1 fieldvue DVC2000 Digital ValveControllerThe fieldvue DVC2000 Digital Valve Controller issimple to use, compact, and designed for easymounting. It converts a 4-20 mA input signal into apneumatic output signal, which feeds the control valveactuator. Instrument setup is performed with anenclosed push button and liquid crystal display (LCD)interface. The interface supports multiple languages,available in two language pack DVC2000 uses a two-stage positioner design. Thepre-amplifier stage provides high static gain forresponsiveness to small changes in the input power amplifier stage delivers the right volume ofair to the actuator, combining superior dynamicperformance with minimal steady-state high performance, linkage-less feedback systemeliminates physical contact between the Valve stemand the positioner.
2 There is no wear of parts so cyclelife is maximized. Additionally, the elimination oflevers and linkages reduces the number of mountingparts and the mounting complexity. Positionerreplacement and maintenance is simplified becausethe feedback parts stay connected to the to meet intrinsically safe and non-incendiverequirements, this instrument delivers scalablefunctionality and high performance in a small Digital Valve ControllerD103167X012 Product : DVC2000 August 2017 DVC2000 Digital Valve ControllerD103167X012 Product : DVC2000 August 2017 2 SpecificationsAvailable MountingsJIntegral mounting to Fisher 657/667 or GXactuatorsJSliding-stem applicationsJQuarter-turn rotary applicationsDVC2000 Digital Valve controllers can also bemounted on other actuators that comply with IEC 60534-6-1, IEC 60534-6-2, VDI/VDE 3845 andNAMUR mounting SignalAnalog Input Signal: 4-20 mA DC, nominal.
3 Can beconfigured for split rangeMinimum Voltage: Voltage available at instrumentterminals must be volts for analog control, for HARTr communicationMaximum Voltage: 30 VDCM inimum Control Current: mA (below mAmay cause microprocessor restart)Overcurrent Protection: Input circuitry limits currentto prevent internal damageReverse Polarity Protection: No damage occurs fromreversal of loop currentOutput SignalPneumatic signal as required by the actuator, up tofull supply pressureMinimum Span: bar (7 psig)Maximum Span: 7 bar (101 psig)Action: Single Acting, directSupply Pressure(1)Recommended: bar (7 psig) greater than themaximum actuator requirementsMaximum: 7 bar (101 psig)Supply medium must be clean, dry air ornoncorrosive gas that meets the requirements of ISA Standard or ISO 8573-1 Temperature Limits(1)-40 to 80_C (-40 to 176_F).
4 LCD may not be readablebelow -20_C (-4_F).Air Consumption(2)Supply pressureAt bar (22 psig)(3): normal m3/h ( scfh)At 4 bar (58 psig)(4): normal m3/h ( scfh)Air Capacity(2)Supply pressureAt bar (22 psig)(3): normal m3/h (167 scfh)At 4 bar (58 psig)(4): normal m3/h (338 scfh)Independent Linearity of output spanElectromagnetic CompatibilityMeets EN 61326-1:2013 Immunity Industrial locations per Table 2 of the EN 61326-1 standard. Performance is shown in table 1 below Emissions Class A ISM equipment rating: Group 1, Class ATested to NAMUR NE21 requirementsVibration Testing MethodTested per Section Aresonant frequency search is performed on all threeaxes. The instrument is subjected to the ISA specified1/2 hour endurance test at each major resonance,plus an additional two million ImpedanceThe input impedance of the DVC2000 activeelectronic circuit is not purely resistive.
5 Forcomparison to resistive load specifications, anequivalent impedance of 450 ohms may be used. Thisvalue corresponds to 9 V @ 20 ClassificationHazardous Area:CSA Intrinsically Safe and Non-incendiveFM Intrinsically Safe and Non-incendiveATEX Intrinsically SafeIECEx Intrinsically SafeContact your Emerson sales office or Local BusinessPartner if additional information is requiredElectrical Housing:CSA IP66, Type 4 XFM IP66 ATEX IP66 IECEx IP66-continued- DVC2000 Digital Valve ControllerD103167X012 Product : DVC2000 August 2017 3 Specifications (continued)Other Classifications/CertificationsCUTR Customs Union Technical Regulations (Russia,Kazakhstan, Belarus, and Armenia)INMETRO National Institute of Metrology,Quality and Technology (Brazil)KGS Korea Gas Safety Corporation (South Korea)NEPSI National Supervision and Inspection Centrefor Explosion Protection and Safety ofInstrumentation (China)PESO CCOE Petroleum and Explosives SafetyOrganisation - Chief Controller of Explosives (India)Contact your Emerson sales office or Local BusinessPartner for classification/certification specificinformationConnectionsStandardSu pply and Output Pressure: G1/4 internalElectrical: M20 internalOptionalSupply and Output Pressure: 1/4 NPT internalElectrical.
6 1/2 NPT internalMaterials of ConstructionHousing and Cover: A03600 low copper aluminumalloyElastomers: nitrile, fluorosiliconeStem TravelMinimum: mm ( inch)Maximum: 606 mm (23-7/8 inches)Shaft RotationMinimum: 45_Maximum: 90_MountingDesigned for direct actuator mounting. Forweatherproof housing capability, the vent must bepositioned at the lowest point of the kg ( lbs)DimensionsRefer to figure 3 OptionsJAirset: Fisher 67 CFR with filterLanguage Packs: JStandard: English, German,French, Italian, Spanish, Japanese, Chinese,Portuguese, Russian, Polish, and CzechJOptional: English, German, French, Italian, Spanish,Japanese, Chinese, and ArabicJPipe-away ventJLimit Switches: Two isolated switches, configurablethroughout calibrated travel rangeSupply Voltage: 5-30 VDCOFF State: to mAON State: to mA (above 5 volts)Reference Accuracy: 2% of travel span(5)JTransmitter: 4-20 mA output, isolated Supply Voltage: 8-30 VDC Fault Indication: offrange high or lowReference Accuracy: 1% of travel span(5)1.
7 The pressure/temperature limits in this document and any applicable standard or code limitation should not be exceeded. Note: Temperature limits vary based on hazardous area Normal m3/hour - Normal cubic meters per hour at 0_C and bar, absolute. Scfh - Standard cubic feet per hour at 60_F and Low pressure relay: 0 to bar (0 to 50 psig).4. High pressure relay: to bar (51 to 102 psig).5. Typical values when calibrated at Simplicity The DVC2000 is easy to use. If you aremounting the instrument for the first time, thelinkage-less feedback system is easy to install. Oncea magnet array is assembled to the Valve stem,positioner replacement is simple since there are nophysically connected its very basic functionality, the DVC2000 digitalvalve Controller has a local user interface that willallow you to configure, calibrate, and tune theinstrument.
8 If the I/O Options Package is installed,you can calibrate the 4-20 mA transmitter andconfigure the limit switch action. Running the QuickSetup routine calibrates and tunes the instrumentspecifically for that full text display in the local interface is easy tonavigate, in part due to the selection of unit can be configured to display English,German, French, Italian, Spanish, Japanese orChinese. The standard language pack also includesPortuguese, Russian, Polish, and Czech. An optionallanguage pack replaces these four languages Digital Valve ControllerD103167X012 Product : DVC2000 August 2017 4n Reliability The DVC2000 is based on thefield-proven fieldvue technology. Years of controlexperience has brought this product line to a highlevel of reliability and Performance The two-stage positioner designprovides a mechanical platform that enablesresponsiveness to small input changes and tighterprocess control.
9 The Digital tuning algorithm allowsoptimal response to get the Valve to its desiredposition Diagnostics Local User Interface: DVC2000instruments come standard with a liquid crystaldisplay. Predefined instrument and valvediagnostics are built into the firmware to alert you ifthere are any problems with the mounting,electronics, hardware, or Valve performance. Handheld Field Communicator: DVC2000instruments are packed with user-configurablealerts and alarms. These flags provide notification ofcurrent status and potential Valve and instrumentproblems through alerts such as travel deviation,travel limit, cycle count, and travel software: Tests can be performed toidentify problems with the entire control valveassembly using ValveLink software. Using valvestem travel feedback, actuator pressure sensor, andother sensors on the instrument, the health of thecontrol Valve can be evaluated while the Valve is stillin service and fully operational.
10 This helps topinpoint problems without disrupting the process -before the equipment I/O Options Package The DVC2000 is availablewith an I/O Options Package which includes two (2)integral limit switches and a stem positiontransmitter. The limit switches are configurable foropen and closed Valve indication at any pointthroughout the calibrated travel range. The positiontransmitter provides a 4-20 mA signal for valveposition feedback verification. As an integralcomponent to the instrument, this option moduleavoids the need for difficult-to-mount externalswitches and 4-20 mA SystemsBecause the DVC2000 instrument operates with a4-20 mA control signal, it directly replaces olderanalog instruments. Microprocessor based electronicsprovide improved control performance along withrepeatable and reliable configuration and with ValveLink Softwareand HART MultiplexersHART communication allows you to extract morevalue from the DVC2000 instrument beyond itsinherent improved performance.