Example: dental hygienist
Gyproc SoundBloc 12 - british-gypsum.com
Either cut the board with a plasterboard saw, or score the front face paper with a sharp knife, snap it over a straightedge, then cut the back face paper. Cut holes for things like socket boxes using a utility saw. Fixing Fix the board with the decorative side facing outwards to receive finishes. Install fixings at least 13mm from cut
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Identification
www.british-gypsum.comTable 1: Glasroc F FireCase fixings. Board thickness (mm) Min. fixing length Board-to-board fixing Board-to-metal fixing 15 Glasroc F FireCase Screws 40mm ... Gyproc plasterboard lining. Refer to construction detail 16 on page 3.14. – For further information please please refer to Technical Support on .
Gyproc Moisture Resistant - british-gypsum.com
www.british-gypsum.comGyproc Moisture Resistant Product Data Sheet Introduction Suitable as a base for tiling in wet use areas. Also used for external soffits in sheltered positions.
C05. S02. P02 – P30 ShaftWall - british-gypsum.com
www.british-gypsum.comC05 Introduction Specialist partitions Specialist partitions This section details specialist lightweight systems where high-security, curved, fire or …
C05. S05. P02 – P05 GypWall secure - british …
www.british-gypsum.comC05. S05. P02 – P05 GypWall secure Including C05. S01. P02 Specialist partitions introduction This section includes updated information, added since it was first
Robustness SYSTEM DESIGN PRINCIPLES
www.british-gypsum.comImportantly for design, the greatest rate of strength loss is in the range of 400°C to 600°C. Using fire design codes such as the Structural Eurocodes EC3-1.2 and EC4-1.2 (designated BS EN 1993-1-2 and BS EN 1994-1-2), the load on the structure at the time of the fire can be calculated by treating it as an accidental limit state.
GypCeiling MF - british-gypsum.com
www.british-gypsum.comRefer to construction detail 7, relating to double layer 12.5mm Gyproc SoundBloc linings. With concrete floors the high mass of the construction means that high levels of acoustic performance can be achieved when the GypCeiling MF ceiling is suspended by conventional means, i.e. Gypframe MF8 Strap Hangers or Gypframe FEA1 Steel Angle.
Product Data Sheet - british-gypsum.com
www.british-gypsum.comadditives for extra fire protection. Where to use. Use it in partitions, ceilings and steel encasement . systems to achieve the fire performance required in domestic separating walls, corridors, garages and steel encasements. Certifications. Environmental Product Declaration (EPD) available Click here. Product information. Composition
Related documents
6. INSTALLATION - Building and Construction Authority
bca.gov.sg• Plasterboard screws should be spaced i. <300mm for butt joints ii. <200mm for angles joints iii. 10 to 16mm from edges and ends of plasterboard sheets • Ensure securing process of the board onto the vertical stud does not cause tilting of flange. Application of drywall screws shall begin from centre outwards. • Install screws from ends
Guide to Standards and Tolerances (currently under review)
www.vba.vic.gov.au9.07 Covering movement control joints and damp-proof courses 49 9.08 Cracking in applied finishes used over lightweight substrate 49 9.09 Rendered surfaces 49 9.10 Cracking in external mouldings 50 9.11 Plasterboard sheeting 50 9.12 Other sheeting systems 50 9.13 Level of finish for plasterboard 50
Conventions for U-valuecalculations - BRE
www.bre.co.uk3.6 Gypsum plasterboard 5 3.7 Structural timber 5 3.8 Metals and alloys 5 3.9 Thermal conductivity of other materials 6 3.10 Reflective foil products 6 3.10.1 Bubble sheet with aluminium foil facing 6 3.10.2 Multi-foil insulation 6 4 Issues concerned with U-value calculations 7 4.1 Surface resistance 7 4.2 Mortar joints in masonry construction 7
THERMAL BRIDGING GUIDE - LABC
www.labc.co.ukjoints and wall-ties in masonry construction or timber or steel studs in framed construction. Where the frequency of these is known and consistent their effects can be accounted for directly in the U-value calculation for the building element itself. ... Plasterboard on plaster dabs