Rockbolts and cables - Rocscience Inc.
se of light 'safety' bolts, the . amount of tension applied is not critical and tightening the nut with a conventional wrench or with a pneumatic torque wrench is adequate. Where the bolts are required to carry a significant load, it is generally recommended that a tension of approximately
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Rock mass properties - Rocscience Inc.
www.rocscience.comcoefficient of determination 2 r are calculated from: n x ... The influence of sample size upon rock strength has been widely discussed in geotechnical literature and it is generally assumed that there is a significant reduction in strength with increasing sample size. Based upon an analysis of published data, Hoek and
Properties, Determination, Mass, Rocks, Strength, Rock strength, Rock mass properties
DIPS Tutorial - Rocscience Inc.
www.rocscience.comDips Plotting, Analysis and Presentation of Structural Data Using Spherical Projection Techniques User’s Guide 1989 - 2002 Rocscience Inc.
Rock Mechanics - an introduction for the practical engineer
www.rocscience.comwould initiate under various conditions13 14. Figure 4 illustrates the remarkable agreement between the predicted and observed fracture behaviour of slate specimens subjected to uniaxial compression. It will be noted that the highest strength of slate can be as much as four times its lowest strength,
Introduction, Practical, Engineer, Under, Mechanics, Rocks, Compression, Uniaxial, Uniaxial compression, Rock mechanics an introduction for the practical engineer
Hoek-Brown failure criterion – 2002 Edition
www.rocscience.comHoek and Brown [1, 2] introduced their failure criterion in an attempt to provide input data for the analyses required for the design of underground excavations in hard rock. The criterion was derived from the results of research into the brittle failure …
Failure, Brown, Criterion, Hoke, Brown failure criterion, Failure criterion
License Server Installation and Activation
www.rocscience.comAfter a short wait runtime installation should finish with the message “Operation successfully completed”. If errors occur instead, please take screen captures and send them to support@rocscience.com for further assistance. Reopen software activation utility and you should now be able to proceed with product activation. If you still
Installation, Server, Activation, Server installation and activation
Examine2D - Rocscience Inc.
www.rocscience.comFor information on any SLIDE options which are not covered in the SLIDE tutorials, consult the SLIDE Help system. Reference Detailed reference information on all of the options in the SLIDE program is found in the SLIDE Help system. To access the Help system: Select: Help → Help Topics in either the SLIDE Model or SLIDE Interpret programs.
Silent Installation from a setup.exe file
www.rocscience.comSilent Installation from a setup.exe file The USB key containing the suite of Rocscience software has a folder structure where the top level folder is the name of the product, the subfolder is a folder called install. Inside this folder is a setup.exe installation program.
Rock mass classification - Rocscience Inc.
www.rocscience.com1. Rock mass classification Introduction During the feasibility and preliminary design stages of a project, when very little detailed ... general tunnelling approach known as the New Austrian Tunnelling Method. ... - 3.3 Jv (1) where . J.
SUPPORT IN UNDERGROUND HARD ROCK MINES
www.rocscience.comWood, Senior Engineer, Golder Associates, Vancouver, British Columbia, Canada ... Introduction Rock support is the term widely used to describe the procedures and materials used to improve the stability and maintain the load bearing capacity of rock near to the boundaries of an underground excavation. In this paper, a distinction is drawn
Support, Woods, Mines, Underground, Hard, Rocks, Support in underground hard rock mines
Related documents
Design of Bolts in Shear-Bearing Connections per AISC LRFD ...
www.pdhonline.comreferred to as tension control, TC, twist-off, or torque-and-snap fasteners. High-Strength bolts range in diameter from ½ to 1 ½ in. For bolts larger than 1 ½ in the AISC allows the use of ASTM A449 provided that they are not used in slip-critical connections. b) Unfinished Bolts
Specification for Structural Joints Using ASTM A325 or ...
www.boltcouncil.orgBolts A325 9.4 A490 11.3.2 or 11.4.2 Twist-off-type tension control bolt assemblies F1852 13.4 Nuts A563 9.2 Washers F436 9.2 Compressible-washer-type direct tension indicators F959 10.2.2 Manufacturer. The party or parties that produce the components of the fastener assembly.
Tension Control Bolts Ltd Brochure
www.tcbolts.comWhilst this information is provided in good faith, no person from Tension Control Bolts Ltd shall be under any responsibility or liability in respect of errors or information that is found to be incorrect or for any reliance the user may place on it. 8 Specifications, mechanical properties and standards for washers ),+11")
Anchoring To Concrete - PDHonline.com
pdhonline.comCast-in anchors are of three (3) types, headed bolts, headed studs, and hooked bolts, installed in place prior to concrete placement. Cast-in gives greater control, but less flexibility Headed bolts are cylindrical threaded steel bars terminated in the concrete either by an integral head or nut, either of which may include a washer or plate. Care
ANCHORAGE PULL TESTING FOR FULLY GROUTED ROOF …
www.cdc.gov1In addition, the roof bolts may be intact, but the support system can fail if the bolts are too short, allowing the roof to fail above them; or the bolts fail to provide adequate skin control, allowing loose rock to create a hazard. 2In the literature, what …
Specification for Structural Joints Using High-Strength Bolts
www.aisc.orgAug 01, 2014 · F1136 coating on F1852 and F2280 bolts was deleted from Table 2.1 in recognition that this coating has not been approved by ASTM for use on TC bolts. Slip critical equations in Section 5.4 were updated for consistent with the AISC Specification. Clarification language was provided for approval requirements for hole sizes other