D C a n d A C S w i t c h i n g C h a r a c t e r i s t i ...

1 Zynq UltraScale+ MPSoC Data Sheet: DC and AC Switching Characteristics DS925 ( ) June 23, 2021 Product Specification Summary The xilinx Zynq UltraScale+ MPSoCs are available in -3, -2, -1 speed grades, with -3E devices having the highest performance. The -2LE and -1LI devices can operate at a VCCINT voltage at or and are screened for lower maximum static power. When operated at VCCINT = , using -2LE and -1LI devices, the speed specification for the L devices is the same as the -2I or -1I speed grades. When operated at VCCINT = , the -2LE and -1LI performance and static and dynamic power is reduced. DC and AC characteristics are specified in extended (E), industrial (I), automotive (Q), and military (M). temperature ranges. Except the operating temperature range or unless otherwise noted, all the DC and AC. electrical parameters are the same for a particular speed grade (that is, the timing characteristics of a -1 speed grade extended device are the same as for a -1 speed grade industrial device).

2 However, only selected speed grades and/or devices are available in each temperature range. The XQ references in this data sheet are specific to the devices available in XQ Ruggedized packages. See the Defense-Grade UltraScale Architecture Data Sheet: Overview (DS895) for further information on XQ Defense- grade part numbers, packages, and ordering information. All supply voltage and junction temperature specifications are representative of worst-case conditions. The parameters included are common to popular designs and typical applications. This data sheet, part of an overall set of documentation on the Zynq UltraScale+ MPSoCs, is available on the xilinx website at DC Characteristics Absolute Maximum Ratings Table 1: Absolute Maximum Ratings Symbol Description1 Min Max Units Processor System (PS). VCC_PSINTFP PS primary logic full-power domain supply voltage V.

3 VCC_PSINTLP PS primary logic low-power domain supply voltage V. VCC_PSAUX PS auxiliary supply voltage V. Copyright 2015-2021 xilinx , Inc. xilinx , the xilinx logo, Alveo, Artix, Kintex, Spartan, Versal, Virtex, Vitis, Vivado, Zynq, and other designated brands included herein are trademarks of xilinx in the United States and other countries. AMBA, AMBA Designer, Arm, ARM1176JZ-S, CoreSight, Cortex, PrimeCell, Mali, and MPCore are trademarks of Arm Limited in the EU and other countries. PCI, PCIe, and PCI Express are trademarks of PCI-SIG and used under license. The DisplayPort Icon is a trademark of the Video Electronics Standards Association, registered in the and other countries. All other trademarks are the property of their respective owners. DS925 ( ) June 23, 2021 Send Feedback Product Specification 1. Zynq UltraScale+ MPSoC Data Sheet: DC and AC Switching Characteristics Table 1: Absolute Maximum Ratings (cont'd).

4 Symbol Description1 Min Max Units VCC_PSINTFP_DDR PS DDR controller and PHY supply voltage V. VCC_PSADC PS SYSMON ADC supply voltage relative to GND_PSADC V. VCC_PSPLL PS PLL supply voltage V. VPS_MGTRAVCC PS-GTR supply voltage V. VPS_MGTRAVTT PS-GTR termination voltage V. VPS_MGTREFCLK PS-GTR reference clock input voltage V. VPS_MGTRIN PS-GTR receiver input voltage V. VCCO_PSDDR PS DDR I/O supply voltage V. VCC_PSDDR_PLL PS DDR PLL supply voltage V. VCCO_PSIO PS I/O supply V. VPSIN2 PS I/O input voltage VCCO_PSIO + V. PS DDR I/O input voltage VCCO_PSDDR + V. VCC_PSBATT PS battery-backed RAM and battery-backed real-time clock (RTC) V. supply voltage Programmable Logic (PL). VCCINT Internal supply voltage V. VCCINT_IO 3 Internal supply voltage for the I/O banks V. VCCAUX Auxiliary supply voltage V. VCCBRAM Supply voltage for the block RAM memories V. VCCO Output drivers supply voltage for HD I/O banks V.

5 Output drivers supply voltage for HP I/O banks V. VCCAUX_IO4 Auxiliary supply voltage for the I/O banks V. VREF Input reference voltage V. VIN2, 5, 6 I/O input voltage for HD I/O banks VCCO + V. I/O input voltage for HP I/O banks VCCO + V. IDC Available output current at the pad 20 20 mA. IRMS Available RMS output current at the pad 20 20 mA. GTH or GTY Transceiver7. VMGTAVCC Analog supply voltage for transceiver circuits V. VMGTAVTT Analog supply voltage for transceiver termination circuits V. VMGTVCCAUX Auxiliary analog Quad PLL (QPLL) voltage supply for transceivers V. VMGTREFCLK Transceiver reference clock absolute input voltage V. VMGTAVTTRCAL Analog supply voltage for the resistor calibration circuit of the V. transceiver column VIN Receiver (RXP/RXN) and transmitter (TXP/TXN) absolute input V. voltage IDCIN-FLOAT DC input current for receiver input pins DC coupled RX 10 mA.

6 Termination = floating8. IDCIN-MGTAVTT DC input current for receiver input pins DC coupled RX 10 mA. termination = VMGTAVTT. IDCIN-GND DC input current for receiver input pins DC coupled RX 0 mA. termination = GND9. IDCIN-PROG DC input current for receiver input pins DC coupled RX 0 mA. termination = programmable10. DS925 ( ) June 23, 2021 Send Feedback Product Specification 2. Zynq UltraScale+ MPSoC Data Sheet: DC and AC Switching Characteristics Table 1: Absolute Maximum Ratings (cont'd). Symbol Description1 Min Max Units IDCOUT-FLOAT DC output current for transmitter pins DC coupled RX 6 mA. termination = floating IDCOUT-MGTAVTT DC output current for transmitter pins DC coupled RX 6 mA. termination = VMGTAVTT. Video Codec Unit VCCINT_VCU Internal supply voltage for the video codec unit V. PL System Monitor VCCADC PL System Monitor supply relative to GNDADC V.

7 VREFP PL System Monitor reference input relative to GNDADC V. Temperature11. TSTG Storage temperature (ambient) 65 150 C. TSOL Maximum dry rework soldering temperature 260 C. Maximum reflow soldering temperature for SBVA484, SFVA625, 250 C. and SFVC784 packages Maximum reflow soldering temperature for UBVA494, UBVA530, 245 C. FBVB900, FFVC900, FFVB1156, FFVC1156, FFVB1517, FFVF1517, FFVC1760, FFVD1760, and FFVE1924 packages Maximum reflow soldering temperature for SFRA484, SFRC784, 225 C. FFRB900, FFRC900, FFRB1156, FFRC1156, FFRB1517, and FFRC1760. packages Tj Maximum junction temperature 125 C. Notes: 1. Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied.

8 Exposure to Absolute Maximum Ratings conditions for extended periods of time might affect device reliability. 2. When operating outside of the recommended operating conditions, refer to Table 6, Table 7, and Table 8 for maximum overshoot and undershoot specifications. 3. VCCINT_IO must be connected to VCCBRAM. 4. VCCAUX_IO must be connected to VCCAUX. 5. The lower absolute voltage specification always applies. 6. For I/O operation, see the UltraScale Architecture SelectIO Resources User Guide (UG571). 7. For more information on supported GTH or GTY transceiver terminations see the UltraScale Architecture GTH Transceivers User Guide (UG576) or UltraScale Architecture GTY Transceivers User Guide (UG578). 8. AC coupled operation is not supported for RX termination = floating. 9. For GTY transceivers, DC coupled operation is not supported for RX termination = GND.

9 10. DC coupled operation is not supported for RX termination = programmable. 11. For soldering guidelines and thermal considerations, see the Zynq UltraScale+ Device Packaging and Pinouts Product Specification User Guide (UG1075). DS925 ( ) June 23, 2021 Send Feedback Product Specification 3. Zynq UltraScale+ MPSoC Data Sheet: DC and AC Switching Characteristics Recommended Operating Conditions Table 2: Recommended Operating Conditions Symbol Description1, 2 Min Typ Max Units Processor System VCC_PSINTFP3 PS full-power domain supply voltage V. For -1LI and -2LE (VCCINT = ) devices: PS full-power domain V. supply voltage For -3E devices: PS full-power domain supply voltage V. VCC_PSINTLP PS low-power domain supply voltage V. For -1LI and -2LE (VCCINT = ) devices: PS low-power domain V. supply voltage For -3E devices: PS low-power domain supply voltage V. VCC_PSAUX PS auxiliary supply voltage V.

10 VCC_PSINTFP_DDR3 PS DDR controller and PHY supply voltage V. For -1LI and -2LE (VCCINT = ) devices: PS DDR controller and V. PHY supply voltage For -3E devices: PS DDR controller and PHY supply voltage V. VCC_PSADC PS SYSMON ADC supply voltage relative to GND_PSADC V. VCC_PSPLL PS PLL supply voltage V. VPS_MGTRAVCC4 PS-GTR supply voltage V. VPS_MGTRAVTT4 PS-GTR termination voltage V. VCCO_PSDDR5 PS DDR I/O supply voltage V. VCC_PSDDR_PLL PS DDR PLL supply voltage V. VCCO_PSIO6 PS I/O supply V. VPSIN PS I/O input voltage VCCO_PSIO + V. PS DDR I/O input voltage VCCO_PSDDR + V. VCC_PSBATT7 PS battery-backed RAM and battery-backed real-time clock (RTC) V. supply voltage Programmable Logic VCCINT PL internal supply voltage V. For -1LI and -2LE (VCCINT = ) devices: PL internal supply V. voltage For -3E devices: PL internal supply voltage V. VCCINT_IO 8 PL internal supply voltage for the I/O banks V.