90° Short Radius Elbow - Best Choice of Pipe Fittings ...
Butt Weld, Stainless Fittings, Steel Fittings, Weld Fittings, Pipe Fittings, Steel Pipe Fittings, Stainless Steel Fittings, Butt Weld Fittings, Carbon Steel Fittings, Stainless Steel Pipe Fittings, Elbow, Tee, Cross, Pipe Reducer, Pipe Cap, Stub End Created Date: 12/14/2011 3:00:35 PM
Tags:
Short, Fitting, Below, Radius, Weld, Weld fittings, Short radius elbows
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Spectifications - Best Pipe Fittings, Steel Fittings ...
www.pipefittingweb.comSpectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME B1.20.1 Pipe Threads, General Purpose (Inch)
American, Engineer, Asme, Spectifications, American society of mechanical engineers, Society, Mechanical
Forged High Pressure Pipe Fittings
www.pipefittingweb.comForged High Pressure Pipe Fittings Tel: 886-4-23112576 Fax: 886-4-23112578 E-mail: [email protected]
High, Pressure, Fitting, Forged, Pipe, Forged high pressure pipe fittings
EN 1092-1 Flanges - pipefittingweb.com
www.pipefittingweb.comFlange type (typ) as in EN 1092-1 01 (Plate [slip-on] flanges for welding) 13 (Hubbed threaded flanges) 02 (Loose plate flanges with weld-on plate collar) 21 (Integral flanges)
Pressure Unit Conversion Table - pipefittingweb.com
www.pipefittingweb.comPressure Unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32℉) mm water (4℃) in (60℉) bar Mpa Kpa PSI ( lb/in) atm 1 1.033 760 29.92 10332.56 406.79 1.013 0.1013 101.32 14.69 ata ( kg/cm2 ) 0.968 1 735.56 28.96 10000.03 393.71 0.981 0.0981 98.07 14.22
Unit, Pressure, Table, Conversion, Pressure unit conversion table
Materials - pipefittingweb.com
www.pipefittingweb.comMaterials Chemical Composition % Mechanical Properties C Mn P S Si Ni Cr Mo N Tensile Strength Yield Strength Elongation HRB Stainless Steel
Concentric and Eccentric Reducers
www.pipefittingweb.comConcentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
Reducer, Eccentric, Concentric, Concentric and eccentric reducers
DIN Flanges - pipefittingweb.com
www.pipefittingweb.comDIN Flanges Summary Chart Rated Pressure (in bar) (1 bar = 14.5 psi = 100 kPa)
90° Long Radius Elbow - pipefittingweb.com
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
Caps - pipefittingweb.com
www.pipefittingweb.comCaps MSS SP-75 ANSI B16.9 (in mm) Nominal Pipe Size (NPS) Outside Diameter at Bevel D Length (2) E Limiting Wall Thickness for Length E Length (3)
Long and Short Radius 45°/ 90° Elbows - …
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
Long, Ansi, Below, Radius, Radius elbows, Long radius elbows, Elbows ansi b16
Related documents
SEAMLESS WELDING FITTINGS - GARTH INDUSTRIAL
www.garthindustrial.comfor fittings made from plate. Refer to CCTF catalogue “Stainless Steel Welding Fittings. SPECIAL METALS High Test Steel.High test pipe line welding fittings, conforming to CSA Standard CAN3-Z245.11 or MSS SP-75, are available with physical properties to match pipe with *42,000, 46,000, 52,000, 60,000, 65,000, and over p.s.i. minimum yield ...
API FLANGES - Keddco
keddco.comMSS-SP-55 Quality Standards for Steel Castings for Valves, Flanges and Fittings and other Piping Components. NACE MR-01-75 Sulphide Stress Cracking Resistant Metallic Materials for Oilfield Equipment. Flanges are available as Weld Neck, Integral, Blinds, Target & Test Blinds for use with the following pressure ratings:-MAX. WORKING PRESSURE ...
37° Flared Tube Fittings (SAE J514)
superlokworld.comThe design of SAE 37° Flared Tube Fittings is very efficient. The fitting incorporates the smallest seal area of all fitting types.This seal area, as seen in Fig. 3, is only slightly larger than the fluid flow area. The small seal area results in a compact design, lowassembly torque, and a relatively high-pressure capability.
Tubes, Fitting, Alfred, J514, Sae j514, Flared tube fittings
Pipe Fitters Handbook
pipe-valve-fitting.comANVIL® PIPE FITTERS HANDBOOK 3 Gruvlok Installation Pipe and Flange Data Weld Fitting and Steel Flange Data Table of Contents Gruvlok Tech. Data
TECHNICAL INFORMATION WEIGHTS & DIMENSIONS
www.spearsmfg.comSolvent Weld Connections — Use quality solvent cements and primers formulated for the intended service application, pipe size and type of joint. While While the pipe and fitting materials may be compatible with the intended medium, the solvent cement may not be.