Temposonics m - Vickers

1 Temposonics MagnetostrictivePosition SensorsM-SeriesAnalogTemposonics MHMeasuring length 50 - 2500 mmmSENSORSM agnetostriction The absolute Temposonics linearposition sensors are based on theMTS developed magnetostrictivemeasurement principle. That combi-nes various magneto-mechanicaleffects and uses the physical heightprecise speed-measurement of anultrasonic wave (torsion pulse in itssensor element) for position detec-ting. sensor integrated signal proces-sing transforms the measurementsdirectly into market standard contactless principle - an exter-nal movable magnet marks the posi-tion - eliminates the wear, noise anderroneous signal problems and gua-rantees the best durability withoutany factorTemposonics MH, the compactstainless steel position sensor isdesigned for installation into hydrau-lic cylinders, specifically for use inclevis head mobile cylinders or anyspace limited cylinder The sensor head, a robust housingwith built-in The pressure-proof sensor pipewith flange protects the internal sen-sing element, the waveguide fits into the bored piston The position magnet, only movingpart is mounted on the piston bot-tom.

2 This permanent magnet travelswearfree and contactless along thestationary sensor tube. Its magneticfield starts the measurement signalthrough the sensor s rod wall. Linear, Absolute Measurement in Hydraulic Cylinders Contactless Sensing with Highest Durability Minor Dimensions for Compact Mobile Hydrocylinders Replacing Potentiometers and Inductive Position Sensors Superior Accuracy: Linearity Tolerance better 0,04 % Repeatability 0,005 % Direct Analog Displacement Output: Current and Voltage Power Supply: 12 / 24 VDC EMC: Immunity against electromagnetic HF-fields up to 200 V/m Independent from Hydraulic LiquidCompact sensor for Mobile HydraulicsI 2 ITemposonics-MHAnalogMTS Sensors Technical DataInputMeasured Variables: Displacement Measuring Range: 50 - 2500 mm in 5 mm stepsOutputVoltage: 0 - 5 VDC / 0, 4,75 / 0,5 .. 4,5 VDC; (Controller input resistance RL: 10 kohm, short circuit-proof, electric strength up to 28 Vdc)Strom:4 - 20 mA (apparent power of the voltage transformer 250 Ohm with 12 V power supply,apparent power of the voltage transformer 500 Ohm with 24 V power supply)AccuracyResolution:Infinite, restricted by output rippleLinearity, uncorrected: < 0,04 % (Minimum 0,100 mm) Repeatability: < 0,005 % Frequency:> 1,25 kHzRipple: < 0,02 % conditionsMounting Position, sensor : Any orientationMagnet Speed: AnyOperating Temperature: -40 C.

3 +85 C (optinal 105 C)Dew Point, Humidity: 90 % rel. humidity, no condensationSealing: IP 65 Rod Pressure Rating: 300 bar, 450 bar peak pressure for 7 mm rod diameter350 bar, 530 bar peak pressure for 10 mm rod diameterShock Rating: 100 g (single hit) / IEC-Standard 68-2-27 Vibration Rating: 25 g / 5 kHz / IEC-Standard 68-2-6 EMC-Test: ISO 14982 Agricultural- and forest maschinesISO 7637-1/2/3 Road vehicles Immunity belong to ISO 11452-5: electromagnetic HF-fields up to 200 V/m CE certifiedEMC for railway vevicles DIN EN 50121-3-2 Form factor, MaterialMaterial sensor : Stainless steel / AISI 304 Magnet Type: Ring magnet InstallationMounting: Clearance fit flange 48 mmElectrical connectionsConnection Type: pigtailed PUR cable, 3 wires Input Voltage: 12 / 24 VDC (10 - 32 V)Ripple: < 1 % peak to peakCurrent Drain: < 60 mAElectric Strength.

4 500 V ( 0 V ground to machine ground)Polarity Protection: Up to -30 VDCO vervoltage Protection: Up to 36 VDCA nalog OutputTemposonics-MH sensors provide analog output of 0 -5 V. The analog output signal is proportional to the magnet position along the active measuring sensor measuring range is factory set and does not need recalibration. Since the outputs are direct, no signal-conditioning electronics are needed when interfacing withcontrollers or 3 ITemposonics-MHAnalogMTS Sensors Temposonics -MH - High Pressure Compact SensorMeasuring Range 50 - 2500 , the new compact stainless steel position sensor is designedfor installation into hydraulic cylinders, specifically for use in clevis head mobilecylinders or any space limited cylinder type sensors are ideal choices for a wide range of standard hydraulic cylin-ders. Magetostrictive displacement sensors, high quality cylinders and precisecontrol valves form ideal driving systems for technically demanding of mechanicsThe extremely rugged sensor consist of 3 main parts The sensor head, a robust housing with built-in electronics.

5 The pressure-proof sensor pipe (up to 350 bar) with flange protects theinternal sensing element, the waveguide system. It fits into the bored piston rod. The position magnet, only moving part is mounted on the piston bottom. This permanent magnet travels wearfree and contactless along the stationary sensor tube. Its magnetic field starts the measurement signal through the sensors rod in mm. Technical alterations reservedMeasuring Range 50 - 2500O-Ring 40,87 x 3,53 NBR80 Backupring 42,6 x 48 x 1,4 PTFEI ntegral cable1 m pigtailedSensor stroke 7 / 1063,5302111,5 48 f7 30 24AA22,6> 18 Position magnet20,5 Mounting bore 48 H8 Ra 0,8 Active Stroke LengthNull Position 13,5 4,2 oncircle 24 Height: 8 mm 33 Height: 8 mm 13,5 25,4 Ring magnet OD33 Part No. 201 542-2 Composite PA-Ferrite-GF20 Weigth ca. 14gOperating temperature:-40 .. +100 CPart No. 401 032 Composite PA-FerriteWeigth ca. 10gOperating temperature:-40 .. +100 CRingmagnet OD17,4 Ring magnet OD25,4 Part No.

6 400 533 Composite: PA-FerriteWeigth ca. 10gOperating temperature:-40 .. +100 C13,5 17,4 Height: 8 mmPosition MagnetsI 4 ITemposonics-MHAnalogMTS Sensors Mobile hydraulic cylinder with built-in Temposonics -MH30 Position magnet>18I 5 ITemposonics-MHAnalogMTS Sensors InstallationThe robust Temposonics -MH sensor is due to its form factor,excellently suited for direct stroke measurement in standard compact position magnet, mounted on the piston bottom, drives contactlessly alongthe measuring stroke and marks exactly the position through the rod wall -independent of the used hydraulic fluid - that guarantees a longlife and trouble-free stainless steel rod model sensor can be mounted in any position via theclearance fit flange 48 sealing is by using an O-Ring and Backup-Ring in housing material should be used for the sensor mounting the mounting dimensions shown below into account is MagnetTo have a neat magnetic field for measuring, non-magnetizablematerial must be used for the position magnet mounting components (screws.)

7 Spacers, retaining ring etc.).For further details according to cylinder design please contact directly example: Mobile hydraulic cylinder with built-inTEMPOSONICS-MHNon-magnetizable materialMagnetizable materialO-Ring andBackup-RingPositionmagnetMeasurement in mm. Technical alterations reservedInstallation Notes Use a rod bush ( teflon) to prevent wear on the magnet andthe sensor pipe. The bore in the piston rod is dependent on hydraulic pressureand piston velocity etc. The minimum drilling must be 10 (7 mm rod) or 13 mm(10 mm rod). Do not exceed the peak Flange retaining with set screw DIN 914 M5x10maximum torque 0,5 NmExample 1 Example 2 The sensor will be fixed with setscrewInstallation Versions4,57,514,5445 min. 5nonferrous spacerPosition magnet15 > 32 mmI 6 ITemposonics-MHAnalogMTS Sensors Cable outletPUR-cable, 3 x 0,34 mm2, 4,5 - 6 mm, flexible, oil resistinggreenbrownwhiteWiringWire colorSignalgreenOutput: Voltage rangebrown+12/24 VDCwhiteDC Ground (0V)6 pin DIN wall mount flange receptacle for installationin customized cylinder end-capPart No.

8 ST C0 9131 S06 WiringPinWire colorSignal1greenOutput: Voltage range2------NC3 ------NC4------NC5brown+12/24 VDC6whiteDC Ground (0V)26 3,220108172620 Male connector (Accessories)Mounting bore 17,2124563 Front face of pin insertor rear of female insertMeasurement in mm. Technical alterations reservedI 7 ITemposonics-MHAnalogMTS Sensors TemposonicsMH= Hydraulic rodStyleC= Pressure-fit flange housing 48 mm / Rod- 10 mmD= Pressure-fit flange housing 48 mm / Rod- 7 mm (available on request)Measuring Range (Order Length)0050 - 2500 mm in 5 mm stepsConnection TypeS01= 1 m integral PUR cable, pigtailed (3 wires)S02= 2 m cable lengthS03= 3 m cable lengthInput Voltage3= +12/24 VDCS ignal OutputV10= 0 - 5 VV11= 0,25 - 4,75 V V12= 0,5 - 4,5 VM3 Scope of Delivery- Position sensor - O-Ring- Backup-RingPls. order magnets see (selection)Part magnet OD33201 542-2 Ring magnet OD25,4400 533 Ring magnet OD17,4401 0326 pin wall mount receptacle, maleSt C0 9131 S06MH MTS Temposonics M-Series Temposonics MH Analog 20102005e - Alterations reservedTemposonics-MHAnalogmSENSORSG ermanyMTS sensor TechnologieGmbH & Co.

9 KGAuf dem Sch ffel 9D-58513 L denscheidTel.: +49-2351-9587-0 Fax: Systems CorporationSensors Division3001 Sheldon DriveCary, NC 27513, USATel.: +1-919-677-0100 Fax: Sensors Technology Aihara-cho, Machida-shiTokyo 194-0211, JapanTel.: +81-42-775-3838 Fax: Hotline: 01805 - mtssensor