EBARA Submersible Stainless Steel Pumps Optima/EPD

1 EBARA Submersible Stainless Steel PumpsOptima/EPDC ontentsProject:Model:Chk d:Date:EBARAF luid (803) 327-5005 (803) 327-5097 (fax)rev. 03/12 Model Selection PerformanceDimensionsSectional ViewChartCurvePumpMotor DataOptima-3AS1 *Note:UL and CSA listed; Model Optima UL certified Submersible Stainless Steel PumpsOptima/EPDM odel DesignationProject:Model:Chk d:Date:EBARAF luid (803) 327-5005 (803) 327-5097 (fax)rev. 09/08 MODEL TYPEEPD EBARA PRO DrainerOptima* EBARA , Plastic impeller, PRO DrainerHP3 = 1/3HP5 = 1/2HP7 = 3/4HP10 = 1 HP15 = 11/2 HPOPERATiOnM = ManualA= AutomaticS= Slimline AutomaticPHASES single phaseT three phaseVOLTAGE1 1152 2304 460*note: Only the 1/3 HPunits offer both a plastic impeller and a Stainless Steel Submersible Stainless Steel PumpsOptima/EPDS pecificationsProject:Model:Chk d:Date:EBARAF luid (803) 327-5005 (803) 327-5097 (fax)rev.

2 05/11 Model Optima-3AS1 EPD-3AS1 Optima-3SS1 EPD-5AS1 and EPD-7AS1 Automatic Operation PumpsPerformance: ISO 2548 StandardOptionalDischarge Size1/3HP 11/4inch1/2HP and 3/4HP 11/2inchRange of HP1/3, 1/2, and 3/4 HPRange of PerformanceCapacity to 72 GPMHead to 57 feetLimitationMaximum Water Temperature122 F/50 C (140 F/60 C intermittent duty)Solids3/8'' Spherical (2% by concentration)Synchronous Speed3600 RPMM aterialsCasing304L Stainless SteelImpeller304L Stainless Steel *Shaft303 Stainless SteelMotor Frame304L Stainless SteelFasteners304L Stainless SteelShaft Seal(Double)**Material UpperNBR Fitted Carbon/Ceramic 1/2, 3/4, 1, and 11/2 HPMaterial LowerFPM Fitted Silicon Carbide/Silicon Carbide 1/2, 3/4, 1, and 11/2 HPImpeller TypeSemi-OpenBearingSealed Ball BearingMotorAir-filled, Insulation Class F, 2 Pole, Rated Continuous Duty Permanent Split CapacitorSingle Phase115 VoltMotor ProtectionBuilt-in Motor Protection w/Auto ResetPower CordUL/CSA SJTow-A with ECS No.

3 250 cap plug with grounding pin 20 Ft. Length Rated 15 Amp 125V NEMA 5-15 PAutomatic Float SwitchMechanical Float* ITEM NO. Optima-3AS1 Impeller material is Thermo Plastic-Noryl GFN2** Optima-3 & EPD-3 1/3HP Shaft Seal is single mechanical seal (lower side) and 1 lip seal (upper side) Mechanical Seal material: Carbon/Ceramic/FPMEBARA Submersible Stainless Steel PumpsOptima/EPDS pecificationsProject:Model:Chk d:Date:EBARAF luid (803) 327-5005 (803) 327-5097 (fax)rev. 09/08 Model Optima-3MS1 EPD-3MS1 EPD-5 to 15 Manual Operation PumpsPerformance: ISO 2548 StandardOptionalDischarge Size1/3HP 11/4inch1/2HP through 11/2HP 11/2inchRange of HP1/3, 1/2, 3/4, 1, and 11/2 HPRange of PerformanceCapacity to 86 GPMHead to 61 feetLimitationMaximum Water Temperature122 F/50 C (140 F/60 C intermittent duty)Solids3/8'' Spherical (2% by concentration)Synchronous Speed3600 RPMM aterialsCasing304L Stainless SteelImpeller304L Stainless Steel *Shaft303 Stainless SteelMotor Frame304L Stainless SteelFasteners304L Stainless SteelShaft Seal(Double)

4 **Material UpperNBR Fitted Carbon/Ceramic 1/2, 3/4, 1, and 11/2 HPMaterial LowerFPM Fitted Silicon Carbide/Silicon Carbide 1/2, 3/4, 1, and 11/2 HPImpeller TypeSemi-OpenBearingSealed Ball BearingMotorAir-filled, Insulation Class F, 2 Pole, Rated Continuous Duty Permanent Split CapacitorSingle Phase115 VThree Phase230V or 460 VMotor Protection Built-in Motor Protection with Auto ResetPower CordSingle PhaseUL/CSA SJTOW-A with ECS No. 250 capplug with grounding pin 20 Ft. Length Rated 15 Amp 125V NEMA 5-15 PThree PhaseUL/CSA STOW-A water resistant, stripped endjacket removed 2'' and conductor stripped 5/8'' 20 Ft. length * ITEM NO. Optima-3MS1 Impeller material is Thermo Plastic-Noryl GFN2** Optima-3 & EPD-3 1/3HP Shaft Seal is single mechanical seal (lower side) and 1 lip seal (upper side) Mechanical Seal material: Carbon/Ceramic/FPM Three Phase models require user to provide motor protectionEBARA Submersible Stainless Steel PumpsOptimaSample SpecificationsProject:Model:Chk d:Date:EBARAF luid (803) 327-5005 (803) 327-5097 (fax)rev.

5 09/081. Scope of supplyFurnish and install EBARA Model_____Submersible Stainless Steel Pump(s). Each unit shall be rated at ____ GPMat ____ feet pump(s) shall be designed to pump dirty waters containing 3/8'' spherical solids without damage during pump(s) shall be designed so that the pump shaft horsepower (BHP) shall not exceed motor rated horsepower throughout the entire operating range of the pump performance curve. Pump(s) shall be built to operate whether fully or partially Casing and impellerMajor parts of the pumping unit shall be manufactured of Stainless Steel . The casing, motor frame, and fasteners shall be manufactured of 304 Stainless Steel .

6 The impeller and diffuser material shall be Thermo Plastic-Noryl GFN(2).The impeller shall be semi-open design. The pump(s) shall have a discharge size of 11/4'' Shaft sealThe pump(s) shall be furnished with a single mechanical and a single lip seal (rubber).4. MotorThe pump motor shall be 1/3HP, , 115 Volt, 60Hz, single phase. Motor shall be air filled with Class F insulation and shall be of split capacitor design. The motor shall be supplied with built-in thermal protection with automatic reset and shall be rated for continuous duty. Motor shaft shall be 303 Stainless Motor cablePump motor cable shall be suitable for Submersible pump applications.

7 Cable shall have 20 feet UL/CSA approved water resistant #16 AWG OptionA mechanical, non-mercury float switch is available in Pumps with automatic Submersible Stainless Steel PumpsEPD 1/3 HPSample SpecificationsProject:Model:Chk d:Date:EBARAF luid (803) 327-5005 (803) 327-5097 (fax)rev. 09/081. Scope of supplyFurnish and install EBARA Model _____Submersible Stainless Steel Pump(s). Each unit shall be rated at _____ GPMat ____ feet pump(s) shall be designed to pump dirty waters containing 3/8'' spherical solids without damage during pump(s) shall be designed so that the pump shaft horsepower (BHP) shall not exceed motor rated horsepower throughout the entire operating range of the pump performance curve.

8 Pump(s) shall be built to operate whether fully or partially Casing and impellerMajor parts of the pumping unit shall be manufactured of Stainless Steel . The casing, impeller, motor frame, and fasteners shall be manufactured of 304 Stainless Steel . The impeller shall be semi-open design. The pump(s) shall have a discharge size of 11/4'' Shaft sealThe pump(s) shall be furnished with a single mechanical and a single lip seal (rubber).4. MotorThe pump motor shall be 1/3HP, , 115 Volt, 60Hz, single phase. Motor shall be air filled with Class F insulation and shall be of split capacitor design. The motor shall be supplied with built-in thermal protection with automatic reset and shall be rated for continuous duty.

9 Motor shaft shall be 303 Stainless Motor cablePump motor cable shall be suitable for Submersible pump applications. Cable shall have 20 feet UL/CSA approved water resistant #16 AWG OptionA mechanical, non-mercury float switch is available in Pumps with automatic Submersible Stainless Steel PumpsEPD 1/2- 11/2 HPSample SpecificationsProject:Model:Chk d:Date:EBARAF luid (803) 327-5005 (803) 327-5097 (fax)rev. 09/081. Scope of supplyFurnish and install EBARA Model _____Submersible Stainless Steel Pump(s). Each unit shall be rated at _____ GPMat ____ feet pump(s) shall be designed to pump dirty waters containing 3/8'' spherical solids without damage during pump(s) shall be designed so that the pump shaft horsepower (BHP) shall not exceed motor rated horsepower throughout the entire operating range of the pump performance curve.

10 Pump(s) shall be built to operate whether fully or partially Casing and impellerMajor parts of the pumping unit shall be manufactured of Stainless Steel . The casing, impeller, motor frame, and fasteners shall be manufactured of 304 Stainless Steel . The impeller shall be semi-open design. The pump(s) shall have a discharge size of 11/2'' Shaft sealThe pump(s) shall be furnished with a double mechanical MotorThe pump motor shall be ___ HP, ___ , 60Hz, single phase. Motor shall be air filled with Class F insulation and shall be of split capacitor design. The motor shall be rated for continuous duty. Motor shaft shall be 303 Stainless Motor cablePump motor cable shall be suitable for Submersible pump applications.