Example: marketing

Installation Manual - - APC USA

Installation Manual 150 kVA power distribution Unit PDPB150G6F. 990-5235A-001. Publication Date: April 2015. Schneider Electric IT Corporation Legal Disclaimer The information presented in this Manual is not warranted by the Schneider Electric IT Corporation to be authoritative, error free, or complete. This publication is not meant to be a substitute for a detailed operational and site specific development plan. Therefore, Schneider Electric IT Corporation assumes no liability for damages, violations of codes, improper Installation , system failures, or any other problems that could arise based on the use of this Publication. The information contained in this Publication is provided as is and has been prepared solely for the purpose of evaluating data center design and construction.

Installation Manual 150 kVA Power Distribution Unit PDPB150G6F 990-5235A-001 Publication Date: April 2015 ... Exterior components Item Description Subfeed electrical plate Incoming power cover plate Locking latch for upper side panel Upper side panel

Tags:

  Manual, Installation, Electrical, Distribution, Power, Exterior, Installation manual, Power distribution

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Installation Manual - - APC USA

1 Installation Manual 150 kVA power distribution Unit PDPB150G6F. 990-5235A-001. Publication Date: April 2015. Schneider Electric IT Corporation Legal Disclaimer The information presented in this Manual is not warranted by the Schneider Electric IT Corporation to be authoritative, error free, or complete. This publication is not meant to be a substitute for a detailed operational and site specific development plan. Therefore, Schneider Electric IT Corporation assumes no liability for damages, violations of codes, improper Installation , system failures, or any other problems that could arise based on the use of this Publication. The information contained in this Publication is provided as is and has been prepared solely for the purpose of evaluating data center design and construction.

2 This Publication has been compiled in good faith by Schneider Electric IT Corporation. However, no representation is made or warranty given, either express or implied, as to the completeness or accuracy of the information this Publication contains. IN NO EVENT SHALL SCHNEIDER ELECTRIC IT CORPORATION, OR ANY PARENT, AFFILIATE OR. SUBSIDIARY COMPANY OF SCHNEIDER ELECTRIC IT CORPORATION OR THEIR RESPECTIVE. OFFICERS, DIRECTORS, OR EMPLOYEES BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL, OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR. LOSS OF BUSINESS, CONTRACT, REVENUE, DATA, INFORMATION, OR BUSINESS INTERRUPTION). RESULTING FROM, ARISING OUT, OR IN CONNECTION WITH THE USE OF, OR INABILITY TO USE THIS.

3 PUBLICATION OR THE CONTENT, EVEN IF SCHNEIDER ELECTRIC IT CORPORATION HAS BEEN. EXPRESSLY ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SCHNEIDER ELECTRIC IT. CORPORATION RESERVES THE RIGHT TO MAKE CHANGES OR UPDATES WITH RESPECT TO OR IN. THE CONTENT OF THE PUBLICATION OR THE FORMAT THEREOF AT ANY TIME WITHOUT NOTICE. Copyright, intellectual, and all other proprietary rights in the content (including but not limited to software, audio, video, text, and photographs) rests with Schneider Electric It Corporation or its licensors. All rights in the content not expressly granted herein are reserved. No rights of any kind are licensed or assigned or shall otherwise pass to persons accessing this information. This Publication shall not be for resale in whole or in part.

4 Contents Overview .. 1. Important Safety Information.. 1. Additional Safety Information .. 2. Before you begin .. 2. Operation and Adjustments .. 2. About This Manual .. 3. Related Documents.. 3. Product Related Information .. 3. User Comments .. 3. Component Identification .. 4. exterior components .. 4. Interior components .. 5. Installation .. 6. electrical Safety .. 6. SAVE THESE INSTRUCTIONS! .. 6. Space Considerations .. 6. Row Installation .. 7. Remove and install the side panels .. 7. Maintenance Bypass Panel Interface .. 8. Important information regarding derated units .. 9. Connect the Maintenance Bypass Panel to the PDU .. 9. Perform Equipotential Bonding .. 10. Connect and Level Enclosures .. 11. Prepare for power Cables.

5 12. Top or bottom cable entry .. 12. 150 kVA PDU i Main Installation .. 13. Connect the subfeed breaker .. 14. Shunt Trip Installation .. 16. Tools Required (not provided) .. 16. Output cables rating .. 16. Installation .. 16. User Input/Output Contacts .. 20. Network Communication Cable .. 21. Modbus Connection .. 21. Optional Equipment .. 22. Seismic Stability Kit .. 22. Seismic side panel locks .. 22. Floor brackets .. 25. Install front anchoring bracket .. 26. Roof stability brackets .. 27. Shielding Troughs.. 27. Post- Installation Checklist .. 28. Specifications .. 29. Full load heat loss at nominal main .. 30. Recommended Conductor Sizes per Phase .. 30. 480 VAC Standard rated (80%) 100% rated .. 30. ii 150 kVA PDU.

6 Overview Important Safety Information Read the instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it. The following special messages may appear throughout this Manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

7 DANGER. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING. WARNING indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury. CAUTION. CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury. NOTICE. NOTICE addresses practices not related to physical injury including certain environmental hazards, potential equipment damage or loss of data. 150 kVA PDU 1. Additional Safety Information Before you begin Verify that the system is free from all short circuits and grounds, except those grounds installed according to local regulations (according to the National electrical Code in the , for instance).

8 If high-potential voltage testing is necessary, follow recommendations in equipment documentation to prevent accidental equipment damage. Before energizing equipment: Remove tools, meters, and debris from equipment. Close the equipment enclosure doors. Remove ground from incoming power lines. Perform all start-up tests recommended by the manufacturer. Operation and Adjustments The following precautions are from the NEMA Standards Publication ICS (English version prevails): Regardless of the care exercised in the design and manufacture of equipment or in the selection and ratings of components, there are hazards that can be encountered if such equipment is improperly operated. It is sometimes possible to misadjust the equipment and thus produce unsatisfactory or unsafe operation.

9 Always use the manufacturer's instructions as a guide for functional adjustments. Personnel who have access to these adjustments should be familiar with the equipment manufacturer's instructions and the machinery used with the electrical equipment. Only those operational adjustments actually required by the operator should be accessible to the operator. Access to other controls should be restricted to prevent unauthorized changes in operating characteristics. WARNING. UNGUARDED MACHINERY HAZARD. Do not use this product with equipment which does not have point-of-operation protection. Do not reach into equipment during operation. Failure to follow these instructions can result in death, serious injury, or equipment damage.

10 2 150 kVA PDU. About This Manual This Manual is intended for users of the specified Schneider Electric equipment. It contains important safety warnings and instructions, gives an introduction to the display interface and provides detailed information for proper use of the equipment. Related Documents Download technical publications and other technical information or look for updates to your Manual at Product Related Information DANGER. HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. Turn off all power supplying this equipment before working on the equipment. Failure to follow these instructions will result in death or serious injury. User Comments Contact We welcome your comments about this document. 150 kVA PDU 3. Component Identification exterior components.


Related search queries