Installation Instructions - KitchenAid

1 If oven does not operate: Check that circuit breaker is not tripped or house fuse blown. See Use and Care Guide for troubleshooting you need assistance:If you have questions about operating, cleaning ormaintaining your oven: Refer to Use and Care Guide. Call the Consumer Assistance Center: Check your Use and Care Guide for a toll-free number to call or call the dealer from whom youpurchased this appliance. The dealer is listed in the Yellow Pages of your phone directory under Appliances Household Major Service and Repair. Part No. 8300654 2001 Printed in ReferenceTable of Contents:PagesProduct dimensionsCutout dimensionsBefore you startElectrical requirementsInstallation stepsIf you need assistance:Check your Use and Care Guide for a toll-free number to call or callthe dealer from whom you purchased this appliance.

2 The dealer islisted in the Yellow Pages of your phone directory under Appliances Household Major Service and Repair. Call when you: Have questions about built -in oven Installation or operation. Need to obtain the name and number of an authorized service you call, you will need: The built -in oven model number. The built -in oven serial numbers are listed on the model/serial rating plate, located onthe oven door or on the oven frame. 111223 IMPORTANT:Read and save these InstructionsIMPORTANT:Installer: Leave Installation Instructions with the : Keep Installation Instructions for future Installation Instructions for local electrical inspector's No.

3 830065430" Electric built -in Single andDouble OvensIf you need service:Maintain the quality built into your built -in oven bycalling an authorized service obtain the name and number of an authorizedservice company: Contact the dealer from whom you purchased your built -in oven; or Look in the Yellow Pages of your telephone directory under Appliances Household Major Service and Repair for an authorized service company; or Call the Consumer Assistance Center. The toll-free phone number is listed in your Use and Care you call, you will need: The built -in oven model number.

4 The built -in oven serial numbers are listed on the model/serial ratingplate, located on the oven door or on the 14 screws (double oven)PhillipsscrewdriverProduct dimensionsCutout dimensionsBefore you "recessedheight51" " max. recessed width23" ovenSingle oven27-1/2"recessedheight28-3/8" " " " " top of cutoutto bottom ofupper cabinetdoor30" width30" width28-1/2"cutoutwidth28-1/2"cutoutwidt h49-3/4" "bottomof cutoutto floor1-1/2" ofcutout to top ofcabinet door28-1/2"cutout width5-1/4" bottom ofcutout to floor27-3/4" " of cutoutto undersideof countertop1" top of cutoutto bottom ofupper cabinetdoor1-1/2" ofcutout totop ofcabinetdoor32"bottom ofcutout tofloorSingle ovenundercounter(without cooktop installed above)

5 Double ovenCabinet side viewSingle oven27-3/4" " depth23" recessedoven depthrecessed ovencabinetovenfrontImportant: Observe all governing codes and installationis your responsibility. Have a qualified technician install this oven. Oven locationshould be away from strong draftareas, such as windows, doors and strongheating opening dimensionsthat are shownmust be used. Given dimensions provideminimum clearance. Recessed Installation areamust providecomplete enclosure around the recessed portionof the groundis required. See Electricalrequirements.

6 Electrical supply junction boxshould be located3 inches maximum below the support surfacewhen oven is installed in a wall cabinet. Drill a 1-inch minimum diameter hole in the right rearor left rear corner of the support surface to passthe appliance cable through to the junction undercounter Installation , it is recommendedthat the junction box be located in the adjacentright or left cabinet. If installing the junction boxon rear wall behind oven, junction box must berecessedand located in the upper or lower rightor left corner of support surface MUST be solid, level andflush with bottom of cabinet of the standards listed may be obtained from:* National Fire Protection AssociationBatterymarch ParkQuincy, Massachusetts 02269 Tool needed:Parts supplied.

7 Cabinet filler kits are available from your a matching color kit if oven is smaller than yourcabinet oven filler height is 3-5/16"Black 4378941 White 4378942 Almond 4378943 Double oven filler height is 6-5/16"Black 4378947 White 4378948 Almond 437894929-3/4"overall width29-3/4"overall widthIt is the customer s responsibility:To contact a qualified electrical assure that the electrical Installation isadequate and in conformance with NationalElectrical Code, ANSI/NFPA 70 latest edition*,and all local codes and safety and the safety of others are very have provided many important safetymessages in this manual and on your read and obey all safety is the safety alert symbol.

8 This symbol alerts you to potential hazardsthat can kill or hurt you and others. All safety messages will follow the safety alertsymbol and either the word DANGER or WARNING . These words mean:All safety messages will tell you what the potentialhazard is, tell you how to reduce the chance ofinjury, and tell you what can happen if theinstructions are not can be killed or seriously injured if youdon t immediatelyfollow can be killed or seriously injured if youdon t follow 2 Electrical requirementsInstallation power supplyoff. Move oven close tofinal position.

9 Remove and discardshipping materials, tapeand protective film fromthe Notremove shipping baseor shipping feet at the front lower corners ofoven. The shipping feet will protect the loweroven trim until oven is inserted into cabinet. Remove and set aside racks and other partsfrom inside sidetrim sidetrim screws to attachoven to screws to attachoven to ovenframe to ovenframe to cableBpowersupply cableDo Notremoveshipping trim screws attaching right andleft side trim to oven. Grasp the bottom end oftrim and pull away from oven.

10 Slide top end oftrim downward to remove trim from oven. Takecare not to scratch other surfaces with ends oftrim. Set trim and screws aside on trim trim top of codes permit and a separate grounding wire isused, it is recommended that a qualified electriciandetermine that the grounding path and wire gaugeis in accordance with local Not ground to a gas with a qualified electrician if you are notsure oven is properly Not have a fuse in the neutral or groundingcircuit. A time-delay fuse or circuit breaker is recommended. Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with grounding wire).