Si5345/44/42 Rev D Data Sheet - Silicon Labs

1 Si5345/44/42 Rev D data Sheet 10-Channel, Any-Frequency, Any-Output Jitter Attenua- KEY FEATURES. tor/Clock Multiplier Generates any combination of output These jitter attenuating clock multipliers combine fourth-generation DSPLL and frequencies from any input frequency MultiSynth technologies to enable any-frequency clock generation and jitter attenu- Ultra-low jitter of 90 fs rms ation for applications requiring the highest level of jitter performance. These devices External Crystal: 25 to 54 MHz are programmable via a serial interface with in-circuit programmable non-volatile memory (NVM) so they always power up with a known frequency configuration.

2 Input frequency range They support free-run, synchronous, and holdover modes of operation, and offer Differential: 8 kHz to 750 MHz both automatic and manual input clock switching. The loop filter is fully integrated LVCMOS: 8 kHz to 250 MHz on-chip, eliminating the risk of noise coupling associated with discrete solutions. Fur- Output frequency range thermore, the jitter attenuation bandwidth is digitally programmable, providing jitter Differential: 100 Hz to 1028 MHz performance optimization at the application level. Programming the Si5345/44/42 is LVCMOS: 100 Hz to 250 MHz easy with Skyworks' ClockBuilder Pro software.

3 Factory preprogrammed devices Meets EEC Option 1, 2 (SyncE). are also available. Highly configurable outputs compatible with LVDS, LVPECL, LVCMOS, CML, and HCSL. Applications: with programmable signal amplitude OTN muxponders and transponders Si5345: 4 input, 10 output, 64-QFN 9 9 mm Si5344: 4 input, 4 output, 44-QFN 7 7 mm 10/40/100 G networking line cards Si5342: 4 input, 2 output, 44-QFN 7 7 mm GbE/10 GbE/100 GbE Synchronous Ethernet (ITU-T ). Carrier Ethernet switches SONET/SDH line cards Broadcast video Test and measurement ITU-T (SyncE) compliant 25-54 MHz XTAL. XA XB. Si5342. OSC MultiSynth INT OUT0. MultiSynth INT OUT1.

4 IN0 FRAC. MultiSynth INT. Si5344. OUT2. IN1 FRAC DSPLL. 4 Input MultiSynth INT OUT3. Clocks Up to 10. IN2 FRAC MultiSynth INT OUT4 Output Clocks INT OUT5. IN3/FB_IN FRAC. INT OUT6. INT OUT7. Si5345. INT OUT8. Status Flags Status Monitor INT OUT9. I2C / SPI Control NVM. Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 1 Rev. Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice November 30, 2021 1. Si5345/44/42 Rev D data Sheet Features List 1. Features List The Si5345/44/42 Rev D features are listed below: Generates any combination of output frequencies from any Optional zero delay mode input frequency Fastlock feature for low nominal bandwidths Ultra-low jitter of 90 fs rms Glitchless on the fly output frequency changes Input frequency range DCO mode: as low as ppb step size Differential: 8 kHz 750 MHz Core voltage LVCMOS: 8 kHz 250 MHz VDD: V 5%.

5 Output frequency range VDDA: V 5%. Differential: 100 Hz to 1028 MHz Independent output clock supply pins LVCMOS: 100 Hz to 250 MHz V, V, or V. Programmable jitter attenuation bandwidth: Hz to 4 kHz Serial interface: I2C or SPI. Meets EEC Option 1, 2 (SyncE). In-circuit programmable with non-volatile OTP memory Highly configurable outputs compatible with LVDS, LVPECL, LVCMOS, CML, and HCSL with programmable signal ampli- ClockBuilder Pro software simplifies device configuration tude Si5345: 4 input, 10 output, 64-QFN 9 9 mm Status monitoring (LOS, OOF, LOL) Si5344: 4 input, 4 output, 44-QFN 7 7 mm Hitless input clock switching: automatic or manual Si5342: 4 input, 2 output, 44-QFN 7 7 mm Locks to gapped clock inputs Temperature range: 40 to +85 C.

6 Free-run and holdover modes Pb-free, RoHS-6 compliant Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 2 Rev. Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice November 30, 2021 2. Si5345/44/42 Rev D data Sheet Ordering Guide 2. Ordering Guide Ordering Part Number Number of In- Output Clock Frequency Supported Frequency Temperature Package (OPN) put/Output Clocks Range (MHz) Synthesis Modes Range Si5345. Si5345A-D-GM1, 2 to 1028 MHz Integer and Si5345B-D-GM1, 2 to 350 MHz Fractional 64-QFN. 4/10 40 to 85 C. Si5345C-D-GM1, 2 to 1028 MHz 9 9 mm Integer Only Si5345D-D-GM1, 2 to 350 MHz Si5344.

7 Si5344A-D-GM1, 2 to 1028 MHz Integer and Si5344B-D-GM1, 2 to 350 MHz Fractional 44-QFN. 4/4 40 to 85 C. Si5344C-D-GM1, 2 to 1028 MHz 7 7 mm Integer Only Si5344D-D-GM1, 2 to 350 MHz Si5342. Si5342A-D-GM1, 2 to 1028 MHz Integer and Si5342B-D-GM1, 2 to 350 MHz Fractional 44-QFN. 4/2 40 to 85 C. Si5342C-D-GM1, 2 to 1028 MHz 7 7 mm Integer Only Si5342D-D-GM1, 2 to 350 MHz Si5345/44/42 -D-EVB. Si5345-D-EVB. Evaluation Si5344-D-EVB . Board Si5342-D-EVB. Notes: 1. Add an R at the end of the OPN to denote tape and reel ordering options. 2. Custom, factory preprogrammed devices are available. Ordering part numbers are assigned by Skyworks and the ClockBuilder Pro software.

8 Custom part number format is Si5345A-Dxxxxx-GM where xxxxx is a unique numerical sequence representing the preprogrammed configuration. Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 3 Rev. Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice November 30, 2021 3. Si5345/44/42 Rev D data Sheet Ordering Guide Figure Ordering Part Number Fields Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 4 Rev. Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice November 30, 2021 4. Table of Contents 1.

9 Features List .. 2. 2. Ordering Guide .. 3. 3. Functional Description.. 7. Frequency Configuration .. 7. DSPLL Loop Bandwidth .. 7. Fastlock Feature .. 7. Modes of Operation .. 7. Initialization and Reset .. 8. Freerun Mode .. 8. Lock Acquisition Mode .. 8. Locked Mode .. 8. Holdover Mode .. 9. External Reference (XA/XB) .. 9. Digitally Controlled Oscillator (DCO) Mode ..10. Inputs (IN0, IN1, IN2, IN3) ..10. Manual Input Switching (IN0, IN1, IN2, IN3) ..10. Automatic Input Selection (IN0, IN1, IN2, IN3) ..11. Hitless Input Switching ..11. Ramped Input Switching ..11. Glitchless Input Switching ..11. Input Configuration and Terminations.

10 12. Synchronizing to Gapped Input Clocks ..13. Fault Monitoring ..13. Input LOS Detection..14. XA/XB LOS Detection ..14. OOF Detection ..14. LOL Detection ..15. Interrupt Pin (INTRb) ..16. Outputs ..16. Output Crosspoint ..17. Output Signal Format ..17. Differential Output Terminations ..18. LVCMOS Output Terminations ..18. Programmable Common Mode Voltage For Differential Outputs ..18. LVCMOS Output Impedance Selection ..19. LVCMOS Output Signal Swing ..19. LVCMOS Output Polarity ..19. Output Enable/Disable ..19. Output Driver State When Disabled ..19. Synchronous Output Disable Feature ..19. Zero Delay Mode ..20. Output Divider (R) Synchronization.