Example: bachelor of science
IronRidge Flush Mount Manual
A. CONNeCT SPLICeS Use Classic Splice or BOSS(Bonded Structural Splice), as needed, to join multiple sections of Rail. Classic Splice Insert Classic Splice 6" into first Rail and secure with two self-drilling screws, spacing them approximately 1” apart and tightening to 20 in-lbs. Slide second Rail over Classic
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Engineering Down to the Deck - IronRidge
files.ironridge.comBuilt-in Waterproofing Sealed from above with a “blind hole” and pre-installed sealing washer, Flat Roof Attachment delivers integrated waterproofing with popular roofing systems, including single-ply and asphaltic. DECK BASE
IronRidge Ground Mount Installation Manual
files.ironridge.comAll electrical installation and procedures should be conducted by a licensed and bonded electrician or solar contractor. Routine maintenance of a module or panel shall not involve breaking or disturbing the bonding path of the system. All work must comply with national, state and local installation procedures, product and safety standards.
XR Rail Family - IronRidge
files.ironridge.comAnodizing prevents surface and structural corrosion, while also providing a more attractive appearance. XR Rail Family The XR Rail Family offers the strength of a curved rail in three targeted sizes. Each size supports specific design loads, while minimizing material costs. Depending on your location, there is an XR Rail to match.
Ground Mount System - IronRidge
files.ironridge.comThe IronRidge Ground Mount System combines our XR100 or XR1000 rails with locally-sourced steel pipes or mechanical tubing, to create a cost-effective structure capable of handling any site or terrain challenge. Installation is simple with only a few structural components and no drilling, welding, or heavy machinery required.
Product Catalog
files.ironridge.comParts Catalog Overview Overview The IronRidge® Flush Mount System is a rail based system for mounting solar modules on pitched roofs. The system utilizes IronRidge XR Rails with a variety of roof attachments to support extreme wind and snow loads. The entire system uses only aluminum and stainless steel components to ensure complete corrosion ...
Related documents
110 RC Requirements for Electrical Installations
www.mikeholt.comUnderground Splices: Single Conductors. Single direct burial conductors of types UF or USE can be spliced underground without a junction box, but the conduc-tors must be spliced with a device listed for direct burial [300.5(E) and 300.15(G)]. Figure 110–12 Multiconductor Cable. Multiconductor UF or USE cable can have the
WIRING DIAGRAMS - 73-87ChevyTrucks.com
www.73-87chevytrucks.commore practical to use a single wire protected by a braided tubing called a loom. Wiring harnesses are joined by using a multiple plug and receptacle connector block, or a terminal post chassis junction block. In the instrument panel area plastic insulated blade-type connectors and screw-type terminals are used.
NEC 2017 Code Changes Chapter 3 - Wiring Methods and …
allstarce.comor cable sheath, shall be left at each outlet, junction, and switch point for splices or the connection of luminaires or devices. Where the opening to an outlet, junction, or switch point is less than 200 mm (8 in.) in any dimension, each conductor shall be long enough to extend at least 75 mm (3 in.) outside the opening.
Pin and Socket Connectors - Farnell
www.farnell.com5001 Pin and Socket Connectors Pin and Socket Connectors Catalog 1308940 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Pin and Socket Connectors - Farnell
www.farnell.com5001 Pin and Socket Connectors Pin and Socket Connectors Catalog 1308940 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514