1 TECHNICAL DATA SHEET. DUPONT TYVEK COMMERCIALWRAP D. A DURABLE, high PERFORMANCE, MECHANICALLY FASTENED AIR AND WATER BARRIER. ENGINEERED TO IMPROVE DRAINAGE AND TO STAND UP TO THE COMMERCIAL JOB SITE. DESCRIPTION. TYVEK COMMERCIALWRAP D offers superior drainage and durability for commercial buildings. It features a specially engineered surface texture that provides enhanced water drainage under a wide variety of facades in climates that may require additional drainage. As a part of DUPONT TYVEK Commercial Air and Water Barrier Systems, TYVEK . COMMERCIALWRAP D can easily be integrated with other system components to provide superior air and water hold-out with high tear-resistance, high wind-load- resistance and 9-month UV resistance.
2 TYVEK COMMERCIALWRAP D is backed by a 10-year limited warranty and industry-leading technical support. TYPICAL PROPERTIES (JULY, 2016). Please contact your local DUPONT TYVEK Specialist before writing specifications around this product. Product properties are as follows: Test Method Property Unit Value ASTM E2357 Air Penetration Resistance cfm/ft @ psf 2. < PRODUCT INFORMATION FEATURES/BENEFITS Gurley Hill Air Penetration Resistance sec/100cc >750. Air and Water Barrier Performance (TAPPI T-460). Offers the ideal combination of enhanced drainage, air and water holdout plus ASTM E1677 Air Penetration Resistance cfm/ft2 @ psf Type 1.
3 Vapor permeability. ASTM E2178 Air Penetration Resistance cfm/ft @ psf 2..001. Air Barrier Association of America evaluated to exceed ABAA, ASHRAE and IECC air leakage requirements when tested in accordance with ASTM E2357. Wall Assembly Air Penetration ASTM E283 cfm/ft2 @ psf < Resistance Drainage Method B. Offers > 98% drainage efficiency when tested in accordance with ASTM E2273. ASTM E96-05 Water Vapor Transmission 212. g/m2-24 hrs Ease of Installation ASTM E96-05 Water Vapor Transmission Method B (perms) 30. Easily installed, prior to the building's exterior facade, to help protect against air AATCC 127 Water Penetration Resistance cm 235.
4 And water infiltration. Wall Assembly Water No high Performance Durability ASTM E331 Tested to 15 psf Penetration Resistance leakage Offers high tear-resistance and high wind-load-resistance to help stand up to ASTM E2273 Drainage Efficiency % >98. commercial construction site conditions. Withstands up to nine months of UV exposure. TAPPI T-410 Basis Weight oz/yd 2. Sustainable Solutions ASTM D882 Breaking Strength lbs/in 33/41. DUPONT TYVEK COMMERCIALWRAP D may contribute toward LEED points in the ASTM D1117 Tear Resistance lbs 6/9. areas of Energy and Atmosphere (EA): Optimizing the Building Envelope and Indoor Flame Spread 15 Class Environmental Air Quality (EQ): Construction IAQ Management Plan and Low ASTM E84 Surface Burning Characteristics Index Class A.
5 Emitting Materials. In addition, the use of a continuous air barrier is a prerequisite for LEED applications requiring compliance with ASHRAE Smoke Developed 25. ASTM E84 Surface Burning Characteristics Index Class Class A. By helping to effectively seal the building envelope, TYVEK COMMERCIALWRAP D. helps to reduce the amount of energy required for heating and cooling. Flame Propagation/Multiple NFPA 285 Pass Assemblies Complete System Days 270. TYVEK COMMERCIALWRAP D can be integrated with DUPONT self-adhered flashing Ultra Violet Light Exposure (UV). Months 9. products and TYVEK Fluid Applied products to offer seamless protection for wall systems that require mechanically fastened and fluid applied air and water barriers .
6 Test results shown represent roll averages. Individual results may vary either above or below averages due to normal manufacturing variations, while continuing to meet product specifications. TECHNICAL DATA SHEET. DUPONT TYVEK COMMERCIALWRAP D. A DURABLE WEATHER BARRIER ENGINEERED FOR ENHANCED DRAINAGE. PRODUCT DESCRIPTION TESTING/CODE COMPLIANCE Other TYVEK COMMERCIALWRAP D is made from 100% flash Moisture Protection ASTM E 84 Standard Test Method for Surface spunbonded high density polyethylene fibers which have Weather-Resistant barriers Burning Characteristics of Building Materials been bonded together by heat and pressure, without The 2015 International Building Code (IBC, Section NFPA 285 Standard Fire Test Method for Evaluation binders or fillers, into a tough durable sheet structure.)
7 Weather Protection) requires that exterior walls shall of Fire Propagation Characteristics of Exterior Additives have been incorporated into the polyethylene to provide the building with a weather-resistant exterior Non-Load-Bearing Wall Assemblies Containing provide ultraviolet light resistance. wall envelope. This shall include flashing, as described in Combustible Components Section TYVEK COMMERCIALWRAP D and where ASTM E 2273 Standard Test Method for Determining INSTALLATION/USE INSTRUCTIONS applicable, DUPONT self-adhered flashing and accessory the Drainage Efficiency of Exterior Insulation and Please refer to DUPONT Installation Guidelines for products, have been tested and meet weather-resistant Finish Systems (EIFS) Clad Wall Assemblies complete instructions.
8 Barrier codes and standards requirements. The following test methodologies were used: TYVEK COMMERCIALWRAP D, in conjunction with DUPONT Safety Precautions for Use self-adhered flashing and accessory products, have been TYVEK COMMERCIALWRAP D is slippery and should not be ASTM E331 Standard Test Method for Water evaluated according to Air Barrier Association of America used in any application where it will be walked on. In Penetration of Exterior Windows, Skylights, Doors, (ABAA) protocol and are listed at the ABAA website addition, DUPONT recommends using kick jacks, and Curtain Walls by Uniform Static Pressure under ABAA evaluated Air Barrier Assemblies , scaffolding, or lifts for exterior work above the first floor.
9 ASTM E2556 Standard Specification for Vapor If ladders must be used, extra caution must be taken to Permeable Flexible Sheet Water-resistive barriers use them safely by following the requirements set forth intended for mechanical attachment NOTICE. in ANSI Standards , , and for ladders made TYVEK COMMERCIALWRAP D should be covered with the ASTM E96-00 Standard Test Methods for Water Vapor of wood, aluminum, and fiberglass, respectively. facade within nine months to limit UV exposure. Follow Transmission of Materials; Water resistive barriers facade manufacturer's installation and maintenance TYVEK COMMERCIALWRAP D is combustible and should are typically vapor permeable, which is generally requirements in order to maintain water holdout.
10 Be protected from flames and other high heat sources. desirable because it allows for drying of incidental TYVEK COMMERCIALWRAP D will melt at 275 F (135 C) moisture intrusion into the wall assembly MATERIAL STORAGE/DISPOSAL. and if the temperature of the product reaches 750 F AATCC 127 Hydrostatic Head Test for water-resistant TYVEK COMMERCIALWRAP D should be stored in a clean, (400 C), it will burn and the fire may spread and fall away barrier materials, measuring pressure to failure or dry environment. from the point of ignition. For more information, call time of failure at a given pressure 1-800-44- TYVEK .