SAVE THESE INSTRUCTIONS - Confer Plastics

1 MODEL #7200 ROLLGUARD A-FRAME LADDERLADDER MUST BE ATTACHED TO POOL FRAME. DO NOT USE WITH INFLATABLE POOLSASSEMBLY AND INSTALLATION MANUALP roudly Made in bySAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNERUS Patent Numbers8,191,6828,191,6818,202, 1 8/14/13 4:58 PM Page 1 HandrailsRight BridgeLeft Bridge(behind the ROLLGUARD )DeckHardware Bag4 - Plug2 - 1/4" Flat Washer6 - #10 x 1-1/4" Self Tapping Screw4 - 1/4" Hex Nut 2 - 1/4 - 20 x 3-1/2" Bolt1 - Padlock1 - Instruction sheet2 - 1/4 - 20 x 1 BoltTools Needed for Assembly1 - Rubber Mallet1 - Cordless Drill w/Phillips Driver1 - Garden Hose1 - 1/4" Drill Bit1 - Phillips Screwdriver1 - PliersHelpful Hints:1). Assemble the ladder by laying it down on a smooth flat ). All ten treads are the same, but must be installed tab marked minus [-] into tread lockopening marked minus [-] and tab marked plus [+] into tread lock opening marked plus [+] on the MUST NOT BLOCK THE ROLLGUARD TRACKS LOCATED ON THE INSIDE AND OUTSIDE ).

2 The ROLLGUARD locking assembly is pre-installed on the left ). Slide the ROLLGUARD into track, grab handle #7200 ROLLGUARD A-FRAME LADDERL adder must be attached to pool frame - do not use with inflatable poolsASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLYP arts List4 - Handrail1 - ROLLGUARD 1 - Deck1 - Outside Left Rail (OL)1 - Left Bridge with lock assembly1 - Outside Right Rail (OR)1 - Right Bridge1 - Inside Left Rail (IL)2 - Stabilizer Rail1 - Inside Right (IR)10 - Ladder TreadIf missing parts call - Toll free - 800-635-3213 or Rail(OR)ROLLGUARD OutsideLeft Rail(OL)InsideRight Rail(IR)Inside Left Rail (IL) 1 8/14/13 4:58 PM Page 2 STEP 1:INSIDE LADDERT ools needed:rubber malletParts needed:1- Inside left rail (marked IL at the top)1- Inside right rail (marked IR at the top)4- Ladder treads#1: Lay IL rail on flat surface.#6: Lay IR rail on flat surface.

3 #7: Lift/rotate and align tread tabsto fit into rail #9: Do Not Install bottomtread until Step 4!#8: Tap all 4 treads downuntil #2: Correct, tap downuntil seated, note track isnot , do not block track.#3-5: Install 3 more treads, for a total of 4, see above 1 8/14/13 4:58 PM Page 3 STEP 2:OUTSIDE LADDERT ools needed:rubber malletParts needed:1- Outside left rail (marked OL at the top)1- Outside right rail (marked OR at the top)5- Ladder treads#9: Installbottom : Bottomtread will notbe flush withladder leg.#10: Outsideladder finished!#7: Lift/rotate and align tread tabsto fit into rail #8: Tap all 4 treads downuntil #2: Correct, tap downuntil seated, note track isnot #1: Lay OL rail on flat surface.#3-5: Install 3 more treads, for a total of 4, see above pictures.#6: Lay OR rail on flat , do not block 1 8/14/13 4:58 PM Page 4 STEP 3:HANDRAILS/DECKT ools needed:rubber mallet, cordless drill w/Phillips driverParts needed:1- Deck4- Handrails1- Left bridge with lock assembly1- Right bridge2- #10 x 1-1/4 self tapping screws2- 1/4 - 20 x 1 Bolts2- 1/4 - 20 Hex Nuts#1-3: Push handrails up through bottom of deck leaving about 3 exposed.

4 #4: Align the inside/outsiderails with deck/handrail.#5-6: Partially slide deck down locking handrails onto ladder sections. #7: Install right and left ladder bridges.#8: Using the 1/4 - 20 x 1 screws and hex nuts providedattach both outside bridgetabs to the outside ladder railsmarked OL & OR. Insertscrews through from theinside and fasten with hexnuts on the outside of rail.#10: Overlap the flat sections at topof the handrails and connect using1-#10 x 1-1/4 self tapping for other handrail.#9: Finish tapping deck allthe way down until engagedon to 1 8/14/13 4:58 PM Page 5 STEP 4:INSTALLING ROLLGUARD Tools needed:rubber malletParts needed:1- ROLLGUARD 1- Ladder tread#1: With the ladder laying on it s side, slide the ROLLGUARD into track, grab handle first.#2-6: Slide ROLLGUARD around to other side of ladder.#4#5#6#7-8: Install bottom tread. IMPORTANT: this bottom treadMUST be installed to block the track, ROLLGUARD mustnot come in contact with pool : Bottom tread will not be flush with ladder rail.

5 Treadwill extend past the bottom of ladder 1 8/14/13 4:58 PM Page 6 STEP 5:PLACING LADDER IN POOLT ools needed:garden hose, cordless drill w/Phillips driver 1/4 drill bit, Phillips screwdriver, pliersParts needed:4- cap plugs2- Stabilizer Rails2- 1/4-20 x 3-1/2 bolts, washers and hex nuts1- PadlockCHOOSE A LOCATION THAT IS LEVEL AND IN FULL VIEW. POOL MUST HAVECOMPETENT ADULT SUPERVISION AT ALL TIMES WHEN IN USE.#1: With ROLLGUARD in closed position, carefully lift the inside ladder section over the pool wall.#2: Using garden hose, fill onlythe 2 inside rails with waterthrough the openings and capwhen full. As the rails are beingfilled, the ladder will start to sink.#3: Tilt the ladder from sideto side to get all the air outof treads. As the treads fillwith water, the ladder willcontinue to sink, this maytake several minutes.#4: The inside of the pool laddermust be positioned as close to theinside of the pool wall as possible,this will keep swimmers from goingbehind ladder.

6 DO NOT LEAVE ALARGE GAP BETWEEN INSIDEOF POOL WALL AND , place one of the stabilizer railson the pool top ledge, align theraised ribs on the stabilizer rail withthe tracks on the ladder rails andattach using 2-#10 x 1-1/4 self tap-ping screws. Repeat for the secondstabilizer rail. TO STABILIZE YOURPOOL LADDER, STABILIZERRAILS MUST BE INSTALLEDPROPERLY AND REST ON THEPOOL TOP LEDGE.#5: TO KEEP POOL LADDER INPLACE, STABILIZER RAILS MUST BE ATTACHED TO POOLTOP the stabilizer railsas locators and drill two 1/4 holesthrough the pool top ledge. Be care-ful not to damage the pool wall orliner. Fasten ladder to the pool using2-1/4-20 x 3-1/2 screws, washers,and nuts. If necessary, Stabilizer railcan be reversed and attachedabove the recesses in rails toaccommodate taller pools#6: The ladder is in the closed position when the ROLLGUARD ispulled down covering the outside laddertreads.

7 To lock, push in the roll guardlocking tab located on the left properly locked, the ROLL-GUARD will not lift up. Install the padlock through the locking tab hole. WHEN POOL IS NOT IN USE THEROLLGUARD MUST BE IN CLOSEDPOSITION AND LOCKED.#7: To open pool ladder, remove the lockand pull locking tab out. Lift up on the ROLLGUARD and slide around to theinside of pool ladder, push locking tabback in and POOL IS IN USE, THEROLLGUARD MUST REMAINON INSIDE OF POOL ANDLOCKED. THE ROLLGUARD WILL PREVENT SWIMMINGTHROUGH INSIDE rails with waterusing garden hoseOptional locklocation (if needed). 1 8/14/13 4:58 PM Page 797 Witmer RoadNorth Tonawanda, New York 14120-2421 Toll Free in MADE IN THE by:IMPORTANTFOR YOUR SAFETY* Check the contents of the carton with the Parts listfor this ladder.*If any parts are missing call Toll Free - 800-635-3213 or visit our web site at: *DO NOTattempt to assemble or install the ladder if there are ANYshortages of parts or hardware.

8 *For proper assembly and installation follow allinstructions in the sequence shown.*Before using the product, after assembly and installation, go over the INSTRUCTIONS and proceduresagain to make sure nothing has been overlooked.*Be sure and safe. The manufacturer IS NOTresponsible for improper assembly, installation and RULES*Locate ladder on a solid base.*One person on the ladder at a time.*Ladder MUSTbe installed per manufacturer s INSTRUCTIONS .*DANGER:No Jumping or Diving from ladder.*Face ladder when entering and leaving pool.*To prevent entrapment or drowning DO NOTswim through, behind or around ladder.*Ladder to be used as a swimming pool ladder only.*Weight limit - 300 lbs maximum*Warning:Exceeding the maximum weight restriction may cause the ladder to fail.*When ladder is not in use pull down roll guard to cover outside ladder treads and lock using padlock.*Consult your local Building Department beforeinstallation of your pool and equipment.

9 *DANGER:Use a cordless drill for assembly and installation. NEVER use an electric drill in or around the ESEDMAINTENANCE:Check the padlock for proper operation and lubricate if necessary. When pool is not inuse ROLLGUARD must be in closed position and :Unfasten the ladder from pool top seat and remove from the water. Remove the plugs andlay ladder on its side to drain. It will take several minutes for the water to drain out of the ladder rails and small amount of water left in ladder will not cause any damage. Replace the plugs so they won t get ). Confer Plastics , INC. FIVE YEAR WARRANTYC onfer Plastics , their swimming pool ladders and steps to be free fromdefects in workmanship for five years from date of NOT RETURN DEFECTIVE PART TO DEALERE-MAIL Confer Plastics AT: PICTURE [S] OF DEFECTIVE PART, A BRIEF DESCRIPTION OF PROBLEM, PROOF OF PURCHASE AND YOUR CONTACT INFORMATION.

10 INFORMATION MAY ALSO BE FAXED TO Confer Plastics AT:716-694-3102OR MAILED TO THE ADDRESS BELOW. UPON REVIEW OF THE INFORMATION YOU WILL BE NOTIFIED IF PART IS COVERED UNDER THE WARRANTY AND THE SHIPPING/HANDLING warranty gives you specific legal rights, and you may also have other rights which may vary from state to Plastics , Witmer RoadNorth Tonawanda, 14120-24213-00-7200CP-7200 Rev 08 1 8/14/13 4:58 PM Page 8