Ceiling Mount Motion Sensor - AlarmHow.net

1 - 1 - Ceiling Mount Motion SensorINSTALLATION INSTRUCTIONSM odelDT-6360 STCRECESSBUCKETDT-6360 STCRETAINERRINGIf using the retainer ring, place it through, then directly over, thehole in the Ceiling tile. Make sure to orient the retainer ringand recess bucket as shown in Figure , attach the back housing of the DT-6360 STC to the insideof the recess bucket, using the same screw holes and screwsused for surface mounting [#6 ( ) pan head]. Pull severalinches of wiring from the Ceiling through the center hole in therecess bucket and DT-6360 STC back the recess bucket into the hole in the Ceiling , securing it tothe Ceiling (and retainer bracket) with four mounting DT-6360 STC is shipped with a special kit for flush kit contains a recess "bucket" and retainer ring.

2 The retainerring is only needed when flush mounting the unit in Ceiling the tile from the Ceiling (if possible) will make theinstallation process MountingIMPORTANT: To ensure insects do not get inside the DT-6360 STChousing, make sure to seal all holes. (Recommended sealant:silicone RTV.)Note: If surface wiring, use the knockout hole on the side of mounting the DT-6360 STC directly on a Ceiling , use the backcover as a template to mark holes for the mounting screws andwiring. Drill the holes. Then pull several inches of wiring fromthe Ceiling through the center hole in the back the back housing to the Ceiling with the mounting mounting screws: #6 ( ) pan MountingTo remove the front cover, orient the DT-6360 STC so that one ofthe sides with the small rectangular slot in the center is a small flathead screwdriver, gently push down on the slotwhile separating the housing parts.

3 Set the front cover the printed circuit board (PCB) by depressing one ofthe retaining brackets at its sides. Use the microwave antennato carefully pull the PCB PROCEDURENote: If you plan to use the DT-6360 STC's tamperswitches, read the Tamper Installation section on page 1DT-6360 STCF lush Mounting KitThe DUAL TEC 6360 STC Motion Sensor provides maximumcoverage when mounted on ceilings from 8' ( m) to 16' ( ) high. Refer to the System Set-up section to determine whichpassive infrared (PIR) mirror assembly to use at different a mounting location in the center of the protected protected area should be free of objects that might preventthe PIR Sensor from detecting an intruder: large pieces offurniture, room dividers, , infrared energy cannot penetrate solid objects.

4 If thePIR detector is blocked, the DT-6360 STC will not trigger an LOCATIONTo flush Mount the unit, cut a " x " (14 cm x 14 cm) hole inthe Ceiling . Insert the recess bucket into the hole, using it as atemplate to mark drill holes for the four mounting the bucket and drill the screw DT-6360 STC is equipped with two tamper switches: a covertamper and Ceiling tamper. When the tamper switches are used,removing the cover from the Sensor will activate the cover tamper;removing the Sensor from the Ceiling will activate the ceilingtamper. Both tamper switches are normally closed (NC) andinternally wired in cover tamper switch can be used without the Ceiling tamperand requires no modifications to the DT-6360 STC use the Ceiling tamper, remove the square knockout in the rearhousing (directly behind the Ceiling tamper switch), then install ascrew* in the Ceiling .

5 Leave enough of the screw protruding todepress the tamper switch. Refer to Figure the installation is recessed, remove the knockout from the rearhousing, drill a screw hole (behind the knockout) in the recessbucket, then install the screw* in the recess bucket. Leaveenough of the screw protruding to depress the tamper to Figure MOUNTFLUSH MOUNTCEILINGDT-6360 STCS crewto depresstamperScrewto depresstamperDT-6360 STC insiderecess bucketCEILINGPIN FOR PCBKEYHOLEREAR HOUSINGKNOCKOUTLATCHF igure 2 Cover and CeilingTamper Switches*Note: #6 ( )pan head Installation- 2 -SYSTEM SET-UPThe DT-6360 STC package contains two PIR mirror assemblies:one for ceilings from 8' ( ) to 11' ( ) high, another for ceilingsfrom 12' ( ) to 16' ( ) high.

6 The unit is shipped with the8'-11' ( ) mirror change the mirror assembly, remove the front cover and turn itover. Next, remove the protective cap and existing mirror assemblyby depressing the four retaining latches at their sides. Store (ordiscard) the existing mirror and install the new one. Snap theprotective cap back into place, then replace the front the PIR Mirror AssemblyPIR MaskingTo eliminate specific PIR zones from the pattern, mask corre-sponding segments on the PIR mirror with the adhesive-backedmasking tape provided. Remember, segments to be maskedwill be on the side of the mirror OPPOSITE the unwanted Figure the tape has been applied, walk-test the Sensor to ensurethat the correct mirror segments have been MASKINGMATERIALPLACED HEREWILL BLOCK ZONESHITTING HEREF igure 4 Masking the PIR Mirrors1 SYSTEM TESTINGDT-6360 STC sensors are equipped with two diagnostic LEDs:green for PIR and yellow for microwave.

7 The red LED is used toindicate an alarm power to the Sensor and wait until self-test is completed (90seconds). Begin walk-testing after all three LEDs have gone 5DT-6360 STC PCB2 EOL = End-of-Line (spare) terminal. The Trouble Output is activated when a self-test failure or an INFORMER condition occurs. Refer to THE INFORMER CIRCUIT and the TROUBLESHOOTING the proper polarity, wire the Sensor as shown below(use 22 to 14 AWG). Note: Reverse polarity will not damage the COMNOV-TAMPER SWITCHN ormally Closed(NC) with cover on25 mA, 30 LED ENABLE orCOMMAND INPUT(Self-Test Initiate) ActiveLow 0 to V InactiveHigh 6 to V+ InputImpedance 110 Kohms(minimum).

8 OPEN COLLECTORTROUBLE OUTPUTVce .3V max @ 50mA. 1K seriesprotection 3 WiringDiagramALARM RELAY125 mA, 25 VDC. 22 ohmseries protection 12 VDC,typically40 mA;maximum50 mANote: Do not leave excess wire inside the unit. Push as much wire aspossible into the Ceiling when returning the PCB to its : For proper wiring methods, refer to National Electrical Code NFPA Front Cover After Installation (flush Mount )After installing and walk-testing the DT-6360 STC flush Mount , youmay need to make adjustments. Use a screwdriver to reopen thefront the screwdriver as far as it will go in the grooves inside therecess bucket. Gently press outward to release the latches holdingthe front cover in sensors are equipped with a microwave rangethumbwheel (R32) for range adjustment.

9 (Refer to Figure 5.)Set the range at MINIMUM by turning the thumbwheel all theway to the you perform the walk-test, gradually turn the thumbwheel tothe right to increase the microwave sensitivity until the desiredranged is Range AdjustmentWalk-testWalk across the protected area at the ranges to be to four normal steps make the diagnostic LEDs light, andthe red LED should indicate an alarm condition. When there isno Motion in the protected area, all three LEDs should be INPUT / REMOTE LED ENABLEP osition W4 determines what function the Command Input(CMD) terminal will a jumper at position W4 makes the CMD terminalfunction as a Remote LED Enable terminal.

10 If the signal to theRemote LED Enable terminal is low, the LEDs are enabled. Ifthe signal to the terminal is high, the LEDs are disabled. How-ever, if a self-test error occurs, the LEDs will light regardless ofthe state of the CMD terminal functions as a Command Input terminal whenthe jumper is removed from position W4. A momentary lowsignal to the terminal (at least .5 seconds) will initiate the DISABLE (Local)To disable the diagnostic LEDs and alarm LED, remove thejumper from position W2 on the PCB. (See Figure 5.)* If Self-Test fails or an INFORMER condition occurs, LEDs indicates nature of problem (see Tables 1,2 & 3)ALARM & DIAGNOSTIC LEDs:Yellow - During normal operation LED flashes ON when a MICROWAVE event is detected.