820/860 - FAAC

1 Leading the way ..Installation Manual820/860 Leading the way ..Sliding Gate SystemLeading the way ..1EC MACHINE DIRECTIVE COMPLIANCE DECLARATION(DIRECTIVE 89/392 EEC, APPENDIX II, PART B)Manufacturer:FAAC :Via Benini, 140069 - Zola PredosaBOLOGNA - ITALYH ereby declares that: the 820-860 automation system is intended to be incorporated into machinery, or to be assembled withother machinery to constitute machinery in compliance with the requirementsof Directive 89/392 EEC, and subsequent amendments 91/368 EEC, 93/44 EEC and 93/68 EEC.

2 Complies with the essential safety requirements in the following EEC Directives:73/23 EEC and subsequent amendment 93/68 EEC and subsequent amendments 92/31 EEC and 93/68 furthermore declares that unit must not be put into service until themachinery into which it is incorporated or of which it is a component hasbeen identified and declared to be in conformity with the provisions ofDirective 89/392 EEC and subsequent amendments enacted by the nationalimplementing , 1 January 1997 ManagingDirectorA. Bassi2 IMPORTANT NOTICE FOR THE INSTALLERGENERAL SAFETY REGULATIONS1) WARNING!

3 FAAC strongly recommends to follow these instructions literally for the safety of persons. Improperinstallation or misuse of the product will cause very serious damages to ) Packaging material (plastic, polystyrene etc.) is a potential hazard and must be kept out of reach of )Read the instructions carefully before installing the ) Keep these instructions for future ) This product has been designed and manufactured only for the use stated in this manual. Any other use not expresslyset forth will affect the reliability of the product and/or could be source of ) FAAC cannot be held responsible for any damage caused by improper use or different from the use for whichthe automation system is destined ) Do not use this device in areas subject to explosion.

4 The presence of flammable gas or fumes is a serious ) Mechanical constructive elements must comply with UNI8612, CEN pr EN 12604 and CEN pr EN 12605 outside the EC shall follow the regulations above besides their national normative references in order tooffer the utmost ) FAAC cannot be held responsible for failure to observe technical standards in the construction of gates and doors,or for any deformation of the gates which may occur during ) Installation must comply with UNI8612, CEN pr EN 12453 and CEN pr EN degree of safety of the automation must be C+ ) Before carrying out any operations, turn off the system s main ) An omnipower switch shall be provided for the installation with an opening distance of the contacts of 3 mm or , use a 6A thermomagnetic breaker with multi-pole ) Ensure that there is a differential switch up-line of the electrical system, with a trip threshold of )

5 Check that the earthing plant is in perfect condition and connect it to the metallic parts. Also earth the yellow/greenwire of the ) The automation is fitted with an anti-crush safety system that is a torque control device. In any case, further safetydevices shall be ) The safety devices ( photocells, safety edges, etc.) protect areas where there is a mechanical movementhazard, crushing, entrapment and ) Each installation must be fitted with at least one flashing light ( FAAC LAMP, MINILAMP etc.) as well as a warningplate suitably fixed to the gate, besides the safety devices as per point 16.

6 FAAC cannot be held responsible regarding safety and correct functioning of the automation in the event that partsother than FAAC original parts are ) Use only FAAC original spare parts for maintenance ) Do not carry out any modifications to automation ) The installer must supply all information regarding manual operation of the system in the event of an emergencyand provide the end-user with the "End-user Guide" attached to the ) Keep out of persons when the product is in ) Keep out of reach of children the remote radio controls and any control devices.

7 The automation could beoperated ) The end-user must avoid any attempt to repair or adjust the automation personally. These operations must becarried out exclusively by qualified ) What is not explicitly stated in these instructions is not instructions apply to the following models:820 EMC Z20 CR - 820 EMC - 820 EMC RF - 860 MC Z16 - 860MC - 860 MC RF - 860 EMC Z16 - 860 EMCThe FAAC model 820 and 860 automations for sliding gatesare electromechanical operators which transmit movementto the leaf by means of a pinion with rack or chain coupledin an appropriate manner to the sliding system is guaranteed to be mechanically lockedwhen the motor is not in operation so a lock does not needto be installed.

8 The gear motors have mechanical/electronic clutches which provide the necessary adjustableanti-crushing safety. A convenient manual release deviceallows the gate to be operated in the event of a powerfailure or malfunction. An electronic device allows theopen/closed limit switches to be programmed by a simpleoperation without the need to weld limit switch plates. Theelectronic control unit is incorporated in the gear automations 820 - 860 & 826 MPS have been designedand built for vehicle access control. Do not use for anyother DESCRIPTION AND TECHNICAL CHARACTERISTICSAUTOMATION 820 - 860 & 826 MPSMODEL820860 Power supply230 V (+6% -10%)Power consumption (W)400600 Reduction ratio1:30No.

9 Of pinion teethZ 16 / Z 20 Rack4 module pitch thrust daN50110 Winding thermal protection135 CDuty rating30% (see graph)Oil quantity (l)0,800 Type of oilFAAC XD 220 Temperature range-20 to +55 cGear motor weight (kg)1415 Housing protectionIP 44 Max. gate weight (kg)6001200 Gate speed12 m/min9,6 m/minMax. gate length13 m10 mPartial opening length1,60 m1,20 mCoolingself-ventilatedClutchsingle disc in oil bathHousing treatmentcataphoresisCasing paintingpolyester RAL 7042 Control unit826 MPS (incorporated)Limit switchesprogrammable memory (ADL)DecelerationelectronicGear motor dimensions LxHxD (mm)see Fig.

10 3 Table 1 Gear motor technical characteristics135897611122104 Fig. 1 Transformer 826 MPS electronic control unit Surge capacitor Breather/clutch adjustment screw Electric motor ADL electronic card Limit switch unit Worm screw Crown wheel Emergency release Pinion Casing102030405060708090100012345678910 10 11 12 Percentualedi lav. %Tiempo(h)% Duty cycle% Fr quenced'utilisation% Benutzungs- frequenz% Frecuencia de utilizaci nZeit(Std.)Temps(h)Time (h)Tempo(h)Electric motor technical specificationsModel820860 Motor speed (rpm)14001400 Power consumption (W)400600 Current draw (A)23 Surge condenser20 F30 FPower supply230 V (+6 -10%) 50 UTILISATION CURVEThe curve allows the maximum working time (T) to beobtained as a function of duty cycle (F).