USB-6008 Specifications - National Instruments

1 SPECIFICATIONSUSB-60088 AI (12-Bit, 10 kS/s), 2 AO (150 Hz), 12 DIO USB Multifunction I/ODeviceDefinitionsWarranted Specifications describe the performance of a model under stated operatingconditions and are covered by the model following characteristic Specifications describe values that are relevant to the use of themodel under stated operating conditions but are not covered by the model warranty. Typical Specifications describe the performance met by a majority of models. Nominal Specifications describe an attribute that is based on design, conformance testing,or supplemental are Typical unless otherwise are valid at 25 C unless otherwise InputAnalog inputsDifferential4 Single-ended8, software-selectableInput resolutionDifferential12 bitsSingle-ended11 bitsMaximum sample rate (aggregate)10 kS/s, system dependentConverter typeSuccessive approximationAI FIFO512 bytesTiming ns (24 MHz timebase)Timing accuracy100 ppm of actual sample rateInput rangeDifferential 20 V1, 10 V, 5 V, 4 V, V, 2 V, V, 1 VSingle-ended 10 VWorking voltage 10 VInput impedance144 k Overvoltage protection 35 VTrigger sourceSoftware or external digital triggerSystem noise2 Differential 20 V range5 mVrms 1 V mVrmsSingle-ended, 10 V range5 mVrmsTable 1.

2 Absolute Accuracy at Full Scale, DifferentialRange (V)Typical at 25 C (mV)Maximum over Temperature (mV) Input voltages may not exceed the working voltage 20 V means that |AI+ (AI )| 20 V. However, AI+ and AI must both be within 10 V ofGND. Refer to the Taking Differential Measurements section of the NI USB-6008 /6009 User Guidefor more noise measured at maximum sample | | USB-6008 SpecificationsTable 2. Absolute Accuracy at Full Scale, Single-EndedRange (V)Typical at 25 C (mV)Maximum over Temperature (mV) OutputAnalog outputs2 Output resolution12 bitsMaximum update rate150 Hz, software-timedOutput range0 V to +5 VOutput impedance50 Output current drive5 mAPower-on state0 VSlew rate1 V/ sShort circuit current50 mAAbsolute accuracy (no load)Typical7 mVMaximum at full mVDigital I/ODigital I/O linesP0.< >8 linesP1.

3 < >4 linesDirection controlEach channel individually programmable asinput or outputOutput driver type3 Open collectorCompatibilityTTL, LVTTL, CMOSA bsolute maximum voltage V to V with respect to GNDPull-up k to 5 VPower-on stateInput3 This document uses NI-DAQmx naming conventions. Open-drain is called open collector andpush-pull is called active Specifications | National Instruments | 3 Table 3. Digital Logic LevelsLevelMinimumMaximum Input low VInput high VInput leakage current 50 AOutput low voltage (I = mA) VOutput high voltage, active drive (I = mA) VOutput high voltage, open collector (I = mA, nominal) VOutput high voltage, open collector (I = mA, with externalpull-up resistor) V External Voltage+5 V output (200 mA maximum)Minimum+ VTypical+5 V+ V output (1 mA maximum)+ V+ V maximumReference temperature drift50 ppm/ C maximumEvent CounterNumber of counters1 Resolution32 bitsCounter measurementsEdge counting (falling-edge)Counter directionCount upPull-up k to 5 VMaximum input frequency5 MHzMinimum high pulse width100 nsMinimum low pulse width100 nsInput high VInput low V4 | | USB-6008 SpecificationsBus InterfaceUSB specificationUSB full-speed (12 Mb/s)

4 Power RequirementsUSB, VDC to VDCT ypical80 mAMaximum500 mAUSB suspendTypical300 AMaximum500 APhysical CharacteristicsDimensionsWithout mm mm mm( in. in. in.)With mm mm mm( in. in. in.)WeightWithout connectors54 g ( oz)With connectors84 g (3 oz)USB connectorUSB series B receptacle (1)I/O connectorsType16-position screw terminal plugs (2)Screw-terminal wiring16 AWG to 28 AWGT orque for screw N m to N m( lb in. to lb in.)If you need to clean the module, wipe it with a dry Specifications | National Instruments | 5 Figure 1. USB-6008 mm( in.) mm( in.) mm( in.) mm( in.) mm( in.) mm( in.)Safety VoltagesConnect only voltages that are within these 30 V max, Measurement Category IMeasurement Category I is for measurements performed on circuits not directly connected tothe electrical distribution system referred to as MAINS voltage.

5 MAINS is a hazardous liveelectrical supply system that powers equipment. This category is for measurements of voltagesfrom specially protected secondary circuits. Such voltage measurements include signal levels,special equipment, limited-energy parts of equipment, circuits powered by regulatedlow-voltage sources, and electronicsCaution Do not use this module for connection to signals or for measurementswithin Measurement Categories II, III, or IVNote Measurement Categories CAT I and CAT O (Other) are equivalent. These testand measurement circuits are not intended for direct connection to the MAINS building installations of Measurement Categories CAT II, CAT III, or CAT | | USB-6008 SpecificationsEnvironmentalTemperature (IEC 60068-2-1 and IEC 60068-2-2)Operating0 C to 55 CStorage-40 C to 85 CHumidity (IEC 60068-2-56)Operating5% RH to 95% RH, noncondensingStorage5% RH to 90% RH, noncondensingPollution Degree (IEC 60664)2 Maximum altitude2,000 mIndoor use product is designed to meet the requirements of the following electrical equipment safetystandards for measurement, control, and laboratory use: IEC 61010-1, EN 61010-1 UL 61010-1, CSA No.

6 61010-1 Note For UL and other safety certifications, refer to the product label or the OnlineProduct Certification CompatibilityThis product meets the requirements of the following EMC standards for electrical equipmentfor measurement, control, and laboratory use: EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity EN 55011 (CISPR 11): Group 1, Class A emissions EN 55022 (CISPR 22): Class A emissions EN 55024 (CISPR 24): Immunity AS/NZS CISPR 11: Group 1, Class A emissions AS/NZS CISPR 22: Class A emissions FCC 47 CFR Part 15B: Class A emissions ICES-001: Class A emissionsNote In the United States (per FCC 47 CFR), Class A equipment is intended foruse in commercial, light-industrial, and heavy-industrial locations. In Europe,Canada, Australia and New Zealand (per CISPR 11) Class A equipment is intendedfor use only in heavy-industrial Specifications | National Instruments | 7 Note Group 1 equipment (per CISPR 11) is any industrial, scientific, or medicalequipment that does not intentionally generate radio frequency energy for thetreatment of material or inspection/analysis For EMC declarations and certifications, and additional information, refer tothe Online Product Certification Compliance This product meets the essential requirements of applicable European Directives, as follows: 2014/35/EU; Low-Voltage Directive (safety) 2014/30/EU; Electromagnetic Compatibility Directive (EMC)Online Product CertificationRefer to the product Declaration of Conformity (DoC) for additional regulatory complianceinformation.

7 To obtain product certifications and the DoC for this product, visit , search by model number or product line, and click the appropriate link in theCertification ManagementNI is committed to designing and manufacturing products in an environmentally responsiblemanner. NI recognizes that eliminating certain hazardous substances from our products isbeneficial to the environment and to NI additional environmental information, refer to the Minimize Our Environmental Impactweb page at This page contains the environmental regulations anddirectives with which NI complies, as well as other environmental information not included inthis Electrical and Electronic Equipment (WEEE)EU Customers This symbol indicates that waste products should be disposed ofseparately from municipal household waste according to WEEED irective 2002/96/EC of the European Parliament and the Council on wasteelectrical and electronic equipment (WEEE).

8 All products at the end of their lifecycle must be sent to a WEEE collection and recycling center. Proper WEEE disposal reduces environmental impact and the risk to human health due topotentially hazardous substances used in such equipment. Your cooperation inproper WEEE disposal will contribute to the effective usage of natural resources. Forinformation about the available collection and recycling scheme in a particularcountry, go to | | USB-6008 Specifications RoHS National Instruments (RoHS) National Instruments RoHS (For information about China RoHScompliance, go to ) USB-6008 Specifications | National Instruments | 9 Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at forinformation on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of theirrespective companies.

9 For patents covering NI products/technology, refer to the appropriate location: Help Patents in yoursoftware, the file on your media, or the National Instruments Patent Notice at You can findinformation about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Referto the Export Compliance Information at for the NI global trade compliance policy and howto obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES ASTO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. Customers: The data contained in this manual was developed at private expense and is subject to the applicablelimited rights and restricted data rights as set forth in FAR , DFAR , and DFAR 2015 2017 National Instruments . All rights 1, 2017