SOLVENTLESS EPOXY SEF-381. - ppglic.com.au

1 SOLVENTLESS EPOXY . GENERAL FEATURES: SEF-381. A VERSATILE FLOORING EPOXY COATING GENERIC TYPE: TWO COMPONENT. TOUGH ABRASION RESISTANT FILM POLYAMINE CURED EPOXY . SURFACE TO PREPARED CONCRETE. GOOD FLOW AND WETTING PROPERTIES. BE COATED: CHEMICALLY RESISTANT AND IMPERVIOUS PRODUCT SOLVENTLESS EPOXY . DESCRIPTION: FLOORING COMPOUND. PRINCIPAL USES: GENERAL PHYSICAL PROPERTIES AND APPLICATION. DATA: SUITABLE FOR FOOD PROCESSING AREAS AND FINISH Gloss INDUSTRIAL FLOORS WHERE A HYGIENIC. ENVIRONMENT AND CHEMICAL RESISTANCE IS COMPONENTS 2. IMPORTANT. HARDENER 381-9293 Pack B. THINNERS CLEAN UP ONLY. RESISTANCE PROPERTIES: R202- EPOXY Reducer. MIXING RATIO (V/V) parts SEF-381 Pack A. 1 part SEF-9293 Pack B. Heat: Good up to 120 C. Some discolouration may occur. POT LIFE 30 minutes at 25 C.

2 Abrasion: Excellent when fully cured. VOLUME SOLIDS % 100%. Water: Excellent resistance to fresh and salt water. FLASH POINT >100 C. Not recommended for immersion. RECOMMENDED DRY FILM. Solvent: Resists splash and spillage of hydrocarbon THICKNESS 250 microns solvents and alcohols. THEORETICAL 4-5 m /L depending on surface Chemical: Very good to dilute acids and to alkalis. COVERAGE profile Excellent resistance to mineral and vegetable oils. PRACTICAL COVERAGE Allow appropriate loss factor. Weathering: Excellent durability. Will chalk on exposure to ultra-violet light. This does not detract from DRYING TIME Light Traffic 24 hours other film qualities. (@ 25 C & 50 % RH) Full Cure 1 week Toxicity: Dry film non-harmful unless lead pigments used. Refer label for lead warning.

3 RECOAT Overnight APPLICATION Roller / Trowel COLOURS: Colour Range available THINNING Not required APPLICATION METHODS. Roller/Trowel: Apply a full even coat to the recommended film build. Clean up: R202 EPOXY Reducer. NOTE: Do not apply at temperatures less than 5 C, or when the relative humidity exceeds 85%, or if the surface temperature is within 3 C of the Dew Point. PACK SIZES SOLVENTLESS EPOXY SEF381 Part A, Litre in 4 Litre can SOLVENTLESS EPOXY SEF381 Part B, Litre in 2 Litre can SOLVENTLESS EPOXY SEF-381. COATING SYSTEM RECOMMENDATIONS. SURFACE PREPARATION SYSTEM DRY FILM THICKNESS. CONCRETE Brush Blast / Acid Etch BARSEAL EXS-461 25 microns PENETRATING SEALER. Flooring EPOXY FLOORING SEF381 125 microns (Very porous EPOXY FLOORING SEF381 125 microns substrate).

4 CONCRETE Brush Blast / Acid Etch EPOXY FLOORING SEF381 125 microns Flooring EPOXY FLOORING SEF381 125 microns * REFER to your Barrier Protective Coatings Representative for specific recommendations for your special application. HEALTH AND SAFETY. PACK A PACK B. UN NO. - UN NO. 2735. Flash Point 150 C Flash Point 101 C. Packaging Group - Packaging Group III. Keep away from all sources of heat and open flames. Do not smoke whilst handling. Wear suitable protective clothing to avoid contact with skin and eyes. Provide adequate ventilation during use and avoid breathing vapour. Do not spray in confined or poorly ventilated areas without the use of approved air supplied breathing apparatus. FIRST AID. Eyes: If paint splashed in eyes, irrigate with copious amounts of clean water for 15 minutes.

5 Seek medical aid if irritation persists. Skin: If paint splashed on skin, wash affected area thoroughly with soap and water. If irritation persists seek medical aid. Remove all contaminated clothing and launder before re-use. Inhalation: If affected by exposure to vapours, remove from area, keep at rest and seek medical aid if symptoms persist. Ingestion: If swallowed, give glass of water to drink and seek medical assistance. Do not induce vomiting. Consult separate Material Safety Data Sheet for more detailed Health and Safety information. REVISED: March 2009. This information is furnished without warranty, representation, inducement or licence of any kind except that it is accurate to the best of Protec Pty Ltd's knowledge or obtained by Protec Pty Ltd from sources believed by it to be accurate and Protec Pty Ltd does not assume any legal responsibility for use or reliance upon the same.

6 Customers are encouraged to conduct their own tests. This information is non-controlled. It is the responsibility of the user to ensure that the issue is current. Barrier Chemicals Pty. Ltd. is a wholly owned subsidiary of Protec Pty. Ltd.