Example: dental hygienist
Horton RC4100 Installation - absupply.net
Confirm handing of door before installing operator. Refer to section 17 for instructions if changing hand of operator is required. See H-SW C4190 Set Up Instructions section 11 for wiring options and fire door requirements 3. OPERATOR HANDING EXTERIOR LH LHR Output shaft 1 1/2"(38) Required overlap at the jamb. 3/4" (19) CL Pivot Side Blocking ...
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
8000/8100 Series Swing Door Operator Installation Instructions
absupply.netAn extension adapter is included with each arm assembly, connecting the drive arm to the op-erator output shaft. This 20mm adapter mounts the drive arm approximately 1/2” below the bot-tom of the header. Optional adapters are available that will increase the distance from 1/2” to
Sliding Door Operator Besam SL500 T Installation and ...
absupply.netAddress: 1900 Airport Road, Monroe, NC 28110, US Type: Besam SL500 T 100 V AC -10% to 240 V AC +10% 50/60 Hz fuse 10 AT Mains power supply: Note: The mains power supply shall be installed with protection and an all-pole mains switch with isolating capability of Category III, at least 1/8" (3 mm) between contacts, shall be installed according to ...
DESIGN, INSTALLATION, REChARGE, AND MAINTENANCE …
absupply.netNOZZLES 2-11 RUBBER BLOW-OFF CAPS 2-11 SWIVEL ADAPTOR 2-11 NOZZLE AIMING DEVICE 2-12 HORN/STROBE ASSEMBLY 2-12 COMPONENTS LIST 2-13 3. SYSTEm DESIGN GENERAL 3-1 NOZZLE COVERAGE AND PLACEMENT 3-1 Duct Protection 3-1 Modularizing Duct 3-2 Transition Ducts 3-3 Electrostatic Precipitator 3-3 Plenum Protection 3-3 Appliance …
CROSS REFERENCE CHARTS DOOR CLOSERS CROSS ... - …
absupply.nettc4300 4040* 7500/7700 8916 sc71 na 351 p400 dc6000 na tc7000 na na rts-88 ohc100 608 na na na na tc7700 na na na na na na na na na global lcn norton dorma dor-o-matic rixson sargent yale corbin- arrow falcon russwin door closerscross reference [ 8 ] tc300 400 61/951 na na s40 na ev66 500 dc51 tc2200 700 90/680/780 850/880/980 ... tc200 series ...
CALCULATed dOOR WeIGHT TABLe - Hollow metal door and …
absupply.netHollow core 2.5 30 33 35 40 38 42 44 50 45 50 53 60 White pine 3.5 42 47 49 56 53 58 61 70 63 70 74 84 Fir 3.5 42 47 49 56 53 58 61 70 63 70 74 84 Solid core 4.3 51 57 60 68 64 71 74 85 77 85 89 102 Mahogany 4.5 54 60 63 72 68 75 79 90 81 90 95 108 Ash 5.0 60 67 70 80 75 83 88 100 90 100 105 120 Birch 5.5 66 73 77 88 83 92 96 110 99 110 116 132
FEBRUARY 212 KAWNEER 1686 EL CONCEALED EXIT DEVICE …
absupply.netkawneer.com ovement. 212 dwar efor. 743 3 FEBRUARY 212 KAWNEER 1686 EL CONCEALED EXIT DEVICE INSTALLA AR 38312 Lock Stile Fastener #12-24 x 1-1/4" PHMS Lock Stile Fastener #8-32 x 1-1/4" Cap Screw
R-102 RESTAURANT FIRE SUPPRESSION SYSTEM
absupply.netsuppression system will operate effectively and safely, mainte-nance must be conducted at six-month intervals, or earlier if the ... SYSTEM SELECTION GUIDE 9-1 – 9-4 SYSTEM COMPONENT INDEX 9-5 – 9-6.2 PARTS LISTS 9-7 – 9-10.2 MULTIPLE NOZZLE FRYER 9-11 PROTECTION CALCULATION
DOOR CONTROL AND SECURITY HARDWARE
absupply.netField convertible with parts. Fail Safe — FS FS — FAIL-SAFE electric strikes require ... Watt-seated @ 70°F 7.5 8 Amps-seated @ 70°F .6 .33 Amps-inrush @ 70°F .6 .33 DIMENSIONS AND CONFIGURATIONS ... 3042, 3061 and 3062. 6214 Electric strike for use with mortise locks
Related documents
DRYWALL GRID SYSTEMS - Armstrong Ceiling S
www.armstrongceilings.com23 Double Hung Ceilings 24 Triple Hung Ceilings 25 Exterior Wind Load Data 26-27 ®UL Fire Resistive 28 Seismic Installation Instructions 29 Load Data 30 Basic Products 31 Sound Control 32 Estimating • Rotary-stitched – Greater torsional strength and stability • 1-1/2" wide face main beams and cross tees – Easy installation
INSTALLATION INSTRUCTIONS for Pre-Hung Exterior …
images.thdstatic.comINSTALLATION INSTRUCTIONS for Pre-Hung Exterior Entry Doors (JII106) 4 1. Cut a piece of sheet material to the length shown. 2. Lightly crease folding lines 1/2" in from the two short sides and one long side. 3. Measure the distance from the back of the trim to the interior edge of the frame and add 9/16". 4. Take this distance from the back
INSTALLATION INSTRUCTIONS FOR INTERIOR PREHUNG …
images.thdstatic.comINSTALLATION INSTRUCTIONS FOR INTERIOR PREHUNG DOORS Make sure: 1. The threshold is level 2. The hinge side of the rough opening is plumb 3. The head is square to the hinge side of the rough opening Center the prehung unit into the rough opening, bottom first. When the door opens to you, and the knob is on the left, it is a left hand door. When ...
REPLACEMENT WINDOWS FOR DETAILED INSTALLATION …
www.simonton.com• Install installation screws in the pre-drilled installation holes in the head. After the window is secured, recheck the sash operation and weather seals. 8. Finish off the exterior of the window. Attach the sill extender (if necessary) to the bottom of the sill and trim it to fit in the opening.
Commercial Kitchen Hood Installation and Maintenance …
larkinhoods.comthe hood will be hung and prepare the structural support system using inserts, shields, angle iron, etc., and ½” threaded rod with turn buckles (hanging material by others). Verify that the materials used are sufficient to support the weight of hood and hanging system. (Refer to NFPA-96 for proper installation methods and materials.)
Installation Details - Wood and Aluminum-Clad Wood Exterior
media.pella.comInstallation Details - Wood and Aluminum-Clad Wood Exterior When to Use Fin Installation Method This installation is best for construction methods that will permit the unit to be installed from the exterior prior to the lap siding or other similar material. Products Available for This Installation All Pella aluminum-clad windows and doors.