Lecture 12: Photodiode detectors
The bandgap for direct absorption in silicon is 4.10 eV, corresponding to a threshold of 0.3 m. Germanium is another semiconductor material for which the lowest energy absorption takes place by indirect optical transitions. Indirect absorption will occur up to a threshold of 1.85 m.
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Standard Test Methods for DC Resistance or …
www-eng.lbl.govDesignation: D257 – 07 An American National Standard Standard Test Methods for DC Resistance or Conductance of Insulating Materials1 This standard is issued under the fixed designation D257; the number immediately following …
Resistance, Insulating, Conductance, For dc resistance or, For dc resistance or conductance of insulating
Raphael NXT User Guide - www-eng.lbl.gov
www-eng.lbl.govRaphael NXT can extract capacitance of nets in large designs to better than 1% accurate. Raphael NXT ca n be used by itself (standalone mode)
Raphael Reference Manual - www-eng.lbl.gov
www-eng.lbl.govRaphaelTM Interconnect Analysis Program Reference Manual Version Y-2006.03, March 2006
Heat and Mass Transfer
www-eng.lbl.govHeat transfer through walls made of layers of di fferent types of materials can be easily found by summing the resistances in series or parallel form, as appropriate. In the design of systems, seldom is a surface temperature specified or known.
Guidelines for the CONTROL OF STATIC ELECTRICITY IN …
www-eng.lbl.govGUIDELINES FOR THE CONTROL OF STATIC ELECTRICITY IN INDUSTRY 4 ARCHIVE 1. INTRODUCTION 1.1 Static electricity is generated by the contact and separation of materials, and clearly this generation often cannot be prevented in the industrial setting.
ISO metric screw threads
www-eng.lbl.govBS 4827, ISO miniature screw threads. BS 5346, ISO metric trapezoidal screw threads. 3 Basic profile 3.1 General. This clause specifies the basic profile for ISO general purpose metric screw threads as shown in Figure 1. The dimensions for the various standard pitches are given in Table 1.
Vacuum Technology and Vacuum Design Handbook for ...
www-eng.lbl.gov• Tack (stitch) welding is recommended on the external side only with less than 50% of the diameter covered in small intervals. This minimises the chance of trapped voids and facilitates He leak testing post welding. • All welds must be free from pitting and scale. Must be cleaned to bare metal. If chemicals
UNITS CONVERSION TABLES
www-eng.lbl.govThese conversion tables are provided for your reference. Units Conversion Tables Table 1 Multiples and Submultiples of SI Units Table 2 Length Units Table 3 Area Units Table 4 Volume Units Table 5 Mass Units Table 6 Density Units Table 7 Volumetric Liquid Flow Units Table 8 Volumetric Gas Flow Units ...
ASSOCIATION CONNECTING ELECTRONICS INDUSTRIES IPC …
www-eng.lbl.govIPC-2221A Generic Standard on Printed Board Design ASSOCIATION CONNECTING ELECTRONICS INDUSTRIES® 2215 Sanders Road, Northbrook, IL 60062-6135 Tel. 847.509.9700 Fax 847.509.9798 www.ipc.org IPC-2221A May 2003 A standard developed by IPC Supersedes IPC-2221 February 1998
Pilot-operated safety relief valves: A simple, effective ...
www-eng.lbl.govThe replacement of direct spring-operated pressure relief valves (PRVs) with pilot-operated safety relief valves (POSRVs) can help plant operators streamline maintenance processes, reduce maintenance costs, address common valve performance issues, maintain safety and potentially increase output.
Related documents
The Bandgap Reference - University of California, Los Angeles
www.seas.ucla.eduLow-Voltage Bandgap References The basic bandgap expression, VV BE +17.,2 T takes on a value of about 1.25 V at T = 300K, defying direct implementation in today’s low-voltage technologies. We describe one low-voltage example and refer the reader to [10] and [11] for others. For a low-voltage bandgap reference to have a zero TC, it must produce an
Metal/Semiconductor Ohmic Contacts - Stanford University
web.stanford.eduBandgap Engineering Contact resistance depends on barrier height. It is possible to use a lower bandgap material in the source/drain such as Si1-xGex. Band gap of Si1-xGex reduces as compared to Si as Ge fraction increases. • Si1-xGex S/D & germanosilicide contact − Assuming metal Fermi level is pinned near midgap
LOW DROPOUT LINEAR REGULATOR - Diodes Incorporated
www.diodes.comIts circuit includes a trimmed bandgap reference to assure output voltage accuracy to be within ±1%. On-chip thermal shutdown provides protection against a combination of high current and ambient temperature that would create excessive junction temperature. The AZ1117C is available in 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5.0V fixed ...
Description Pin Assignments - Diodes Incorporated
www.diodes.comThe AP7361C is available in U-DFN3030-8 (Type E), SOT89-5, SOT223, TO252 (DPAK) and SO-8EP packages. Features • Wide Input Voltage Range: 2.2V to 6.0V