OPERATING GUIDE GPIB DC POWER SUPPLIES …

1 OPERATING GUIDEGPIB DC POWER SUPPLIESA gilent technologies Models 664xa , 665xA, 667xA, and 668xAAGILENT model 6641A: 3217A-00111 and Above * agilent model 6642A: 3204A-00111 and Above * agilent model 6643A: 3205A-00111 and Above * agilent model 6644A: 3213A-00111 and Above * agilent model 6645A: 3215A-00111 and Above * agilent model 6651A: 3130A-00171 and Above * agilent model 6652A: 3201A-00381 and Above * agilent model 6653A: 3145A-00551 and Above * agilent model 6654A: 3148A-00391 and Above * agilent model 6655A: 3152A-00176 and Above * agilent model 6671A: 3129A-00218 and Above * agilent model 6672A: 3138A-00101 and Above * agilent model 6673A: 3138A-00101 and Above * agilent model 6674A: 3133A-00161 and Above * agilent model 6675A: 3138A-00101 and Above * agilent model 6680A: 3302A-00101 and Above * agilent model 6681A: 3250A-00101 and Above * agilent model 6682A: 3339A-00101 and Above * agilent model 6683A: 3339A-00161 and Above * agilent model 6684A: 3339A-00101 and Above ** For instruments with higher Serial Numbers, a change page may be included.

2 S1 agilent Part No. 5961-2579 Printed in USA: March 1995 Microfiche Part No. 5961-2580 Reprinted: April 20002 CERTIFICATIONA gilent technologies certifies that this product met its published specifications at time of shipment from the technologies further certifies that its calibration measurements are traceable to the United States NationalBureau of Standards, to the extent allowed by the Bureau s calibration facility, and to the calibration facilities of otherInternational Standards Organization agilent technologies hardware product is warranted against defects in material and workmanship for a period of threeyears from date of delivery.

3 agilent technologies software and firmware products, which are designated by AgilentTechnologies for use with a hardware product and when properly installed on that hardware product, are warranted not tofail to execute their programming instructions due to defects in material and workmanship for a period of 90 days from dateof delivery. During the warranty period agilent technologies will, at its option, either repair or replace products whichprove to be defective. agilent technologies does not warrant that the operation of the software, firmware, or hardware shallbe uninterrupted or error warranty service, with the exception of warranty options, this product must be returned to a service facility designatedby agilent technologies .

4 Customer shall prepay shipping charges by (and shall pay all duty and taxes) for products returnedto agilent technologies for warranty service. Except for products returned to Customer from another country, AgilentTechnologies shall pay for return of products to services outside the country of initial purchase are included in agilent technologies product price, only ifCustomer pays agilent technologies international prices (defined as destination local currency price, or or GenevaExport price).If agilent technologies is unable, within a reasonable time to repair or replace any product to condition as warranted, theCustomer shall be entitled to a refund of the purchase price upon return of the product to agilent OF WARRANTYThe foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the Customer,Customer-supplied software or interfacing, unauthorized modification or misuse, operation outside of the environmentalspecifications for the product, or improper site preparation and maintenance.

5 NO OTHER WARRANTY IS EXPRESSEDOR IMPLIED. agilent technologies SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULAR REMEDIESTHE REMEDIES PROVIDED HEREIN ARE THE CUSTOMER S SOLE AND EXCLUSIVE REMEDIES. AGILENTTECHNOLOGIES SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, ORCONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL above statements apply only to the standard product warranty. Warranty options, extended support contracts, productmaintenance agreements and customer assistance agreements are also available. Contact your nearest AgilentTechnologies Sales and Service offices for further information on agilent technologies full line of Support SUMMARYThe following general safety precautions must be observed during all phases of operation, service, and repair of thisinstrument.

6 Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safetystandards of design, manufacture, and intended use of the instrument. agilent technologies assumes no liability for thecustomer s failure to comply with these APPLYING that the product is set to match the available line voltage and the correct fuse is THE product is a Safety Class 1 instrument (provided with a protective earth terminal). To minimize shock hazard, the instrument chassisand cabinet must be connected to an electrical ground. The instrument must be connected to the ac POWER supply mains through a three-conductor POWER cable, with the third wire firmly connected to an electrical ground (safety ground) at the POWER outlet.

7 For instrumentsdesigned to be hard-wired to the ac POWER lines (supply mains), connect the protective earth terminal to a protective conductor before anyother connection is made. Any interruption of the protective (grounding) conductor or disconnection of the protective earth terminal willcause a potential shock hazard that could result in personal injury. If the instrument is to be energized via an external autotransformer forvoltage reduction, be certain that the autotransformer common terminal is connected to the neutral (earthed pole) of the ac POWER lines(supply mains). fuses with the required rated current, voltage, and specified type (normal blow, time delay, etc.)

8 Should be used. Do not use repairedfuses or short circuited fuseholders. To do so could cause a shock or fire NOT OPERATE IN AN EXPLOSIVE not operate the instrument in the presence of flammable gases or AWAY FROM LIVE personnel must not remove instrument covers. Component replacement and internal adjustments must be made by qualifiedservice personnel. Do not replace components with POWER cable connected. Under certain conditions, dangerous voltages may exist evenwith the POWER cable removed. To avoid injuries, always disconnect POWER , discharge circuits and remove external voltage sources beforetouching NOT SERVICE OR ADJUST not attempt internal service or adjustment unless another person, capable of rendering first aid and resuscitation, is NOT EXCEED INPUT instrument may be equipped with a line filter to reduce electromagnetic interference and must be connected to a properly groundedreceptacle to minimize electric shock hazard.

9 Operation at line voltages or frequencies in excess of those stated on the data plate maycause leakage currents in excess of mA manual symbol: the product will be marked with this symbol when it is necessary for the user to refer to theinstruction manual (refer to Table of Contents) .Indicates hazardous earth (ground) WARNING sign denotes a hazard. It calls attention to a procedure, practice, or the like, which, if not correctlyperformed or adhered to, could result in personal injury. Do not proceed beyond a WARNING sign until theindicated conditions are fully understood and CAUTION sign denotes a hazard. It calls attention to an OPERATING procedure, or the like, which, if not correctlyperformed or adhered to, could result in damage to or destruction of part or all of the product.

10 Do not proceedbeyond a CAUTION sign until the indicated conditions are fully understood and NOT SUBSTITUTE PARTS OR MODIFY of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modification to theinstrument. Return the instrument to an agilent technologies Sales and Service Offices for service and repair to ensure that safetyfeatures are which appear damaged or defective should be made inoperative and secured against unintended operation until they can berepaired by qualified service SUMMARY (continued)GENERALAny LEDs used in this product are Class 1 LEDs as per IEC CONDITIONSWith the exceptions noted, all instruments are intended for indoor use in an installation category II, pollution degree 2environment.