Vickers Vane Pumps - Eaton

1 Service DataThru DriveVane Type Pump(F3)-45VT*(M)-**A(M)2-**-*-22I-3151- SRev 2/98 Vickers Vane Pumps45 VTA45 VTB45 VTBP45 VTCF3 SEAL KIT92020292020402-136932920206J 298147 Bolt (4 Req d)Torque (40 50 lb. ft. )353409 O Ring87947 Bolt (4 Req d)Torque 344 371 (255 275 lb. ft. )02 136718 Vane Kit(Includes12 vanes & inserts)Ring (See Table)578903 Inlet Plate S/A289476 Screw (2 Req d)Housing (See Table)220888 Pin (2 Req d)578900 RotorFFFR etaining Ring (See Table)Coupling (see Table)J A Adapter Plate (See Table)J 154086 O RingJ 351776 O Ring92020192020302-136931920205 MODELSEAL KITSPACERKITVTAVTBVTBPVTC584936584922941 29694129702-136817 MODELADAPTERPLATEADAPTERKITCOUPLINGRETAI NINGRINGCOUPLINGKIT581833941298223172830 03 (1)83003 (2)10398942677058492402-13681002-1368130 2-13681402-136816 NOTEFOR BP MODELS AN ADAPTER KIT AND SPACER KIT IS C Adapter Plate (See Table)435714 O RingJ 582519 Washer (4 Req d)J 298148 Bolt (4 Req d)Torque (40 50 lb.)

2 Ft. )J 298147 Bolt (4 Req d)Torque (40 50 lb. ft. )J B Adapter Plate (See Table)J 154088 O Ring588725 Spacer (See table) (BP models only)375422 O Ring (BP models only)427700 Washer (BP models only)205436 Screw (2 Req d) (BP models only)Included in seal kit (See Table)FIncluded in cartridge kit (See Table)Included in coupling kit (See Table)JIncluded in adapter kit (See Table)Included in spacer kit (BP models only)F3 equivalent seal kit (See Table)585658 Parts prefixed with symbols availableonly in Eaton Hydraulics, Incorporated 2000 All Rights Reserved45VT4245VT4545VT5045VT6058167958 257058168057890402 10257202 10257302 10257402 10257502 10257602 10259302 10257702 10257802-13692502-13692602-13692302-1369 2425228347850725228347850745VT*M**A45VT* M**AM45VT*S**A45VT*S**AMBODY S/AKey (See Table)For satisfactory service life of thesecomponents in industrial applications,use full flow filtration to provide fluidwhich meets ISO cleanliness code16/13 or cleaner.

3 OFP, OFR, and OFRS series filters are S/A (See Table)154107 O RingV 394974 Shaft Seal194878 WasherShaft (See Table)131812 Bearing102949 Retaining Ring158630 Retaining Ring154087 O Ring588509 RingFFF580921 Outlet PlateF5024185024758832775024195024808832 80502467883274883283 MODELSHAFTKEYMODELHOUSINGF CART KIT MODELRINGF3 CART KIT45 VTAS *20345 VTAS *29745 VTAM *292N45 VTB(P)S *20345 VTB(P)S *29745 VTB(P)M *292N45 VTCS *20345 VTCS *29745 VTCM *292N47230323975123975147230323975147230 3419675 Seal Ring(Install into body, theninstall catrtidge kit) 1113 Screw (4 Req d)Torque 102-115 (75-85 )502370 Flange (ISO 45VT*M only)(Included in 45VT*M Body S/A)(Included in 45VT*M Body S/A)V Assemble seal with spring loadedsealing member towards bearing. Sealsto be completely wetted with oil priorto Code123456 7 8 910 118To reverse cartridge kit rotation, removethe two screws and reverse the location ofthe inlet support plate and outlet supportplate.

4 Re install the two screws hand pump cover to align all sections of thecartridge. Carefully remove the cover andtighten the screws. Sharp Edges of Vane Must Lead in Direction of RotationWhen ordering spare cartridge parts, it isrecommended they be obtained in car-tridge kits. Kits are assembled and testedby Vickers for either right or left hand rota-tion. If left hand rotation is required, itshould be specified on parts order by add-ing suffix L to cartridge kit sealsThru drive series designation45VT 138 to 193 cm3/r( to in3/r)Rear pump mounting SAEM ISO 3019/2 100A2 HWS SAE J744 flangePilot designation(Rated capacity (USgpm) at1200 rpm, bar (100 psi)Codecm3/r in3 connectionsA SAE 4 bolt flangeM Metric thread port connection(4 bolt flange)Omit Inch thread port connection(4 bolt flange)Port connection modifier2 Coupling (included with pump)PumpTail shaft pumpseriesrequirementsThru drive couplingShaftOutlet positions(Viewed from adapter end of pump)A Opposite inlet portB 90_ CCW from inletC In line with inletD 90_ CW from inletDesignRotation(Viewed from shaft end of pump))

5 L Left hand for counterclockwiseR Right hand for clockwise1213 Omit Standard seals(ISO 3019/1) 2 bolt4 Geometric displacementFrameSize45VT45 VTASAE A size w/30_involute spline,9T 16/32 B size w/30_involute spline,13T 16/32 drive adapter orientation(Viewed from adapter end of pump)A adapterA Rotate 45_ CW with respectto pump mounting flangeB Rotate 45_ CCW with respectto pump mounting flangeB or C adapterA In line with pump mounting flangeB Rotate 90_ with respect to pumpmounting flange45 VTCSAE C size w/30_involute spline,14T 12/24 Heavy duty square key292N ISO key 8mm x 12mm (M pilot only)297 14T 12/24 splined SAE C A 2-bolt SAE A B 2-bolt SAE B BP 2-bolt SAE B to mountPVE12/19/21 (Includes spacer)C 2-bolt SAE C LHRHLHRHLHRHLHRHNOTENOTEForm No. 00-000 Copyright Eaton Corporation, 0000 All rights in Hydraulics15151 Highway 5 Eden Prairie, MN 55344 Telephone: 612 937-7254 Fax: 612 New Lane, HavantHampshire PO9 2 NBEnglandTelephone: (44) 170-548-6451 Fax: (44) 170-548-7110