Low Voltage, 0.6 , Dual SPDT Analog Switch - Vishay

1 Siliconix S16-0650-Rev. C, 18-Apr-161 Document Number: 67590 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT voltage , , dual SPDT Analog SwitchDESCRIPTIONThe DG2735A is a low voltage , low on-resistance, dual single-pole/double-throw (SPDT) monolithic CMOS Analog Switch designed for high performance switching ofanalog signals. Combining low-power, high speed, lowon-resistance, and small package size, the DG2735A, isideal for portable and battery powered DG2735A has an operation range from V to Vsingle supply. The DG2735A has two separate control pinsfor independent control of the two SPDT switches. The DG2735A is guaranteed V logic compatible,allowing easy interface with low voltage DSP or MCU controllogic and ideal for one cell Li-ion battery direct Switch conducts signals within the power rails equallywell in both directions when on, and blocks up to the powersupply level when off.

2 Break-before-make is DG2735A is built on Vishay Siliconix's sub micronCMOS low voltage process technology and providesgreater than 400 mA latch-up protection, as tested a committed partner to the community and theenvironment, Vishay Siliconix manufactures this productwith lead (Pb)-free device terminations. DG2735A isoffered in a miniQFN package. The miniQFN packagehas a nickel-palladium-gold device termination and isrepresented by the lead (Pb)-free -GE4 suffix. Thenickel-palladium-gold device terminations meet all JEDEC standards for reflow and MSL low voltage operation ( V to V) Low on-resistance - RON: at V Fast switching: tON = 55 ns at V TOFF = 15 ns at V Latch-up current > 400 mA (JESD78) Material categorization: for definitions of complianceplease see BENEFITS Reduced power consumption High accuracy Reduce board space V logic compatibleAPPLICATIONS Cellular phones Speaker headset switching Audio and video signal routing PCMCIA cards Battery operated systems Portable media players Handheld test instrumentsFUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATIONTRUTH TABLELOGICNC1, 2NO1, 20 ONOFF1 OFFONGNDNC2DG2735 AminiQFN-10L6721V+NO1 COM1NC1IN1345IN2 COM2NO28910 Pin 1: LONG LEADD evice Marking: Hx for DG2735Ax = Date/Lot Traceability Code(Top View)Pin 1 Note: Pin 1 has long Siliconix S16-0650-Rev.

3 C, 18-Apr-162 Document Number: 67590 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Signals on NC, NO, or COM or IN exceeding V+ will be clamped by internal diodes. Limit forward diode current to maximum current All leads welded or soldered to PC Derate 4 mW/C above 70 INFORMATIONPART NUMBERCONFIGURATION Switch FUNCTIONTEMP. RANGEPACKAGEREEL QUANTITYDG2735 ADN-T1-GE4 dual DPSTNC / NO-40 C to +85 CminiQFN10, mm x mm3000 ABSOLUTE MAXIMUM RATINGS (TA = 25 C, unless otherwise noted)PARAMETER SYMBOL LIMITUNIT Reference to GNDV+ V to +6 VVIN, COM, NC, NO V to (V+ + )Current (Any terminal except NO, NC or COM)30mAContinuous Current (NO, NC, or COM) 300 Peak Current (Pulsed at 1 ms, 10 % duty cycle) 500 Storage Temperature (D Suffix)-65 to +150 CPower Dissipation (Packages) bminiQFN10 c208mWLatch Up CurrentJESD78A>400mAESD - HBMANSI / ESDA / JEDEC JS-001>5000 VESD - CDM JESD22-C101>1000 ESD - MMJESD22-A115>200 SPECIFICATIONS (V+ = 3 V)

4 PARAMETER SYMBOL TEST CONDITIONS UNLESS OTHERWISE SPECIFIEDV+ = 3 V, 10 %,VIN = V or V eTEMP. a LIMITS -40 C to +85 CUNIT MIN. b TYP. cMAX. bAnalog SwitchAnalog Signal Range dVanalogRDS(on)Full0-V+VOn-ResistanceRDS (on)V+ = V, INO/NC = 100 mA, VCOM = V+ = V, INO/NC = 100 mA, VCOM = VV+ = V, INO/NC = 100 mA, VCOM = + = V, INO/NC = 100 mA, VCOM = VV+ = V, INO/NC = 100 mA, VCOM = + = V, INO/NC = 100 mA, VCOM = + = V, INO/NC = 100 mA, VCOM = + = V, INO/NC = 100 mA, VCOM = VRON Match d RONV+ = V, INO/NC = 100 mA, VCOM = V, + = V, INO/NC = 100 mA, VCOM = V, VRON resistance flatness dRON flatnessV+ = V, INO/NC = 100 mA, VCOM = V, Off Leakage CurrentINO/NC(off)V+ = 5 V, VNO/NC = V,VCOM = VRoom-8-8nAFull-50-50 ICOM(off)Room-8-8 Full-50-50 Channel-On Leakage CurrentICOM(on)V+ = 5 V, VNO/NC = VCOM = Siliconix S16-0650-Rev.

5 C, 18-Apr-163 Document Number: 67590 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Room = 25 C, Full = as determined by the operating The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data Typical values are for design aid only, not guaranteed nor subject to production Guarantee by design, not subjected to production VIN = input voltage to perform proper beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operationof the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximumrating conditions for extended periods may affect device ControlInput High Low CapacitanceCINFull-6-pFInput CurrentIINL or IINHVIN = 0 or V+Full-1-1 ADynamic CharacteristicsBreak-Before-Make Time etBBMV+ = V, VNO, VNC = V, RL = 50 , CL = 35 pFRoom115-nsTurn-On Time etONRoom-2878 Full--80 Turn-Off Time etOFFRoom-1358 Full--60 Off-Isolation dOIRRRL = 50 , CL = 5 pF, f = 100 kHzRoom--70-dBCrosstalk dXTALK--90-3dB bandwidth dRL = 50 , CL = 5 pFRoom-120-MHzNO, NC Off Capacitance dCNO(off)VIN = 0 V, or V+, f = 1 MHzRoom-40-pFCNC(off)-40-Channel On Capacitance dCNO(on)-120-CNC(on)-120-Power SupplyPower Supply RangeV+ Supply CurrentI+VIN = 0 or V+Full--1 ASPECIFICATIONS (V+ = 3 V)PARAMETER SYMBOL TEST CONDITIONS UNLESS OTHERWISE SPECIFIEDV+ = 3 V, 10 %,VIN = V or V eTEMP.

6 A LIMITS -40 C to +85 CUNIT MIN. b TYP. cMAX. Siliconix S16-0650-Rev. C, 18-Apr-164 Document Number: 67590 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT CHARACTERISTICS (TA = 25 C, unless otherwise noted)RON vs. VCOM and Supply VoltageRON vs. Analog voltage and TemperatureRON vs. Analog voltage and TemperatureSupply Current vs. ( )VCOM- Analog voltage (V)V+ = + VV+ = + VV+ = + VV+ = + VV+ = + VV+ = + VV+ = + VV+ = + VTA= +25 CINO/NC = ( )VCOM- Analog voltage (V)V+ = + VIS= 100 mA NC/NO+ 85 C+ 25 C-40 ( )VCOM- Analog voltage (V)V+ = + VIS= 100 mA NC/NO+ 85 C+ 25 C-40 C012345-40-200 20406080100I+ -Supply Current (nA)Temperature ( C)V+ = + = GNDV+ = +3 VIN = V+V+ = +3 VIN = GNDV+ = + = V+ Siliconix S16-0650-Rev.

7 C, 18-Apr-165 Document Number: 67590 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT CHARACTERISTICS (TA = 25 C, unless otherwise noted)Leakage Current vs. TemperatureSupply Current vs. Switching Frequency Switching Threshold vs. Supply VoltageSwitching Time vs. TemperatureInsertion Loss, Off-Isolation Crosstalk vs. FrequencySupply Current vs. VIN100100010 000100 000-40-200 20406080100 Leakage Current (pA)Temperature ( C)ICOM(ON)INC(OFF)ICOM(OFF)V+= + 5 000I+ -Supply Current ( A)Input Switching Frequency (Hz)100K10K1000100101M10MV+ = + +25 Threshold (V)V+ -Supply voltage (V)VIH= -40 CVIL= 85 C-40 C to +85 C0510152025303540-40-200 20406080100tON, tOFF-Switching Time (ns)Temperature ( C)V+ = + VtON(NC)tON(NO)tOFF(NO)tOFF(NC)- 110- 100- 90- 80- 70- 60- 50- 40- 30- 20- 10010 Loss, OIRR, XTALK(dB)Frequency (Hz)1M10M100M1 GLossXTALKOIRRV+ = +3 VRL= 50 100K10p100p1n10n100n1 10 100 + -Supply Current (A)VIN(V)T = 25 CV+ = + = + = + = Siliconix S16-0650-Rev.

8 C, 18-Apr-166 Document Number: 67590 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT CIRCUITS Fig. 1 - Switching Time Fig. 2 - Break-Before-Make IntervalSwitchInputCL (includes fixture and stray capacitance)V+INNO or NCCL35 pFCOML ogicInputRL50 VOUTGNDV+50%0 VLogicInputSwitchOutputtONtOFFL ogic 1 = Switch OnLogic input waveforms inverted for switches that havethe opposite logic VSwitch x VOUTtr 5 nstf 5 nsVINHVINL =+<<()CL (includes fixture and stray capacitance)NCVNONOVNC0 VLogicInputSwitchOutputVOVNC = VNOtr < 5 nstf < 5 ns90%tDtDINCOMV+GNDV+CL35 pFVORL50 Siliconix S16-0650-Rev. C, 18-Apr-167 Document Number: 67590 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT CIRCUITS Fig.

9 3 - Charge Injection Fig. 4 - Off-Isolation Fig. 5 - Channel Off/On CapacitanceVishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for SiliconTechnology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, andreliability data, see = VOUT x CLCL = 1 nFRgenVOUTCOMVIN = 0 - V+INGNDV+V+IN depends on Switch configuration: input polaritydetermined by sense of Switch .+NC or NOVgen INGNDNC or NO0V, V10 nFCOMOff Isolation20 logVCOMVNO /NCRLA nalyzerV+V+COM=NC or NOf = 1 MHzINCOMGND0 V, VMeterHP4192 AImpedanceAnalyzeror Equivalent10 nFV+V+Package Siliconix Revision: 16-May-161 Document Number: 74496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT QFN-10L CASE OUTLINENote(1)The dimension depends on the leadframe that assembly house - or REF (1) or REF (1) ECN T16-0163-Rev.

10 B, 16-May-16 DWG: 5957 Document Number: : 05-Mar-101 PAD PatternVishay Siliconix RECOMMENDED MINIMUM PADS FOR MINI QFN 10 LMounting FootprintDimensions in mm (inch)10 ( )19 ( ) ( ) ( ) ( ) ( ) ( )Legal Disclaimer Revision: 08-Feb-171 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability.