IVN-8561 Specifications - National Instruments

1 SPECIFICATIONSIVN-8561100 BASE-T1 Media ConverterDefinitionsWarranted Specifications describe the performance of a model under stated operatingconditions and are covered by the model following characteristic Specifications describe values that are relevant to the use of themodel under stated operating conditions but are not covered by the model warranty. Typical Specifications describe the performance met by a majority of models. Nominal Specifications describe an attribute that is based on design, conformance testing,or supplemental are Typical unless otherwise are typical at 25 C unless otherwise CharacteristicsNetwork interfacePorts 1 & 3100 BASE-T1 Ports 2 & 4100 BASE-TXCommunication rate100 MbpsPower RequirementsInput voltage range5 VDC nominal; USB Type CMax power WPhysical CharacteristicsDimensions143 mm 95 mm 38 mm ( in.)

2 In. in.)Weight391 g ( oz)I/O connectorsPorts 1 & 32-position terminal block; AutomotiveEthernetPorts 2 EthernetPowerUSB Type CFront-panel LEDsPowerGreenPorts 1 & 3 Link/Activity, GreenPorts 2 & 4 Link/Activity, Green100 MbpsGreenDIP switchesPorts 1 & 3 Master/SlaveMeasurement Category11 Caution Do not use the IVN-8561 for connections to signals or for measurementswithin Categories II, III, or The protection provided by the IVN-8561 can be impaired if it is used ina manner not described in this Clean the hardware with a soft, nonmetallic brush. Make sure that thehardware is completely dry and free from contaminants before returning it Categories CAT I and CAT O are equivalent. These test and measurement circuits arenot intended for direct connections to the MAINS building installations of Measurement CategoriesCAT II, CAT III, CAT | | IVN-8561 SpecificationsEnvironmentalOperating EnvironmentAmbient temperature range-20 C to 55 C (Tested in accordance withIEC 60068-2-1 and IEC 60068-2-2.

3 Relative humidity range10% to 90%, noncondensing (Tested inaccordance with IEC 60068-2-56.)Maximum Altitude2,000 m (800 mbar)Pollution Degree2 Indoor use EnvironmentAmbient temperature range-20 C to 70 C (Tested in accordance withIEC 60068-2-1 and IEC 60068-2-2.)Relative humidity range5% to 95%, noncondensing (Tested inaccordance with IEC 60068-2-56.)SafetyThis product is designed to meet the requirements of the following electrical equipment safetystandards for measurement, control, and laboratory use: IEC 61010-1, EN 61010-1 UL 61010-1, CSA No. 61010-1 Note For UL and other safety certifications, refer to the product label or the OnlineProduct Certification CompatibilityThis product meets the requirements of the following EMC standards for electrical equipmentfor measurement, control, and laboratory use: EN 61326-1 (IEC 61326-1): Class A emissions.

4 Industrial immunity EN 55011 (CISPR 11): Group 1, Class A emissions EN 55022 (CISPR 22): Class A emissions EN 55024 (CISPR 24): Immunity AS/NZS CISPR 11: Group 1, Class A emissions AS/NZS CISPR 22: Class A emissionsIVN-8561 Specifications | National Instruments | 3 FCC 47 CFR Part 15B: Class A emissions ICES-001: Class A emissionsNote In the United States (per FCC 47 CFR), Class A equipment is intended foruse in commercial, light-industrial, and heavy-industrial locations. In Europe,Canada, Australia and New Zealand (per CISPR 11) Class A equipment is intendedfor use only in heavy-industrial Group 1 equipment (per CISPR 11) is any industrial, scientific, or medicalequipment that does not intentionally generate radio frequency energy for thetreatment of material or inspection/analysis For EMC declarations and certifications, and additional information, refer tothe Online Product Certification Compliance This product meets the essential requirements of applicable European Directives, as follows: 2014/35/EU; Low-Voltage Directive (safety) 2014/30/EU.

5 Electromagnetic Compatibility Directive (EMC)Online Product CertificationRefer to the product Declaration of Conformity (DoC) for additional regulatory complianceinformation. To obtain product certifications and the DoC for this product, visit , search by model number or product line, and click the appropriate link in theCertification ManagementNI is committed to designing and manufacturing products in an environmentally responsiblemanner. NI recognizes that eliminating certain hazardous substances from our products isbeneficial to the environment and to NI additional environmental information, refer to the Minimize Our Environmental Impactweb page at This page contains the environmental regulations anddirectives with which NI complies, as well as other environmental information not included inthis Electrical and Electronic Equipment (WEEE)EU Customers At the end of the product life cycle, all NI products must bedisposed of according to local laws and regulations.

6 For more information abouthow to recycle NI products in your region, visit | | IVN-8561 Specifications RoHS National Instruments (RoHS) National Instruments RoHS (For information about China RoHScompliance, go to )Worldwide Support and ServicesThe NI website is your complete resource for technical support. At , you haveaccess to everything from troubleshooting and application development self-help resources toemail and phone assistance from NI Application for information about the services NI to register your NI product. Product registration facilitates technicalsupport and ensures that you receive important information updates from Declaration of Conformity (DoC) is our claim of compliance with the Council of theEuropean Communities using the manufacturer s declaration of conformity.

7 This systemaffords the user protection for electromagnetic compatibility (EMC) and product safety. Youcan obtain the DoC for your product by visiting If your product supportscalibration, you can obtain the calibration certificate for your product at corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,78759-3504. NI also has offices located around the world. For support in the United States,create your service request at or dial 1 866 ASK MYNI (275 6964). Forsupport outside the United States, visit the Worldwide Offices section of toaccess the branch office websites, which provide up-to-date contact Specifications | National Instruments | 5 Information is subject to change without notice.

8 Refer to the NI Trademarks and Logo Guidelines at forinformation on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of theirrespective companies. For patents covering NI products/technology, refer to the appropriate location: Help Patents in yoursoftware, the file on your media, or the National Instruments Patent Notice at You can findinformation about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Referto the Export Compliance Information at for the NI global trade compliance policy and howto obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES ASTO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS.

9 Customers: The data contained in this manual was developed at private expense and is subject to the applicablelimited rights and restricted data rights as set forth in FAR , DFAR , and DFAR 2017 National Instruments . All rights December 4, 2017