Installation Guide

1 This product is intended for Installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and components. 2016 Directed. Vista, CA N4105 2016-02 Installation GuideKeyless Entry Remote Start4105 4-button seriesBitwriters with a date code of 6A or older require an IC upgrade (P/N 998M). Some Bitwriters with a date code of 6B do not require the IC upgrade, refer to Tech Tip #1112 for more information. Bitwriter , Code Hopping , Doubleguard , ESP , FailSafe , Learn Routine , Nuisance Prevention Circuitry, Revenger , Silent Mode , Soft Chirp , Stinger , Valet , and Warn Away are all Trademarks or Registered Trademarks of Directed .The Bitwriter (p/n 998U) requires chip version or newer to program this !

2 Safety First ..4 Wiring Diagram ..5 Wiring Connections ..5 Main (Primary) Harness, White 9-pin connector ..5 Door Lock - White 3 pin connector ..6 Heavy Gauge Relay, White 6-pin connector ..6 Satellite harness - White 4-pin connector ..6 Remote start harness, White 5-pin connector ..6D2D Harness, Red 4-pin connector ..6 Bitwriter/Directed SmartStart Harness, Black 3-pin Hardwired or Data Tach (not needed with Virtual Tach)..7 Initializing Virtual Tach (not needed w/hardwire and data tach inputs) ..7 Remote start Shutdown Diagnostics ..7 Programming system Features ..8 Feature Menus ..9 Menu 1 - Vehicle Integration & Convenience ..9 Menu 2 - Remote start ..10 Bitwriter Only Options ..12 Bitwriter feature descriptions ..12 Basic Remote Functions ..13 Reset And Deletion ..13 Pairing a Remote Control ..14 Troubleshooting: Keyless Entry.

3 14 Troubleshooting: Remote start ..144 2016 Directed. All rights ! Safety First The following safety warnings must be observed at all times: Due to the complexity of this system , Installation of this product must only be performed by an autho-rized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the re-mote start system must be disabled using the installed toggle switch.

4 It is the user s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this Installation Guide , (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the Parking Brake feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.

5 This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product Installation Guide . If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. After the remote start module has been installed, test the remote start module in accordance with the Safety Check outlined in this Installation Guide . If the vehicle starts when performing the Parking Brake Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or properly reinstalled so that the vehicle does not start in gear. All installations must be performed by an authorized Directed dealer. OPERATION OF THE REMOTE start MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS IN-TENDED MODE OF OPERATION.

6 OPERATING THE REMOTE start system UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE start MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR Installation OR REINSTALLATION ! This product is designed for fuel-injected, automatic transmission vehicles only. Installing it in a standard transmission vehicle is dangerous and is contrary to its intended 2016 Directed. All rights DiagramControl Button(Valet Button/Switch)Door Lock/unlockHarnessEnd ViewAntennaAntennaLED (Programmingindicator)Light ash polarity jumpersNote: This port may not be present on some modelsPrimary HarnessRemote start HarnessHeavyGaugeRelayEnd ViewSide ViewSide ViewTop ViewSatellite HarnessD2 DBitwriter/Directed SmartStartWiring ConnectionsMain (Primary) Harness, White 9-pin connector1 LIGHT GREEN/BLACK(-) 200mA FACTORY ALARM DISARM OUTPUT2 GREEN/WHITE(-) 200mA FACTORY ALARM REARM OUTPUT3 YELLOW(+) IGNITION OUT (TO ALARM) 4 WHITE/BLUE(-) ACTIVATION INPUT 5 ORANGE(-) 500mA GROUND WHEN LOCKED/ANTI-GRIND OUTPUT6 BROWN(-) 200mA HORN OUTPUT7 RED/WHITE(-) 200mA TRUNK RELEASE OUTPUT8 BLACK(-) CHASSIS GROUND9 WHITE(+/-) LIGHT FLASH OUTPUT6 2016 Directed.

7 All rights Lock - White 3 pin connector1 LIGHT BLUE(-) 200mA UNLOCK OUTPUT 2 EMPTYNOT USED3 GREEN (-) 200mA LOCK OUTPUT Heavy Gauge Relay, White 6-pin connector1 RED(+) 30A HIGH CURRENT 12V INPUT2 PINK/WHITEOUTPUT TO SECOND IGNITION/ACCESSORY CIRCUIT3 RED(+) 30A HIGH CURRENT 12V INPUT 4 ORANGE(+) ACCESSORY OUTPUT5 PURPLE(+) STARTER OUTPUT 6 PINK(+) IGNITION 1 INPUT/OUTPUT Satellite harness - White 4-pin connector1 BLUE(-) 200mA STATUS OUTPUT2 ORANGE(-) 200mA ACCESSORY OUTPUT3 PURPLE(-) 200mA STARTER OUTPUT4 PINK(-) 200mA IGNITION OUTPUTR emote start harness, White 5-pin connector1 BLACK/WHITE(-) PARKING BRAKE INPUT*2 VIOLET/WHITETACHOMETER INPUT 3 BROWN (+) BRAKE SHUTDOWN INPUT4 GRAY(-) HOOD PIN SWITCH SHUTDOWN INPUT5 BLUE/WHITE(-) 200mA 2ND STATUS/REAR DEFOGGER OUTPUTD2D Harness, Red 4-pin connector1 BLUED2D - TX2 BLACK(-) GROUND3 GREEND2D - RX4 RED(+) 12 VBitwriter/Directed SmartStart Harness, Black 3-pin connector1 RED(+) 12V2 ORANGEESP2 - RX/TX3 BLACK(-) GROUND* Connect this wire to one of the wires on the provided Remote start Shutoff Switch.

8 The other wire on the switch connects to the (-) Parking Brake wire in the vehicle. The switch must be in the ON position for the remote start to : NEVER connect 200mA low current outputs directly to a motor or high current device WITH-OUT a 2016 Directed. All rights Hardwired or Data Tach (not needed with Virtual Tach)To learn tach signal:1. start the vehicle with the Within 5 seconds, press and hold the Control Button (Valet).3. After 3 seconds the system LED will light solid when the tach signal is Release the Control Button (Valet).Important: This unit can learn the tachometer with the analog input or through D2D using an interface module. The unit confirms which source is used. When programming tach learning with: The analog Violet/White Tachometer input, the parking lights flash one time. A D2D inerface module, the parking lights flash the analog tachometer input on the system is connected to the vehicle, the D2D tachometer input will be Virtual Tach (not needed w/hardwire and data tach inputs)Note: Virtual Tach is not recommended for diesel program Virtual Tach:1.

9 After the install is complete, remote start the engine. The programming operation may require 3 cranks of the starter before the engine starts and runs. DO NOT turn off the remote start if this hap-pens, it is a normal programming Once the engine begins running, let it run for at least 30 Using the Remote, send the Remote start command to turn remote start OFF. Virtual Tach is pro-grammed. To reset Virtual Tach, (see the Reset and Deletion section of this Guide ). Virtual Tach cannot be reset with the Tach handles disengaging the starter motor during remote starting it does not address the customer wants to have the over-rev protection capability, the tach wire must be : After successfully learning Virtual Tach, a small minority of vehicle starters may over or under crank during remote start . The Bitwriter can be used fine tune the starter output time in 50mil-liseconds increments to compensate for such an start Shutdown DiagnosticsIf the remote start activates but fails to stay running, the remote start module has the ability to inform you of what may have caused the remote start failure.

10 Before performing shutdown diagnostics it is important that you let the remote start shut off on its own , let it attempt to start three times then shut down, if this is not done the unit will report the shutdown last used to shut off the remote perform shutdown diagnostics:1. With the ignition OFF, press and hold the Control Button. 2. Turn the ignition ON and then back Off while holding the Control Release the Control Press and release the Control 2016 Directed. All rights status LED flashes to report the last shutdown for one minute or until the ignition is turned ON, as shown in the following table:Status LED FlashesShutdown Mode1 flashTimed out2 flashesOver-rev shutdown3 flashesLow or no RPM, low battery (voltage and virtual tach modes) 4 flashesTransmitter shutdown (or optional push button)5 flashes(-) Hood shutdown (Remote start harness GRAY wire)6 flashes(+) Shutdown (Remote start harness BROWN wire) 7 flashesParking Brake shutdown (Remote start harness BLACK/WHITE wire)8 flashesWait-to- start timed outProgramming system FeaturesThe system Features Learn Routine dictates how the unit operates.