m Series Pressure regulators - Emerson

1 instruction manual D103658X012 Type M. January 2015 - Rev. 00. M Series Pressure regulators Summary Introduction .. 1. Categories and Fluid Group .. 2. Characteristics .. 2. Labelling .. 2. Overpressure Protection .. 3. Transport and Handling .. 3. Atex Requirements .. 3. Slam-Shut Controller .. 3. Dimensions and Weights .. 4. Operation .. 5. Installation .. 6. Startup .. 7. Adjustment .. 8 Figure 1. Regulator Type MBN. Shutdown .. 8. Periodical Checks .. 8 This product has been designed to be used with fuel gases of Maintenance.

2 8 1st and 2nd family according to EN 437, and with other non aggressive and non fuel gases. For any other gases, other Spare Parts .. 9 than natural gas, please contact your local sales agent. Troubleshooting .. 10 The following versions are available: Parts List .. 10. MN MF: Regulator ( Pressure accessories). Schematic Assemblies .. 11. MBN MBF: Regulator with slam-shut (safety accessories). MBN-M MBF-M: Monitor with slam-shut (safety accessories). INTRODUCTION MN, MF, MBN and MBF Series with SR silencer are also available.

3 Scope of manual The standard gas Pressure devices ( regulators and safety shut-off devices) are those used in the assemblies dealt with This manual provides instructions for installation, startup, into EN 12186 and EN 12279 and their use has to be under maintenance and spare parts ordering for the M Series the provisions into ENs 12186 & 12279. spring loaded regulators . In the Pressure regulators manufactured by Emerson Process Management shall be used additional Pressure Product Description accessories ( slam-shut controller) manufactured and labeled by Emerson Process Management.

4 The M Series regulators are fail open, differential strength, spring loaded whit counterbalanced shutter. They can be provided with Emerson Process Management will be not responsible slam-shut controller for minimum Pressure , maximum Pressure for any possible inefficiency due to installation of not own or minimum and maximum downstream Pressure . production additional Pressure accessories ( slam-shut controller). The regulators of the M Series due to their operating specifications are mainly used in those system where When Pressure containing parts of possible built-in safety sudden capacity variations are required, or else, where the shut-off device (SSD) valve and pilot have different cut-off of the gas distribution is controlled by solenoid valve, maximum allowable pressures, the SSD is differential such as for the feeding of burners.

5 Strength type. TM. Type M. CATEGORIES AND FLUID GROUP MF MBF MBF-M DN 80-100: 5 bar **. MN-PST MBN-PST MBN-M-PST: bar *. Fail open stand-alone M Series regulators cannot be used as a safety accessory according PED 97/23/EC to protect MF-PST MBF-PST MBF-M-PST: bar *. downstream Pressure equipment. MN-AP MBN-AP MBN-M-AP: bar *. According to EN 14382, only in integral strength type and MF-AP MBF-AP MBF-M-AP: bar *. Class A configuration (when both over and under Pressure MN-APA MBN-APA MBN-M-APA: bar *. protections are set up), the possible built-in safety shut-off MF-APA MBF-APA MBF-M-APA: bar *.

6 Device can be classified like a safety accessory according to PED. * At average ambient temperature. The minimum PS between SSD valve and slam-shut ** PST version is available on request to allow a Maximum controller shall be the PS of the safety accessory to comply Operating Inlet Pressure = bar at average ambient the provisions of EN 14382 about integral strength type. temperature. Downstream equipments, protected by possible built-in safety shut-off device (in its Class A and integral strength Outlet Set Pressure Ranges configuration) of this product, shall have technical features MN MF: 10 to 500 mbar *.

7 Such as to be category per table below according Directive MN-PST MF-PST: to bar 97/23/EC PED . MN-AP MF-AP: to 1 bar Table 1. M Series regulators Category MN-APA MF-APA: 1 to 3 bar Product Size category fluid group * For DN 80 and 100 the operating outlet set Pressure range to bar is allowable with BP version. DN 25 sep DN 40 TO DN 50 i Minimum/Maximum Allowable Temperature (TS). DN 65 to DN 100 ii 1 See label. all sizes with IV. slam-shut Functional Features Accuracy class AC : up to 5% . The regulator size DN 25 and possible built-in Pressure Lock-up Pressure class SG : up to +10%.

8 Accessories ( slam-shut controller OS/66) installed in all the available sizes of M Series regulators , are conform Class of lock-up Pressure zone SZ : up to 10%. to Pressure Equipment Directive (PED) 97/23/EC Article 3 section 3 and were designed and manufactured in Slam-Shut Controller accordance with sound engineering practice (SEP). Accuracy class AG : 5%. Per Article 3 section 3, these SEP products must not bear Response time ta : 1 s the CE marking. Temperature Standard version: Working -10 +60 C. Characteristics Low temperature version: Working -20 +60 C.

9 Body Sizes and End Connection Styles Materials MN MBN MBN-M (widened outlet) Flanges and covers: Steel DN 25x65, 40x80, 50x100, 65x100, 80x150, 100x200 Diaphragm: Fabric NBR+PVC/Nitrile rubber PN 16, ANSI 150 Pads: Nitrile (NBR) rubber MF MBF MBF-M (Same Size Inlet/Outlet). DN 25, 40, 50, 65, 80, 100 labelling PN 16, ANSI 150. Notified body APPARECCHIO TIPO / DEVICE TYPE. Warning BOLOGNA ITALY. ! TARTARINI xxxx Note 1. MATRICOLA / ANNO. SERIAL Nr. / YEAR / Note 2 DN1. The Pressure /temperature limits indicated in REAZIONE FAIL OPEN X FAIL CLOSE DN2.

10 FAIL SAFE MODE. this instruction manual or any applicable stan- NORME ARMONIZ. EN Wds bar HARMONIZED STD. dard or code limitation should not be exceeded. CLASSE DI PERDITA TIPO. LEAKAGE CLASS TYPE Wdso bar CLASSE FUNZIONALE. Maximum Operating Inlet Pressure FUNCTIONAL CLASS Cg Wdsu bar FLUIDO GRUPPO DN seat MN MBN MBN-M DN 25-40-50: 10 bar ** FLUID GROUP 1 pmax bar DN sede pdo bar TS Note 3 C PS Note 4 bar PSD Note 5 Bar PT= x PS bar MN MBN MBN-M DN 65-80-100: 5 bar **. MF MBF MBF-M DN 25-40-50: 10 bar ** Figure 2.