MMDIMENSIONS: (IN.)R DIAMETER(SEE PART NUMBERS)SHAFT DIAMETER(SEE PART NUMBERS)13 CCWCWCW2 (.
