Fire Safety - Fire Alarm Resources

1 P/N 315-090854-14 OPERATIONThe Model CSM-4 ControllableSignal Module has two fully supervised,programmable circuits. The outputs supplytwo Class B (Style Y) or Class A (Style Z)output circuits for the supervision and controlof audible or visual notification devices suchas horns, bells, strobes, notification circuit on a CSM-4 can beconfigured in one of three ways: (1) as asupervised connection to a Municipal Tie,(2) as a connection to a Leased Line remotemonitoring System, or (3) for releasing serviceper NFPA 12A, NFPA 13, and NFPA output can be controlled automaticallythrough the MXL program logic or manuallyby using the MXL keypad. Automatic controlcan also be time based. Each output can bemanually armed or disarmed through the MXLkeypad.

2 When any output is disarmed, theMXL LCD annunciator indicates which circuitor output, and the PARTIAL SYSTEM DIS-ABLE LED lights until the circuit or output isarmed again. The TROUBLE LED also CSM-4 notification appliance circuitsfunction in a Degrade mode, even when themain MXL processor or the network communi-cation link fails. Each circuit s degrade mode ofoperation can be separately configured to re-spond to an Alarm in any of the following ways:OFFON CONTINUOUSLY1 SECOND ON 1 SECOND OFF (Infinite repeat)CSM-4 notification appliance circuit outputscan be set by using the CSG-M for any oneof the following: (1) coded march time, (2) zonecode, or (3) uniform Code 3 CSM-4 has two diagnostic and two userprogrammable LEDs (See Figure 1).

3 In addition,each circuit is equipped with transient andnoise remove power before CSM-4 module plugs into one slot on theMOM-4 Expansion Module. There are fouravailable slots for the CSM-4 on the MOM-4 (SeeFigure 2). Selecting which position on the MOM-4to use for a CSM-4 determines which contactsare available: TB1, TB2, TB3, or CSM-4 is shipped with one card guide toadd to the MOM-4 before the CSM-4 can be in-stalled. Choose the position for the card guideaccording to which terminal block you wish to InstructionsModel CSM-4 Controllable Signal ModuleFire SafetySiemens Building Technologies, Fernwood RoadFlorham Park, New Jersey 07932 Siemens Building Technologies, Kenview BoulevardBrampton, Ontario L6T 5E4 CN2 Figure 1 CSM-4 BoardFigure 2 CSM-4 Installation Slots3To install the card guide, loosen the appropri-ate screw in the center area of the MOM-4 andset the card guide in place, making sure that thelocating pin on the bottom of the card guide is inthe hole on the MOM-4 (See Figure 4).

4 Tightenthe screw on the MOM-4 to secure the cardguide in Installing the CSM-4 Signal Module(Refer to Figure 3.) Before installing the CSM-4in the MOM-4, you must set the Network address,configure each circuit according to the CSG-Mprogram [as audibles (NACs), municipal tie,leased line, or releasing service (NFPA 12A,NFPA 13, and NFPA 2001)], and set the degrademodes (trouble and Alarm ) as follows:Note: To open a dipswitch, press down onthe side of the dipswitch marked close a dipswitch, press down onthe side of the dipswitch opposite theside marked open a slide switch, push the slideto the side opposite the side marked close a slide switch, push the slideto the side marked the Network addressThe Network address is set on switch S1 (SeeFigure 1).

5 See the CSG-M printout for the properaddress. Use Table 1 to set the the Mode of Operation for Each CircuitThe CSM-4 has one programming slide switchand one jumper for each of its two circuits. (Seeslide switches S3 and S4 and jumpers G1 andG2 on the board.) Setting these slide switchesand jumpers allows the selection of four possiblemodes of operation. These modes correspondwith NFPA standards 72 Local (notificationappliance circuit), Municipal Tie (municipal tie),Remote Station (leased line), and NFPA 12A,NFPA 13, and NFPA 2001 (releasing service).Each circuit on the CSM-4 can be set indepen-dently for the type of operation desired. Table2 shows how to set the switches and jumpersfor circuits 1 and 2. The CSG-M printout showsthe mode for each the Degrade Modes of OperationThere are two sources of degrade activation, thedegrade Alarm bus and the degrade trouble two buses become active ONLY whenthe MXL communication network fails.

6 SwitchS2 on the CSM-4 sets the degrade mode ofoperation for each Installing the CSM-4 Figure 3 Preparation for Installation41 ELBATGNIMMARGORPSSERDDAKROWTENRDDA123456 78 RDDA12345678 RDDA12345678 RDDA123456780001002003004005006007008009 0001011021031041051061071081091002012022 0320420520620720820920030130230330430530 6307308309300401402403404405406407408409 4005015025035045055065075085095006016026 0360 LAGELLILAGELLILAGELLIXXOOOOOOOOXOOOOOXOX OOOOOOXXOOOOOXXXOOOOOOOOXOOOOXOOXOOOOOXO XOOOOXXOXOOOOOOXXOOOOXOXXOOOOOXXXOOOOXXX XOOOOOOOOXOOOXOOOXOOOOXOOXOOOXXOOXOOOOOX OXOOOXOXOXOOOOXXOXOOOXXXOXOOOOOOXXOOOXOO XXOOOOXOXXOOOXXOXXOOOOOXXXOOOXOXXXOOOOXX XXOOOXXXXXOOOOOOOOXOOXOOOOXOOOXOOOXOOXXO OOXOOOOXOOXOOXOXOOXOOOXXOOXOOXXXOOXOOOOO XOXOOXOOXOXOOOXOXOXOOXXOXOXOOOOXXOXOOXOX XOXOOOXXXOXOOXXXXOXOOOOOOXXOOXOOOXXOOOXO OXXOOXXOOXXOOOOXOXXOOXOXOXXOOOXXOXXOOXXX OXXOOOOOXXXOOXOOXXXOOOXOXXXOOXXOXXXOOOOX XXXOOXOXXXXOOOXXXXXOOXXXXXXOO46056066076 0860960070170270370470570670770870970080 1802803804805806807808809800901902903904 9059069079089099000110120130140150160170 1801901011111211311411511611711811911021 121221321421521621721

7 OOOOOOXOXOOOOOXOOXOOOOXOXXOOOOXOOOXOOOXO XOXOOOXOOXXOOOXOXXXOOOXOOOOXOOXOXOOXOOXO OXOXOOXOXXOXOOXOOOXXOOXOXOXXOOXOOXXXOOXO XXXXOOXOOOOOXOXOXOOOXOXOOXOOXOXOXXOOXOXO OOXOXOXOXOXOXOXOOXXOXOXOXXXOXOXOOOOXXOXO XOOXXOXOOXOXXOXOXXOXXOXOOOXXXOXOXOXXXOXO OXXXXOXOXXXXXOXOOOOOOXXOXOOOOXXOOXOOOXXO XXOOOXXOOOXOOXXOXOXOOXXOOXXOOXXOXXXOOXXO OOOXOXXOXOOXOXXOOXOXOXXOXXOXOXXOOOXXOXXO XOXXOXXOOXXXOXXOXXXXOXXOOOOOXXXOXOOOXXXO OXOOXXXOXXOOXXXOOOXOXXXOXOXOXXXOOXXOXXXO XXXOXXXOOOOXXXXOXOOXXXXOOXOXXXXOXXOXXXXO OOXXXXXOXOXXXXXOOXXXXXXOXXXXXXXO82192103 1131231331431531631731831931041141241341 4415416417418419410511512513514515516517 5185195106116126136146156166176186196107 1171271371471571671771871971081181281381 481581681781881981091191 OOOOOOOXXOOOOOOXOXOOOOOXXXOOOOOXOOXOOOOX XOXOOOOXOXXOOOOXXXXOOOOXOOOXOOOXXOOXOOOX OXOXOOOXXXOXOOOXOOXXOOOXXOXXOOOXOXXXOOOX XXXXOOOXOOOOXOOXXOOOXOOXOXOOXOOXXXOOXOOX OOXOXOOXXOXOXOOXOXXOXOOXXXXOXOOXOOOXXOOX XOOXXOOXOXOXXOOXXXOXXOOXOOXXXOOXXOXXXOOX OXXXXOOXXXXXXOOXOOOOOXOXXOOOOXOXOXOOOXOX XXOOOXOXOOXOOXOXXOXOOXOXOXXOOXOXXXXOOXOX OOOXOXOXXOOXOXOXOXOXOXOXXXOXOXOXOOXXOXOX XOXXOXOXOXXXOXOXXXXXOXOXOOOOXXOXXOOOXXOX OXOOXXOXXXOOXXOXOOXOXXOXXOXOXXOXOXXOXXOX XXXOXXOXOOOXXXOXXOOXXXOXOXOXXXOXXXOXXXOX OOXXXXOXXOXXXXOXOXXXXXOXXXXXXXOX29139149 1591691791891991002102202302402502602702 8029020121122123124125126127128129120221 2222232242252262272282292203213223233243 2532632732832932042142242342442542642742 842942052152252352452552

8 OOOOOOXXXOOOOOXXOXOOOOXXXXOOOOXXOOXOOOXX XOXOOOXXOXXOOOXXXXXOOOXXOOOXOOXXXOOXOOXX OXOXOOXXXXOXOOXXOOXXOOXXXOXXOOXXOXXXOOXX XXXXOOXXOOOOXOXXXOOOXOXXOXOOXOXXXXOOXOXX OOXOXOXXXOXOXOXXOXXOXOXXXXXOXOXXOOOXXOXX XOOXXOXXOXOXXOXXXXOXXOXXOOXXXOXXXOXXXOXX OXXXXOXXXXXXXOXXOOOOOXXXXOOOOXXXOXOOOXXX XXOOOXXXOOXOOXXXXOXOOXXXOXXOOXXXXXXOOXXX OOOXOXXXXOOXOXXXOXOXOXXXXXOXOXXXOOXXOXXX XOXXOXXXOXXXOXXXXXXXOXXXOOOOXXXXXOOOXXXX OXOOXXXXXXOOXXXXOOXOXXXXXOXOXXXXOXXOXXXX XXXOXXXXLAGELLILAGELLILAGELLILAGELLILAGE LLILAGELLILAGELLILAGELLI)NOro(DESOLC=X)F FOro(NEPO=O5 Each circuit operates independently in thedegrade mode. Switch S2, positions SW1 andSW2, determine the degrade mode of operationwhen the trouble bus activates. S2, positionsSW3-SW6, determines the degrade mode ofoperation when the Alarm bus Trouble ActivationThe degrade trouble bus may ONLY be usedwhen the circuit is used as a leased linetrouble notification circuit (NFPA 72 RemoteStation).

9 (See Figure 3.) When enabled, thistrouble degrade mode ensures that a trouble istransmitted to the receiving station even whenthe MXL communication network 2 SETTING THE MODE OFOPERATION (USING S3, S4 AND G1, G2)*TABLE 3 SETTING THE DEGRADETROUBLE MODES ON S2 For Circuit 1SW1 Leased Line TroubleOn (Closed)No Trouble ActivationOff (Open)For Circuit 2SW2 Leased Line TroubleOn (Closed)No Trouble ActivationOff (Open)Note: If circuit 1 or circuit 2 is not used forleased line trouble, dipswitchesSW1 or SW2 must be off (open).For Circuit 1S3 PositionG1 Audibles [NAC] (NFPA 72 Local)Municipal Tie (NFPA 72)Leased Line (NFPA 72 Remote Station)Releasing Service (NFPA 12A)**Releasing Service (NFPA 13)**Releasing Service (NFPA 2001)**Illegal (Results in a trouble on the CSM-4)1121112 Not CutCutNot CutCutCutCutCutFor Circuit 2S4 PositionG2 Audibles [NAC] (NFPA 72 Local)Municipal Tie (NFPA 72)Leased Line (NFPA 72 Remote Station)Releasing Service (NFPA 12A)**Releasing Service (NFPA 13)**Releasing Service (NFPA 2001)**Illegal (Results in a trouble on the CSM-4)1121112 Not CutCutNot CutCutCutCutCut * See Figure 1.

10 ** CANADA ONLY: Do not cut jumpers G1 and G2 for NFPA 12A, NFPA 13, and NFPA 4 SETTING THE DEGRADE Alarm MODES ON S2 For Circuit 1SW4SW3 OFF (no degrade activation)Off (Open)Off (Open)CONTINUOUS (active on degrade Alarm )Off (Open)On (Closed)1 SEC. ON, 1 SEC OFF (infinite repeat)On (Closed)Off (Open)DO NOT USEOn (Closed)On (Closed)For Circuit 2SW6SW5 OFF (no degrade activation)Off (Open)Off (Open)CONTINUOUS (active on degrade Alarm )Off (Open)On (Closed)1 SEC. ON, 1 SEC OFF (infinite repeat)On (Closed)Off (Open)DO NOT USEOn (Closed)On (Closed)Note:When circuits are used for leased line supervisory, the Alarm degrade modesmust be set to OFF (Open).6 Using the CSG-M printout, determine if either ofthe circuits is configured as a leased line 3 shows how to set S2 (SW1 and SW2) toenable the degrade trouble activation for thedesired Alarm ActivationEach circuit on the CSM-4 can be set with switchS2, positions SW3-SW6, to determine when thedegrade Alarm bus activates.