Example: biology
APPENDIX B: MATERIAL SETTINGS - Epilog Laser
Material DPI/Freq. 30 watt 40 watt 50 watt 60 watt 75 watt Mat Board Engraving 400 DPI 70s 100p 70s 90p 70s 80p 70s 70p 70s 60p Cutting 500 f 20s 50p 20s 45p 20s 40p 20s 35p 20s 30p Bottom-up engraving is suggested for mat board etching. Marble
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Settings for Success: Techniques for most popular ...
www.epiloglaser.comDepending on the wattage of your laser, the best approach is to set the laser power at 100 percent and adjust the speed to obtain the desired depth. Wood is a very easy material to work with and you can produce very nice detail with as little as 300 DPI engraving. 600 DPI engraving into wood produces even better results.
APPENDIX B: MATERIAL SETTINGS - Epilog Laser
www.epiloglaser.comlaser out of focus by +.06” - .09” broadens the beam and produces a very bright mark on anodized coating. Lower frequency and higher power …
MINI 18/24 & HELIX - Epilog Laser
www.epiloglaser.comthat turn the laser off if the door is opened during operation, and no special precautions are necessary to operate the high-power laser safely. However, the visible output beam of the Laser Diode Pointer (Red Dot Pointer) is accessible to the operator.
ZING 16 / 24 - Epilog Laser
www.epiloglaser.comThe laser cabinet has safety interlocks that turn the laser off if any access door is opened during operation, and no special precautions are necessary to operate the high-power laser safely. However, the visible output beam of the Laser Diode Pointer (Red Dot Pointer) is …
Section 5: Connecting the Laser to Your Computer
www.epiloglaser.comSection 5: Connecting the Laser to Your Computer 26 The data port connections are on the back of the machine, towards the bottom right. The drawing below shows the location of the data ports on the laser system. USB Port A USB cable is included in the accessory kit. The USB port is located on the right side of the machine, near the rear.
SECTION 3: DRIVER INSTALLATION - Epilog Laser
www.epiloglaser.comWindows 8 and 10: Ethernet Installation SECTION 3: DRIVER INSTALLATION 4. Select Create a new port, then Standard TCP/IP Port. Click Next. 5. Enter the IP Address to match the IP Address you set at the laser in “Setting the IP Address” on page …
Windows 7: Ethernet Installation - Epilog Laser
www.epiloglaser.comWindows 7: Ethernet Installation SECTION 3: DRIVER INSTALLATION 13. Click Next. 14. Click Replace the current driver if requested, then click Next. 15. You can rename your printer here. We have not changed it for this document, but many users like to associate the driver name with the IP Address they are using, for example Epilog Helix 192.168.3.4.
Related documents
Selection Of Material, Shape, And Manufacturing Process ...
peer.asee.orgThe best material and shape combination (using maximum bending strength as a criterion) is that wit h the greatest value of the new index M 2, where (14) ( ) 2 / 3 2 U Ve f M B) Similarly, the best material and shape combination (using maximum stiffness as a criterion) is that with the greatest value of the new index M 3, where (15) ( ) 1 / 2 3 ...
Angle of Material Recommended Material Density Repose ...
www.prodsel.ptwizard.comMaterial Density Repose Group Max. Inclination . Alfalfa, Meal 17 45° 4 . Alfalfa Pellets 41-43 20-29° 2 . Alfalfa Seed 10-15 29° 2 . Almonds, broken or whole 28-30 30-44° 3 . Alum, Fine 45-50 30-44° 3 . Alum, Lumpy 50-60 30-44° 3 . Alumina 50-65 22° 2 10-12 ...
Material Science Quiz Answers - TeachEngineering
www.teachengineering.orgMaterial Science Quiz Answers Answer the following questions without the assistance of a neighbor, friend or teacher. 1. For each material, indicate its material class. quartz 3 Material Classes: steel 2 1. polymer Teflon® 1 2. metal aluminum 2 3. ceramic plywood 4 4. composite fiber glass 4 diamond 3 Zip Lock® bag material 1 paper clip 2
MATERIAL SCIENCE Module 2 Properties of Metals
sites.ntc.doe.gov1.9 Given the values of the associated material properties, CALCULATE the elongation of a material using Hooke's Law. 1.10 DEFINE the following terms: a. Bulk Modulus b. Fracture point 1.11 Given stress-strain curves for ductile and brittle material, IDENTIFY the following specific points on a stress-strain curve. a. Proportional limit b. Yield ...