Example: bachelor of science
TECHNICAL GUIDE - Georgia-Pacific Building Products
Dec 01, 2017 · For latest information and updates: Technical Service Hotline 1.800.225.6119 or www.gpgypsum.com CAUTION: For product fire, safety and use information, ... DensDeck Roof Board serving as an insulation thermal barrier overlayment with all joints staggered a min. of 6” (152 mm) from the plywood joints.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Guide: DensArmor Plus® High-Performance Interior ...
www.buildgp.comof Gypsum Panel Products” and ASTM C840 “Standard Specifi cation for Application and Finishing of Gypsum Board for Non-Fire Rated Construction.” For best results, abut DensArmor Plus panels against regular paper-faced drywall only at inside or outside
TECHNICAL GUIDE - Georgia-Pacific Building Products
www.buildgp.cominstallation. DensGlass Sheathing is the ideal substrate for a wide variety of air and water-resistive barriers including building wraps, fluid applied coatings, self-adhering membranes and spray foam applications. See page 10 for details. Easy to Handle DensGlass Sheathing is lightweight and easy to handle.
Technical Service Hotline 1.800.225.6119 or www.gpgypsum
www.buildgp.comassembly installation instructions). Primary Uses Because of the superior performance of DensGlass Sheathing, it is specified for exterior walls, ceilings and soffits in a wide variety of applications. These include exterior insulation and finish systems (EIFS); cavity brick or stone veneer applications;
Technical Service Hotline 1.800.225.6119 or www.densdeck
www.buildgp.commanufacturer’s specifications for full mopping applications and temperature requirements. ... * Testing was done in accordance with FM approvals 4470, Appendix C: Small Scale Tests, Membrane ... with the ANSI/UL 1256 Steiner Tunnel test. For additional information concerning
Densglass Shaftliner Area Walls Technical Guide
www.buildgp.comBuilding Code (IBC) Section 706, “Fire Walls.” The Area Separation Wall assembly using DensGlass Shaftliner panels is listed in the UL Fire Resistance Directory under UL Design U373 or U375, the ULC Fire Resistance Directory ULC Design No. W312 and the
Stamps/Signatures
www.buildgp.comFIRE SAFETY CAUTION Passing a fire test in a controlled laboratory setting and/or certifying or labeling a product as having a one-hour, two-hour, or any other fire resistance or protection rating and, therefore, as acceptable for use in certain …
SHAFTLINER FOR SHAFTWALL/STAIRWELL SYSTEMS
www.buildgp.comNote that the edges of the panel are beveled to help guide the panel into the slotted and tabbed section of the stud. 6. Progressively install succeeding studs and panels as described above until the wall section is enclosed. The final panel section may be secured with 1-5/8” (41 mm) Type S screws or tabs from the J track at 24” (610 mm) o ...
DensShield® Tile Backer Installation Instructions
www.buildgp.comDS001. Note: Shower pan or rubber membrane must be adequately sloped to the open drain or weep hole detail to permit proper water drainage. Leave a 1⁄89 (3 mm) gap between DensShield Tile Backer and the shower pan. • DensShield Tile Backer is not to be used in shower curbs. • DensShield Tile Backer panels can be installed in the shower
Related documents
Extruded Polystyrene (XPS) Rigid Foam Insulation Product ...
insulation.owenscorning.comProduct Data Sheet FOAMULAR® 250 Extruded Polystyrene (XPS) Rigid Foam Insulation • Provides a weather resistant barrier (when joints are sealed) to enhance the building’s resistance to air and moisture penetration Technical Information This product is combustible. A protective barrier or thermal barrier is required as specifi ed
Extruded Polystyrene (XPS) Rigid Foam Insulation Product ...
www.owenscorning.comProduct Data Sheet FOAMULAR® 150 Extruded Polystyrene (XPS) Rigid Foam Insulation • Provides a weather resistant barrier (when joints are sealed) to enhance the building resistance to air and moisture penetration. Technical Information This product is combustible. A protective barrier or thermal barrier is required as specifi ed
Thermafiber SAFB Mineral Wool Insulation
www.thermafiber.comThermafiber Insolutions® offers industry leading technical and engineering assistance to architects, specifiers, and contractors. These services include CAD drawings, engineering judgments, LEED® Credit Information, and product recommendations. Contact our technical services department at 1-888-834-2371 or email
Product Information Sheet Froth-Pak Insulation Spray Foam
www.dupont.comProduct Theoretical Yield, (1) board ft Kits ... * Froth-Pak™ Foam Insulation is a former product of The Dow Chemical Company. ** Actual cure time will depend on temperature, foam thickness, the specific nozzle used, etc. Product Information Sheet.
POLYISOCYANURATE FOAM SHEATHING CONTINUOUS …
www.jm.comTechnical specifications as shown in this literature are intended to be used as general guidelines only. Please refer to the Safety Data Sheet and product label prior to using this product. The physical and chemical properties of AP Foil-Faced Polyisocyanurate Continuous Insulation listed herein represent typical, average values ob-
AP Foil-Faced - Johns Manville
www.jm.comTechnical specifications as shown in this literature are intended to be used as general guidelines only. Please refer to the Safety Data Sheet and product label prior to using this product. The physical and chemical properties of AP Foil-Faced Polyisocyanurate Continuous Insulation listed herein represent typical, average values ob -
TECHNICAL DATA SHEET - Henry
henry.comThe technical and application information herein is based on the present state of our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be made as to a product’s suitability for a particular use or application and no warranty as to its accuracy, reliability or completeness either