GUIDE TO ESTIMATING - Shop Solutions

1 CEDGUIDE TOESTIMATING1-800-4A-MOTOR(1-800-426-686 7) Collision ESTIMATING DataGENERALINFORMATIONINDUSTRYDEFINITION SSPECIALPRECAUTIONSLABOR PROCEDURESMOLDINGS, STRIPETAPE & DRILL TIMESREFINISHINGPROCEDURESQUARTER PANELREFINISHING NOTESAdd for stone guard if required. See GUIDE to quarter panelexterior surface &pockets .. pillar .. OPERATIONSR&R quarter panelwith roof offdeduct .. 11-17 OPERATIONSR&I trim panel .. 11-17 OPERATIONSSctn qtr panelcut in window opening11-17 AND R&R OPERATIONSQUARTER PANEL & COMPONENTS1 Outer panel ..(p )11-17 8990(p )11-17 10002 Lower pillar ..(p .5)11-17 4360(p.)

2 5)11-17 43703 Fuel door ..(p .5) 1050 Belt Molding4at window ..11-17 700011-17 7010 Molding5rear vertical ..11-17 RA 780011-17 LA 78106 Body side mldg11-17 # 136011-17 # 13707 Wheel opng(d .2)11-17 5080mldg(d .2)11-17 5090# PARTS: Order by model & color. LABOR: Time includes R&I quarter TO ESTIMATINGF ootnotes found in a chapter contain vehicle-specific information. The content of footnotes is in addition to, and takes precedence over, information in the GUIDE to ESTIMATING pages for the operation 8-17 Text Explanation GuideText Explanation GuideTie rod end ..11-17RD DescriptionYear CoverageSide of ApplicationR=RightL=LeftB=BothRight or Part PriceComponentClassification.

3 S = structuralm = Part Number PrimaryGroup HeadingIllustratedPart Call-OutNumberAdditionalRefinishingInfor mationR&I OperationsPaint OperationTimeFootnoteSymbol &DefinitionDrillingOperation TimeManufacturer sSpecial MarketingDesignation(see PARTS PRICES General Information page)Basic Sub-Group R&R = R&IIndicator(see R&I (Remove &Reinstall IndustryDefinition page)R&R = R&I IndicatorR&R Operation TimePrice StatusD=DiscontinuedC=Part price is less core chargeA=Special marketing programOperation times reported herein are compiled from availablemanufacturer data, as well as our own evaluation of shop data andare published only as an ESTIMATING GUIDE to ESTIMATING provides the guidelines that apply toMOTOR Crash ESTIMATING Data.)

4 Knowledge and application ofthese guidelines will assist the estimator in developing a clear esti-mate, reflecting as accurately as possible the requirements to per-form operations listed. To maintain accuracy, estimators must fre-quently refer to these pages throughout the ESTIMATING PARTSThe phrase BOLTED-ON PARTS referenced in this publicationrefers to mechanically fastened components that are directlyattached to the component that is being replaced and includesbraces, brackets, mounts, shields, extensions, interior trim, fasteners may include bolts, nuts, screws, clips SEQUENCEL isted under each basic assembly are the related and compo-nent parts.

5 List the damage according to the basic assembly, tak-ing the basic item first. Then, starting from the outside of the vehi-cle and working inward, list everything attached to it which is dam-aged. By following this procedure, you will make a more instance, on an estimate involving front fender damage,inspect as shown:FendermoldingnameplateemblemFender LinerFOOTNOTESF ootnotes are used to present information specific to the indi-cated component or operation. Footnotes are not intended to beused in place of service repair PRICESP rices used in MOTOR Crash ESTIMATING Data are factory sug-gested list prices, as supplied to us by the manufacturer.

6 Dealersmay not be required to sell at this price and may be free to deter-mine their own prices. When a price is prefixed by the letter D itindicates that this part has been discontinued by the manufactur-er and for your convenience, we continue to publish the last avail-able price. When a part is prefixed by the letter C, this indicatesa core value assigned by the manufacturer has been deductedfrom the manufacturer s suggested retail price. When a price isprefixed by the letter A, it indicates a Special Marketing Motors Target Marketing Program: This program hasbeen discontinued by GM. Parts indicated with the letter A rep-resent components included in the program.

7 These parts do nothave a suggested list price supplied by General Motors. The priceshown following the letter A is an approximation which you mayfind helpful. These prices are to be regarded as a GUIDE only. Theactual price, which may be higher or lower than the publishedprice, can be determined by contacting the General Motors dealerin your Competitive Crash Parts Program: The prices for theseparts may carry a special discount. Actual price should be deter-mined by calling the dealer in your local area. Dealers are notrequired to participate in this program and are free to determinetheir own prices for these prices do not include cost of state and local taxes, bolts,rivets, screws, nuts, washers, clips, fasteners, paint/body repairmaterials and refinishing unless otherwise QUANTITIESMany procedures require replacement of parts such as fasten-ers (bolts, rivets, screws, nuts, clips, for example) or washers.

8 Theapplicable quantities for these parts are provided whenever possi-ble. This information will be provided as reported by the DIAGRAMSMOTOR includes underhood diagrams when available. Allmeasurements are in millimeters. Please refer to MOTOR CollisionRepair Data manual or MOTOR E-Frame Data on CD for completevehicle dimension specifications. All underhood illustrations usedherein are copyrighted by Hein-Werner Corporation, Milwaukee,Wisconsin and used with the permission of the copyright TO ESTIMATINGG3 REV. 8-17 GENERAL INFORMATIONADD IF REQUIREDMOTOR Collision ESTIMATING Data is based on the base modelvehicle configuration, standard or regular production options,and/or standard replacement operations.

9 "Add if required" opera-tions are for extra procedures necessitated by optional factoryequipment or certain collision scenarios that may be encountered."Add if required" operations should be added to the estimatewhenever applicable after an "on the spot" inspection of vehicledamage and/or vehicle CLASSIFICATIONThe purpose of classifying components is to describe physicalproperties of the component, and classifications may inform theestimator that specialized technician skill levels and/or tools maybe required. Indicators are not intended to determine labor ratescharged, or to be inclusive of all components.

10 Any additional com-ponent classification(s) should be determined after an on-the-spotevaluation of required repair INDICATORS ARE PROVIDED FOR YOUR CONVENIENCE AND MUST ONLY BE CONSIDERED A HELPFUL component classifications are defined as follows:(M) Mechanical:Components that transform one form ofmotion or energy into another. Mechanical components would like-ly be serviced at a mechanical service facility rather than a bodyrepair facility if that component failed during normal components will likely require a specialized technicianskill level and/or specialized tools.(S) Structural: Components that provide a load bearing foun-dation for the purpose of safety and/or stability (no classification) Body: Components that do not fall underthe mechanical or structural classificationD&R (Disconnect & Reconnect)Some labor procedures require disconnecting (unplug and/orunbolt) of a component/assembly at the point where it is attachedto the subject part.