Optocoupler, Phototransistor Output, Dual Channel, SOIC …

1 ILD205T, ILD206T, ILD207T, ILD211T, Semiconductors Rev. , 23-Oct-151 Document Number: 83647 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT , Phototransistor output , dual Channel, SOIC-8 PackageDESCRIPTIONThe ILD205T, ILD206T, ILD207T, ILD211T, and ILD213T are optically coupled pairs with a gallium arsenide infrared LED and a silicon NPN Phototransistor . Signal information, including a DC level, can be transmitted by the device while maintaining a high degree of electrical isolation between input and output . The ILD205T, ILD206T, ILD207T, ILD211T, and ILD213T come in a standard SOIC-8 small outline package for surface mounting which makes it ideally suited for high density applications with limited space. In addition to eliminating through-holes requirements, this package conforms to standards for surface mounted specified minimum and maximum CTR allows a narrow tolerance in the electrical design of the adjacent circuits.

2 The high BVCEO of 70 V gives a higher safety margin compared to the industry standard of 30 Two channel coupler SOIC-8 surface mountable package Standard lead spacing of " Available only on tape and reel option (conforms to EIA standard 481-2) Isolation test voltage, 4000 VRMS Compatible with dual wave, vapor phase and IR reflow soldering Material categorization: for definitions of compliance please see APPROVALS UL1577, file no. E52744 system code Y cUL - file no. E52744, equivalent to CSA bulletin 5A i179018-2A1C2A3C48C7E6C5Ei179025 ORDERING INFORMATIONILD2##TPART NUMBERAGENCY CERTIFIED/PACKAGECTR (%)10 mAUL, cUL40 to 8063 to 125100 to 200 20 mmILD205T, ILD206T, ILD207T, ILD211T, Semiconductors Rev. , 23-Oct-152 Document Number: 83647 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

3 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability.(1)Refer to reflow profile for soldering conditions for surface mounted Minimum and maximum values were tested requierements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST CONDITIONSYMBOLVALUEUNITINPUTPeak reverse voltageVR6 VPeak pulsed current1 s, 300 pps1 AContinuous forward current per channelIF30mAPower dissipationPdiss50mWOUTPUTC ollector emitter breakdown voltageBVCEO70 VEmitter collector breakdown voltageBVECO7 VPower dissipation per channel Pdiss125mWCOUPLERT otal package dissipation ambient (2 LEDs and 2 detectors, 2 channels)Ptot350mWStorage temperatureTstg-55 to +150 COperating temperatureTamb-55 to +100 CSoldering time from 260 C (1)Tsld10sELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)

4 PARAMETERTEST voltageIF = 10 currentVR = 6 ACapacitanceVR = 0 VCO-25-pFOUTPUTC ollector emitter breakdown voltageIC = 10 ABVCEO70--VEmitter collector breakdown voltageIE = 10 ABVECO7- -VCollector emitter leakage currentVCE = 10 V, IF = 0 AICEO-550nACollector emitter capacitanceVCE = 0 VCCE-10-pFCOUPLERC ollector emitter saturation voltageIF = 10 mA, IC = (input to output ) pFCURRENT TRANSFER RATIO (Tamb = 25 C, unless otherwise specified)PARAMETERTEST = 5 V, IF = 10 mAILD205 TCTRDC40-80%ILD206 TCTRDC63-125%ILD207 TCTRDC100-200%ILD211 TCTRDC20--%ILD213 TCTRDC100--%VCE = 5 V, IF = 1 mAILD205 TCTRDC1330-%ILD206 TCTRDC2245-%ILD207 TCTRDC3470-%ILD205T, ILD206T, ILD207T, ILD211T, Semiconductors Rev. , 23-Oct-153 Document Number: 83647 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 1 - Test Circuit, Non-Saturated OperationFig.

5 2 - Test Circuit, Saturated OperationFig. 3 - Switching TimesSWITCHING CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST timeVS = 5 V, IC = 2 mA, RL = 100 ,(see figure 1)td-3- sRise timeVS = 5 V, IC = 2 mA, RL = 100 ,(see figure 1)tr-3- sFall timeVS = 5 V, IC = 2 mA, RL = 100 ,(see figure 1) sStorage timeVS = 5 V, IC = 2 mA, RL = 100 ,(see figure 1) sTurn-on timeVS = 5 V, IC = 2 mA, RL = 100 ,(see figure 1)ton-6- sTurn-off timeVS = 5 V, IC = 2 mA, RL = 100 ,(see figure 1)toff-5- sTurn-on timeVS = 5 V, IF = 10 mA, RL = 1 k ,(see figure 2)ton-3- sTurn-off timeVS = 5 V, IF = 10 mA, RL = 1 k ,(see figure 2)toff-10- sChannel I channel II95 10804RG = 50 tptp = 50 s T= + 5 V IF050 100 IFIC = 2 mA; adjusted throughinput amplitudeOscilloscopeRL= 1 M CL= 20 pFChannel IChannel II95 10843RG= 50 tptp= 50 sT= + 5 VICIF050 1 k IF= 10 mAOscilloscopeRL CL20 pF 1 M tptt0010 %90 %100 %trtdtontstftoffIFICtpPulse durationtdDelay timetrRise timeton(= td + tr) Turn-on timetsStorage timetfFall timetoff(= ts + tf)Turn-off time96 11698 ILD205T, ILD206T, ILD207T, ILD211T, Semiconductors Rev.

6 , 23-Oct-154 Document Number: 83647 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT As per IEC 60747-5-5, , this optocoupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)Fig. 4 - Forward Voltage vs. Forward CurrentFig. 5 - Collector Current vs. Collector Emitter Voltage (non-saturated)Fig. 6 - Leakage Current vs. Ambient TemperatureFig. 7 - Collector Current vs. Collector Emitter Voltage (saturated)SAFETY AND INSULATION RATINGSPARAMETERTEST CONDITIONSYMBOLVALUEUNITC limatic classificationAccording to IEC 68 part 155/100/21 Comparative tracking index CTI175 Tested withstanding isolation voltageAccording to UL1577, t = 1 sVISO4000 VRMSM aximum transient isolation voltageAccording to DIN EN 60747-5-5 VIOTM6000 VpeakMaximum repetitive peak isolation voltageAccording to DIN EN 60747-5-5 VIORM560 VpeakIsolation resistanceTamb = 25 C, VIO = 500 VRIO 1012 Tamb = 100 C, VIO = 500 VRIO 1011 output safety powerPSO350mWInput safety currentISI150mAInput safety temperatureTS165 CCreepage distanceDIP-6, option 64mmClearance distanceDIP-6, option 64mmInsulation - Forward Voltage (V)IF - Forward Current (mA)Tamb = 0 CTamb = 25 CTamb = 50 CTamb = 75 CTamb = 100 CTamb = -55 C2232705101520250246810IC - Collector Current (mA)

7 VCE - Collector Emitter Voltage (NS) (V)IF = 30 mAIF = 20 mAIF = 15 mAIF = 10 mAIF = 5 - Leakage Current (nA)Tamb - Ambient Temperature ( C)IF = 0 mAVCE = 40 VVCE = 24 VVCE = 12 V-60 -40 -20020406080 - Collector Current (mA)VCE - Collector Emitter Voltage (sat) (V)IF = 25 mAIF = 10 mAIF = 5 mAIF = 2 mAIF = 1 mAILD205T, ILD206T, ILD207T, ILD211T, Semiconductors Rev. , 23-Oct-155 Document Number: 83647 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 8 - Normalized CTR (saturated) vs. Ambient TemperatureFig. 9 - Normalized CTR (non-saturated) vs. Ambient TemperatureFig. 10 - Normalized CTR (non-saturated) vs. Forward CurrentFig. 11 - Normalized CTR (saturated) vs. Forward CurrentFig. 12 - Switching Time vs. Load ResistanceFig.

8 13 - Power Dissipation vs. Ambient -40 -20 020 40 60 80 100 120 NCTR- Normalized CTR (non-sat.)Tamb- Ambient Temperature ( C)Normalized to CTR value:IF= 10 mA, VCE= 5 V, Tamb= 25 CIF= 10 mAIF= 1 -40 -20 020 40 60 80 100 120 NCTR- Normalized CTR (sat.)Tamb- Ambient Temperature ( C)Normalized to CTR value:IF= 10 mA, VCE= 5 V, Tamb= 25 CIF= 10 mAIF= 1 Normalized CTR (NS)IF- Forward Current (mA)Normalized to:IF= 10 mA, VCE = 5 V,Tamb= 25 CTamb= 0 CTamb= 100 CTamb= 75 CTamb= -55 CTamb= 25 Normalized CTR (sat)IF- Forward Current (mA)VCE= VNormalized to:IF= 10 mA,VCE= 5 V,Tamb= 25 CTamb= 0 CTamb= 75 CTamb= -55 CTamb= 25 CTamb= 100 , toff - Switching Time ( s)RL - Load Resistance (k )ton ( s)toff ( s)VCE = 5 V, IF = 10 mA050100150200250300350400-55-30-5204570 95120 Package Power Dissipation (mW)Tamb - Ambient Temperature ( C) dual channelSingle channelILD205T, ILD206T, ILD207T, ILD211T, Semiconductors Rev.

9 , 23-Oct-156 Document Number: 83647 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT DIMENSIONS (in millimeters)PACKAGE MARKING (example)Note Tape and reel suffix (T) is not part of the package YWW Y 68 ILD205T, ILD206T, ILD207T, ILD211T, Semiconductors Rev. , 23-Oct-157 Document Number: 83647 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT AND REEL PACKAGING FOR dual CHANNELS (1) (in millimeters) Selected dual SOIC8 optocouplers are available in tape and reel format. To order surface mount ILD2XX optocoupler on tape and reel, add a suffix T after the part number, , tape is 16 mm and is wound on a 33 cm reel.

10 There are 2000 parts per reel. Taped and reeled dual SOIC8 optocouplers conform to EIA-481-2 and IEC (1)Select dual channel devices are available in the shorter SOIC-8 package and will be taped according to the single channel taping specification Fig. 14 SOLDER PROFILEFig. 15 - Lead (Pb)-free Reflow Solder Profileaccording to J-STD-020 HANDLING AND STORAGE CONDITIONSESD level: HBM class 2 Floor life: unlimitedConditions: Tamb < 30 C, RH < 85 %Moisture sensitivity level 1, according to ( ) ( ) ( ) ( ) ( ) ( )180044 ( )2 ( ) ( ) ( ) ( ) ( ) ( )EmbossmentDirection of feedCenter linesof cavity10 pitch cumulative tolerance on tape ( ) ( ) 1 and top of componentTopcovertape0501001502002503000 50100150200250300 Time (s)Temperature ( C)240 C245 Cmax. 260 Cmax. 120 smax. 100 s217 Cmax. 30 smax.