Transcription of Protecting people and the environment from the …
1 eaton Guardian SleeveProtecting people and the environment from the effects of hose s new Guardian Sleeve is designed to protect against damage or injury which may result from a hydraulic hose failure. The ultra-tight weave disperses pressure and fluids that may escape during a hose burst or pinhole leak. With this new line of sight sleeving, both equipment operators and the environment are guarded from the effects of hose Meets new line of sight operator specification EN982 ISO norm 833 EN414 and ISO 3457 The ultra tight weave resists oil spillage from hose failure Meets ASTM D6770 for abrasion resistance of textile webbing Meets abrasion standard ISO 6945 Meets Fed-STD191-Test Method 5309 for abrasion Densely twisted polyamide 6 yarn offers optimum UV and abrasion protection MSHA approved # IC-234/0 Meets standard applica- tion procedures for accep- tance of Flame Resistance Solid Products taken into mines Meets Conductivity Requirements of ISO 8031 Tight.
2 Smooth surface resists wearChemical Compatibility Gasoline Very GoodOil Very GoodMineral and Vegetable Oil Very GoodIonic Metallic Solutions Very GoodAlcohols Very GoodDiluted Bases Very GoodDiluted acids GoodBenzene Very GoodAcetone Very GoodEther Very GoodCarbon Tetrachloride Very GoodChlorine Based Solvent Very GoodMold, Bacteria, Moths Very Good*Strong and concentrated acids; ie. HCl or Formic Acid may have some corrosive Compatibility Chart for Guardian SleevingEaton Guardian Sleeve 2011 eaton CorporationAll Rights Reserved Printed in USAD ocument No. E-HOOV-TH001-E3 July 2011 eaton Hydraulics Group USA14615 Lone Oak RoadEden Prairie, MN 55344 USATel: 952-937-9800 Fax: Group EuropeRoute de la Longeraie 71110 MorgesSwitzerlandTel: +41 (0) 21 811 4600 Fax: +41 (0) 21 811 4601 eaton Hydraulics Group Asia PacificEaton Building4th Floor, No.
3 3 Lane 280 Linhong Rd. Changning DistrictShanghai 200335 ChinaTel: (+86 21) 5200 0099 Fax: (+86 21) 5200 0400 Properties Specication Description Burst Pressure 16,000 psi Capable to contain hose burst up to 16,000 psi Pin Hole Leak Pressure 4,000 psi Sustained 4,000 psi pin hole deflection from focused 1mm pin hole Abrasion Cycles 250,000 Holds up to 250,000 Abrasion cycles per ISO 6945 Properties and SpecificationsDenier: 1260 Melting Point: 215 C/420 FMaterial: Polyamide 6, made with pre-dyed yarnDim. Stability: Great resistance to sun, atmospheric agents and agingToxicity: Non-ToxicColor: BlackPacking Requirements: eaton Guardian Sleeve comes in a 300 foot roll with no more than 3 cuts per roll and no piece shorter than 30 feet. Note must be ordered by the Nominal A Flat Width Weights in lbs Rolls Number (in) (in) +/- per 300 ft Roll per BoxFF90754-68 8FF90754-79 7FF90754-91 6FF90754-98 6FF90754-106 5FF90754-122 4FF90754-142 4FF90754-157 3FF90754-173 3FF90754-185 3FF90754-209 2FF90754-219 2FF90754-238 2FF90754-288 2FF90754-366 1 Table 1: General and Dimensional InformationAssembly Instructions1.
4 Select the correct sleeve part number for the hose as outlined in the Table Cut the sleeve 2 inches longer than the cut length of the hose to allow full hose bend The ends of the sleeves must be seared to prevent sleeve from Slide the sleeve over the Properly assemble the hose Secure the sleeve over hose sockets with a metal banding product. Max Hose OD Suggested Sleeve Sleeve that Sleeve Hose Size Part Number (in) can accept (in) as a -4FF90754-79 -4FF90754-91 -6FF90754-98 -6FF90754-106 -6FF90754-122 -8FF90754-142 -10FF90754-157 -10FF90754-173 -12FF90754-185 -16FF90754-209 -16FF90754-219 -20FF90754-238 -20FF90754-288 -20FF90754-366 -24 Table 2: Guardian Sleeve Selection Chart
