FCM-1 Supervised Control Module - Fire Alarm …

1 Relay Contact Ratings: INSTALLATION AND MAINTENANCE INSTRUCTIONS. CURRENT RATING MAXIMUM VOLTAGE LOAD DESCRIPTION APPLICATION. 12 Clintonville Rd 3A 30 VDC Resistive Non Coded FCM-1 Supervised Control Module Northford, CT 06472-1653. (203) 484-7161. 2A 30 VDC Resistive Coded Specifications .9 A 110 VDC Resistive Non Coded Normal Operating Voltage: 15 to 32 VDC..9 A 125 VAC Resistive Non Coded Maximum Current Draw: mA (LED on). Average Operating Current: 390 A (LED flashing)..5 A 30 VDC Inductive (L/R=5ms) Coded External Supply Voltage: (between Terminals T3 and T4). 1A 30 VDC Inductive (L/R=2ms) Coded Maximum: 80 Volts (RMS or DC). Drain on External Supply: 2 mA Maximum (using internal EOL relay)..5 A 125 VAC Inductive (PF=.35) Non Coded Temperature Range: 32 F to 120 F (0 C to 49 C)..7 A 75 VAC Inductive (PF=.)

2 35) Non Coded Humidity: 10% to 93% Noncondensing Dimensions: 41/2 H x 4 W x 11/4 D (Mounts to a 4 square by 21/8 deep box.). Accessories: SMB500 Electrical Box; CB500 Barrier WARNING. All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed) state during Before Installing 2. Set the address on the Module per job drawings. shipping. To ensure that the switch contacts are in their correct state, modules must be made to communicate with the panel before This information is included as a quick reference installation Note: Some panels support extended addressing. In order to connecting circuits controlled by the Module . guide. Refer to the Control panel installation manual for detailed set the Module above address 99 on compatible systems, care- system information.

3 If the modules will be installed in an existing fully remove the stop on the upper rotary switch with thumb operational system, inform the operator and local authority that in the direction shown in Figure 1A. the system will be temporarily out of service. Disconnect power 3. Secure Module to electrical box (supplied by installer), as to the Control panel before installing the modules. shown in Figure 2A. NOTICE: This manual should be left with the owner/user of this IMPORTANT: When using the FCM-1 for fire fighter telephone equipment. applications, remove Jumper (J1) and discard. The Jumper is General Description located on the back under the product label as shown in Figure FCM-1 Supervised Control Modules are intended for use in intel- 1B. ligent, two-wire systems, where the individual address of each Figure 1A.

4 Removing Figure 1B. Jumper location: Module is selected using the built-in rotary switches. This Module rotary switch stop: is used to switch an external power supply, which can be a DC. power supply or an audio amplifier (up to 80 VRMS), to notifica- tion appliances. It also supervises the wiring to the connected loads and reports their status to the panel as NORMAL, OPEN, or 9 0. SHORT CIRCUIT. The FCM-1 has two pairs of output termination 8 4. 5. 67 8 9. 10. 11 1. 3 12 BACK OF LABEL. points available for fault-tolerant wiring and a panel-controlled 7. 2. 1 0 15 14. 13. 2. Module . TENS. LED indicator. This Module can be used to replace a CMX-2 mod- 6 4. 5. 6 7 8 9. 3. 3. ule that has been configured for Supervised wiring operation. 5 2. 10. 4. ONES. LOOP ADDRESS. Compatibility Requirements A78-2318-07 A78-2318-18.

5 To ensure proper operation, this Module shall be connected to a compatible Notifier system Control panels only (list available from J1 UNDER LABEL. Notifier). Figure 2A. Module mounting with barrier: Mounting The FCM-1 mounts directly to 4 square electrical boxes (see Figure 2A). The box must have a minimum depth of 21/8 . Surface mounted electrical boxes (SMB500) are available. Wiring NOTE: All wiring must conform to applicable local codes, ordi- Figure 2B: nances, and regulations. When using Control modules in nonpower limited applications, the CB500 Module 8. 9. 4 5 6 78. Barrier must be used to meet UL requirements for the 7 3. 9 9. 8 6 TEN 21. S 0. 10 0. LO 1211. 7 TE 2. 3. 4 5 6 78. 9. 0. OP 5 3. 15. 4 5 6 7 8 14 13 1. LO 6 NS 1. 0 15. 10. 1211 ON 2 9 2. OP 5 4 5 6 7 8 14 13 1 ES 1. 3.

6 Separation of power-limited and nonpower-limited termi- 3. ON 2 9 2 0. ES 1. 0. AD 4. 3 AD. DR 4. DR ES. ES. S. S. nals and wiring. The barrier must be inserted into a 4. x4 x21/8 junction box, and the Control Module must be placed into the barrier and attached to the junction box ISOLATED. QUADRANT. (Figure 2A). The power-limited wiring must be placed into the isolated quadrant of the Module barrier (Figure 2B). A78-2611-11. 1. Install Module wiring in accordance with the job drawings and appropriate wiring diagrams. A78-2610-08. N500-46-00 4 I56-1169-07 N500-46-00 1 I56-1169-07. 2001 Notifier Figure 3. Typical notification appliance circuit configuration, NFPA Style Y: Figure 5. Typical wiring for speaker supervision and switching, NFPA Style Y: COMMUNICATION LINE WIRES MUST BE Supervised PER NFPA.

7 CONNECT MODULES TO LISTED COMPATIBLE COMMUNICATION LINE 32 VDC MAX. NOTIFIER Control PANELS ONLY ALL WIRING SHOWN IS Supervised AND POWER LIMITED. 32 VDC MAX. ALL WIRING SHOWN IS Supervised . TWISTED PAIR. CONNECT MODULES TO LISTED COMPATIBLE. CONNECT MODULES TO LISTED COMPATIBLE. TWISTED PAIR IS RECOMMENDED. NOTIFIER. NOTIFIER Control . Control PANELS. PANELS ONLY. ONLY. )-( IS RECOMMENDED )-(. TO NEXT FROM PANEL OR TO NEXT ) ( ) (. )+( )+( )+( FROM PANEL OR. DEVICE PREVIOUS DEVICE DEVICE )+( PREVIOUS DEVICE. Control SPEAKER SWITCHING CIRCUIT - NFPA STYLE W Control . SPEAKERS MUST BE LISTED FOR FIRE PROTECTION. REFER Module . Module AUDIO CIRCUIT. 24 VDC CIRCUIT TO THE RELAY CONTACT RATING TABLE FOR MAXIMUM LOAD. DO NOT LOOP WIRE AROUND TERMINALS. DO NOT LOOP WIRE ON TERMINALS 3 & 4. BREAK WIRE TO ENSURE.

8 3 & 4. BREAK WIRE RUN TO PROVIDE 9. 5. 67 8 9. 10. 0 ) ( SUPERVISION OF CONNECTIONS. 8 4 11 1. Module POLARITIES ARE SUPERVISION OF CONNECTIONS. ) ( ) ( 3. 2. 12. 13 )+(. 9 67 8 9. 0. )-( 47 K EOL. 7 TENS. 1 0 15 14 2. ) (. AUDIO AMPLIFIER, Vrms MAX. 6789. SHOWN IN Alarm 6 5. 5 10 4 3. 8 4 11 1 RESISTOR 5. 3. 4. USE ONLY MODELS AA-30, AA100 OR AA-120. AMPLIFIER. 2. )-( )-(. 3. 2. 12. 13 )+( ONES. 10. )+(. 7 24 VDC POWER SUPPLY. ADDRESS. 1 0 15 14 2 ELR-47K. LOOP. TENS. 6789 )-( MUST PROVIDE WIRING SUPERVISION PER NFPA. 47K EOL 6 4. 5. 3. ISOLATED, REGULATED, POWER )+( )+( SUPERVISION. 5. 3. 2 4. )+( AUDIO CIRCUIT WIRING MUST BE TWISTED PAIR AS A MINIMUM. RESISTOR ONES. 10. LIMITED PER NFPA 70. ELR-47K. LOOP ADDRESS. SEE NOTIFIER INSTALLATION MANUAL FOR DETAILED INFORMATION. LISTED FOR FIRE PROTECTION WITH.

9 BATTERY BACKUP. WHEN A AUDIO AMPLIFIER IS USED, TERMINALS 1 AND 2 ARE POWER LIMITED, )+( )+( WHILE TERMINALS 3-9 ARE NONPOWER LIMITED. IN THIS CASE THE CB500 BARRIER. Module POLARITIES ARE TO NEXT Control Module . UL LISTED EOL RELAY LAST Module MUST RETURN. IS REQUIRED. OTHERWISE, ALL TERMINAL WIRING IS POWER LIMITED. THE CB500. SHOWN ENERGIZED SHOWN IN Alarm INCLUDES A LABEL INDICATING WHICH TERMINALS ARE NONPOWER LIMITED. THIS. TO NEXT Control Module OR END-OF-LINE-RELAY. WIRES FOR SUPERVISION. 24 VDC COIL LABEL MUST BE PLACED OVER THE POWER-LIMITED TERMINAL INFORMATION ON. A77-716-02. A77-716B ONE RELAY REQUIRED FOR EACH CIRCUIT. THE NAMEPLATE LABEL, PRESENT ON THE Module HOUSING. SOME Control PANELS HAVE RELAY BUILT IN AND. DO NOT REQUIRE EXTERNAL WIRING. REFER TO A78-2282-12 A78-2284-11.

10 NOTIFIER MANUAL. Figure 4. Typical fault tolerant notification appliance circuit configuration, NFPA Style Z: Figure 6. Typical fault tolerant wiring for speaker supervision and switching, NFPA Style Z: COMMUNICATION LINE WIRES MUST BE Supervised PER NFPA. COMMUNICATION LINE 32 VDC MAX. ALL WIRING SHOWN IS Supervised ALL WIRING SHOWN IS Supervised . TWISTED PAIR. AND POWER LIMITED 32 VDC MAX. CONNECT MODULES TO LISTED COMPATIBLE IS RECOMMENDED CONNECT MODULES TO LISTED COMPATIBLE. TWISTED PAIR NOTIFIER Control PANELS ONLY NOTIFIER Control PANELS ONLY. IS RECOMMENDED TO NEXT ) ( ) (. FROM PANEL OR. ) ( ) ( )+( )+( PREVIOUS DEVICE. TO NEXT FROM PANEL OR DEVICE. )+( )+(. DEVICE PREVIOUS DEVICE. SPEAKER SWITCHING CIRCUIT - NFPA STYLE X Control . Control SPEAKERS MUST BE LISTED FOR FIRE PROTECTION.