User Manual - Norsk Elsykkel

1 User Manual Classic user 1 7/15/2016 4:57:43 PM. User Manual 1. Content of Shipping Carton Congratulations for purchasing a SmartMotion electric bicycle! In the eUrban and eCity box you will find the following In the e20 box you will find the following items: Please read this guide fully BEFORE using your electric bike. items: 1. SmartMotion electric bicycle 1. SmartMotion electric bicycle 2. Battery charger 2. Battery charger 3. Bottle cage 3. Bottle cage Contents 4. 2X Pedals 4. 2X Pedals 1. Contents of shipping carton 5. Tool kit (4mm, 5mm & 6mm allen key, 5. Tool kit (4mm, 5mm & 6mm allen key, 2. Assembly instructions 8mm/10mm spanner, 15mm spanner). 8mm/10mm spanner, 15mm spanner).

2 3. Safe Riding Recommendations 6. 2X keys for frame lock and battery lock 6. 2X keys for frame lock and battery lock 4. Maintenance & Adjustment 7. Elastic strap 7. Front light 5. Main Specifications 8. Front wheel quick release axle 6. Do's and Don'ts 9. Elastic strap 7. Display Panel 8. Display Panel Controls 9. Frame Lock and Seat 10. Battery instructions 11. Warranty 12. Service Checklist 13. Service Record Classic user 2-3 7/15/2016 4:57:55 PM. 2. Assembly Instructions 2. Assembly Instructions eCity & eUrban eCity & eUrban Your electric bike is shipped 85% assembled. Follow 1. Unpack 2. Fork b. Loosen the handle bar angle adjusting bolt these steps to get it ready and safe for you to ride.

3 A. Carefully lift the electric bike out from the carton a. Insert the handle bar stem into the steering (at the pivot point of your adjustable stem) two (two people recommended for this task). Cut the tube, turn it to align it with the forks correctly, then or three turns then adjust the stem angle to the To Prepare position comfortable for you. Then loosen the 2. nylon zip ties with suitable scissors and remove the fasten the centre screw using the 6mm allen key to We recommend that you familiarise yourself foam protection from the bike. This is a quill type stem that if set too handlebar clamp bolts and rotate the handlebar to with the bike parts before assembling. Gather all high can cause damage to your bicycle, decrease make sure the brake lever and lcd display positions required tools.

4 Be sure to work in a clean, dry space b. Remove the front wheel and mudguard from the your control and cause you to fall. Make sure the are at the correct angle, then fasten the two bolts to with plenty of room. You might wish to lay down a bike and put them aside. Carefully stand the bike Minimum-insertion mark is within the frame. Finally fasten the angle adjusting bolt to tarpaulin or old blanket to protect the bike during upright, resting on its forks when installing wheels. assembly. You may find it helpful to stand the bike frame on a block or sturdy box under the battery housing to work with it in an upright position. Please watch the balance when installing wheels. Do not activate the brakes until the bike is fully assembled.

5 Squeezing brake levers while calipers have no disc rotor between them can damage the brakes. Classic user 4-5 7/15/2016 4:57:57 PM. 2. Assembly Instructions 2. Assembly Instructions eCity & eUrban eCity & eUrban 3. Mudguard 4. Power Connection 5. Seat 6. Pedals Install the front mudguard and front light on the Finally connect the main cable exciting the frame Release the seat post clamp lever and set the Attach the pedals to the cranks, paying attention fork. Take off the bolt from the front fork, put the near the headtube to the handlebar components seat post height to the position which is suitable to the L or R marked on the pedal axles. Note: front mudguard hanger mount on the inside or cable, making sure the arrows align before pushing for you to comfortably reach the ground when you the pedals have opposing threads screw in the left outside of the fork then put the front light bracket the connectors together.

6 Are sitting on the bike, then refasten the seat post pedal counterclockwise and screw in the right pedal on. Put the bolt through the fork then fasten the clamp. The maximum height should be within the clockwise. Install L pedal counterclockwise and the bolt with a 5mm allen key and 10mm spanner. max height markings on the seatpost. right pedal clockwise. Then fasten the two mudguard stays to the forks. Finally connect the light cable to the front light. Classic user 6-7 7/15/2016 4:58:21 PM. 2. Assembly Instructions 2. Assembly Instructions eCity & eUrban e20. 7. Front wheel The e20 electric bike is shipped folded inside the carton 1. Unpack Assemble the front wheel quick release axle by and 95% assembled.

7 Follow these steps to get it ready a. Carefully lift the electric bike out from the carton pushing it through the hollow hub, making sure and safe for you to ride. (two people recommended for this task). Cut the that one spring is on each side of the hub. Then nylon zip ties with suitable scissors and remove the screw on the end nut several turns. Next, carefully To Prepare foam protection from the bike. We recommend that you familiarise yourself lift the bike front forks off the ground and lower the with the bike parts before assembling. Gather all forks onto the wheel axle, being careful the disc b. Unfold the main frame until the hinge joint is fully required tools. Be sure to work in a clean, dry space rotor fits correctly into the disc calipers (this job is closed and lock it by pushing alloy lock lever until with plenty of room.)

8 You might wish to lay down a best with 2 people). Tighten the non-rotor side nut it clamps against the frame. Then rotate the plastic tarpaulin or old blanket to protect the bike during finger tight and try to close the quick release lever. secondary lock down into the alloy lock lever. assembly. You may find it helpful to stand the bike Loosen or tighten the nut until it takes the correct frame on a block or sturdy box under the battery amount of force to close the lever. It should be hard housing to work with it in an upright position. to close, but not so hard you cannot fully close it. It Please watch the balance when installing wheels. must fully close (as in picture) otherwise the wheel may come loose, causing serious injury.

9 Note: if you are not well trained in cycle assembly, this procedure must be checked by a cycle technician. Classic user 8-9 7/15/2016 4:58:31 PM. 2. Assembly Instructions 2. Assembly Instructions e20 e20. 2. Handlebars b. Adjust the handlebar horizontal rotation if need- 3. Pedals 4. Seat a. Carefully unfold the handlebar stem post up into ed by lifting up the handlebar stem quick release Attach the foldable pedals to the cranks, paying Release the seat post clamp lever and set the seat its vertical position, then close the alloy lock lever lever, then twist the handle bar to the correct angle attention to the L or R marked on the pedal post height to the position which is suitable for against the stem post.

10 Finally rotate the plastic and press the quick release lever down again to axles. Install washer and screw in the L pedal you to comfortably reach the ground when you safety lock ring until it enters and locks the alloy lock. counterclockwise and the right pedal clockwise. See are sitting on the bike, then refasten the seat post lock lever closed. Adjust the vertical height of handlebar using the wellgo instructions for full details. clamp. The maximum height should be within the same procedure with the quick release lever down max height markings on the seatpost. on the mid section of the stem post. Classic user 10-11 7/15/2016 4:59:14 PM. 3. Safe Riding Recommendations 3. Safe Riding Recommendations 1.