Transcription of Vane Type Single Pump - Eaton
1 I-3165-SRevised 07 01 97 Vane Type Single Pump25/26/30/31 VQ Series - 20 DesignService DataVickers Vane PumpsCAPACITY(USGPM)SCREW(2 REQ D)PIN(2 REQ D)INLETSUPPORTPLATE SEALPACK(4 REQ D)FLEX-SIDEPLATE KITROTORVANE KIT(10 VANES &10 INSERTS) (INCLUDESBUSHING)433764S/A92395627059726 2152922710922648326984326985326986326987 3269882344702245254164394164404164414212 3241644241705241645242157042157142157242 15734215744216454216464190792*VQ12A2*VQ1 4A2*VQ17A2*VQ19A2*VQ21A3*VQ24A3*VQ28 ATHESE PARTS ARE INCLUDED IN CARTRIDGE KITMODEL DESIGNATIONSCREW (4 REQ D)(TORQUE TO65-75 LB. FT)COVER2*VQ*A/C-(*)**-20(*)2*VQ*B/D-(*) **-20(*)3*VQ*A/C-(*)**-20(*)3*VQ*B/D-(*) **-20(*)96168119805224309242215224526242 214 NOTEBRONZE FACES MUSTBE INSTALLED TOWARDTHE ROTOR.
2 INCLUDED IN SINGLESHAFT SEAL KIT 920021F3 EQUIVALENT 920023 INCLUDED IN DOUBLESHAFT SEAL KIT 920022F3 EQUIVALENT 920024 INCLUDED INCARTRIDGE KIT WIPE OF SEAL WITH OILBEFORE PRESSING INTO GREASE TO SEAL INSTALLATION OF SHAFT. TO REVERSE CATRIDGE KIT ROTATION,REMOVE THE TWO (2) 413834 SCREWS,AND REVERSE THE LOCATION OF THEINLET SUPPORT PLATE 430805 ANDOUTLET SUPPORT PLATE THE TWO (2) SCREWS HANDTIGHT. USE PUMP COVER TO ALIGN ALLSECTIONS OF THE CARTRIDGE. REMOVECOVER CAREFULLY AND TIGHTENSCREWS TO 50 LB. IN. TORQUE. 154095 O-RING WARNING: USE THIS FOR PARTS INFORMATION ONLY.
3 SEE OVERHAUL MANUAL I-3144-S FOR MAINTENANCE INFORMATION. Eaton Hydraulics, Incorporated 2000 All Rights ReservedLHRHLHRHLHRHLHRHSHARP EDGE OF VANE MUSTLEAD DIRECTION OF ROTATION COVER ROTATION COVER ROTATION ASSEMBLE SEAL WITH SPRINGLOADED SEALING MEMBERTOWARD BEARING. ASSEMBLE SEAL FLUSH WITHPILOT FACE WITH SPRING LOADEDSEALING MEMBER FACING INWARDAS ASSEMBLY**VQ**F-**-20(L)INCLUDED INMOUNTING KITFB-B-10 SCREW(2 REQ D)205533 MOUNTINGBRACKET199491 BODY S/A942353942378942354942378 MODEL2*VQA/D-**-202*VQB/C-**-203*VQA/D-* *-203*VQB/C-**-20 SHAFTSSINGLE SEALMODELSDOUBLE 8623875524274724276723892947882699551617 1617341818755 STRAIGHT, KEYEDKEYED WITH NUTKEYED SHAFTSPLINESTRAIGHT, KEYED, HEAVY DUTYTYPE DUTYSTANDARDHEAVY DUTYSTANDARDHEAVY DUTYBEARING17052327501705232750 MODEL25VQ26VQ30VQ31VQ 419673 RING SEALING(ASSEMBLY NOTE.)
4 INSTALL INBODY BEFORE INSTALLATIONOF CARTRIDGE KIT.) 154078 O RING 588507 BACK-IP RING191400 SNAP RING120128 SNAP RING 429283 SHAFT SEAL (USE ON S FLANGE MOUNTED MODELS ONLY) 394976 SHAFT SEAL190362 WASHERKEY (SEE TABLE)KEY (SEE TABLE)NUT (SEE TABLE)SCREW (SEE TABLE)Model Code12345671 Viton Seals2 Series3 Vane Type4 SAE Rated Capacity5 Port Connections6 Mounting & Shaft SealsAssembly7 Shafts89108910 Port PositionsDesignRotation(Omit if not required.)25, 26, 30, 31(Rating @ 1200 RPM - 100 psi)See Capacity (USgpm)See Table InsideCodeInletOutletConnectionConnectio nASAE 4-BoltSAE 4-BoltBSAE Str.
5 Str. 4-BoltSAE Str. Str. 4-BoltF - Foot ( Single Shaft Seal Assy.)S - Flange (Double Shaft Seal Assy.)Omitted- Flange ( Single Shaft Seal Assy.)See Table InsideSee Chart Below(Viewed from Shaft End)L - Left Hand (CCW Rotation)Omitted - Right Hand RotationFor satisfactory service life of these components, use full flow filtration to provide fluid which meets ISO cleanliness code18/16/13 or cleaner. Selections from pressure, return, and in-line filter series are COVER POSITIONS (VIEWED FROM COVER END)**VQ**A-**A-20(L)**VQ**A-**B-20(L)** VQ**A-**C-20(L)**VQ**A-**D-20(L)OPPOSITE OUTLET PORT90 CLOCKWISE FROM OUTLETIN-LINE WITH OUTLET90 COUNTERCLOCKWISE FROM OUTLETCOVER (INLET)BODY(OUTLET)PARTS ORDERINGPARTS ARE THE SAME FOR BOTH RIGHT AND LEFT HAND ROTATION, WHEN ORDERINGSPARE CARTRIDGE PARTS, IT IS RECOMMENDED THEY BE OBTAINED IN CARTRIDGEKITS.
6 KITS ARE ASSEMBLED AND TESTED FOR EITHER RIGHT OR LEFT HAND LEFT HAND ROTATION IS REQUIRED, IT SHOULD BE SPECIFIED ON PARTS ORDER BYADDING SUFFIX L TO KIT NUMBER. FOR EXAMPLE, in
