1967-1968 Camaro - Classic Instruments
Our installation instructions and procedures should take priority over instructions furnished by any other manufactures of ignition systems, wiring harnesses, gauges, etc. TECHNICAL ASSISTANCE . 1-800-575-0461 . ... The fuel level gauge in your instrument cluster is designed to
Download 1967-1968 Camaro - Classic Instruments
Information
Domain:
Source:
Link to this page:
Documents from same domain
70-72 Chevelle Installation Manual Rev 091313
www.classicinstruments.comcomponents mounted in the dash panel or that are preventing the dash panel from being removed. See the below list as a guideline for connections to be removed: a. Cigarette lighter b. Blower motor c. Stereo d. Dash lights e. Glove box light f. Radio antenna g. Headlight switch 10) Remove the dash panel from the vehicle. 11) Remove the headlight ...
1967-1972 Chevy Truck Installation Manual
www.classicinstruments.comJun 18, 2002 · connection for the sender ground. 4) Connect a wire from the top terminal of the oil pressure sender to the Blue wire of the gauge wire harness. Temperature Sender Installation (Part No. SN22, SN23, SN24 & SN25) 1) Disconnect battery before making any connections. 2) Install the Classic Instrument’s temperature sending
1957 Chevy Installation Manual Revision 010615
www.classicinstruments.comJun 15, 2001 · For all other ignition systems please look at the owner’s manual for that system. 7) Connect the oil pressure sender to the BLUE wire of the gauge cluster wire harness. 8) Connect high beam indicator power to the GREEN wire of the gauge cluster wire harness. 9) Connect dash light power to the GREY wire of the gauge cluster wire harness.
Amp Gauge Wiring - Classic Instruments
www.classicinstruments.comAmp Gauge Wiring 1) Always disconnect the ground lead from the vehicle battery before wiring any gauge. 2) Classic Instruments’ Amp gauge should only be used on vehicles with alternators rated at 60 Amps or less. Using an alternator with higher output capacity is dangerous and could cause a fire. A Volt gauge
Related documents
Owner’s Manual - American Honda Motor Company
cdn.powerequipment.honda.comMake sure that any spilled fuel has been wiped up before starting the engine. 31Z376010.book 8 ページ 2013年11月6日 水曜日 午後4時23分
GT 18HP TWiN 44 MO WER GARDEN TRACTOR - Sears Parts …
c.searspartsdirect.comMower Drive Belt Installation Blade.: Sharpening Replacement Brake Adjustment Filter, Air 17 Fuel: Type 12 Storage 26 Fuse 23 G Gauge Wheels 13 H Hood Removal 23 C Carburetor Adjustment Clutch,_ Electric, Adjustment Controls, Tractor Cutting Level, Mower Engine:' Air Screen Oil Change Off Level Oil Type Starting Storage E Lubrication,: Chart 18 ...
Gauge Sets - American Honda Motor Company
cdn.powerequipment.honda.comCoolant temperature, fuel rate, fuel used, fuel level, trim, battery voltage, engine hours, and vessel speed*. * Requires NMEA 2000 GPS input to backbone. Use of …
A10VO - Robert Bosch GmbH
dc-ca.resource.bosch.com9 Test Equipment: Gauge Test Port Kit 10 10 Port Sizes 11 11 Optional Accessories – Low Oil Shut-Off Block 11 12 Unit Dimensions 12 12.1 A10VO71 12 12.2 A10VO45 14 12.3 A10VO28 16 12.4 A10VO71, 45, 28 18 12.5 A10VO45 Series 50 19 13 Standard Models Used 20 14 Standard Spare Parts 20 14.1 Replacement Pump Control Valve 20
Installation and Setup Guide - Lennox
resources.lennox.cominstallation uses 18 GAUGE thermostat wire or larger, thermostat wire run length DOES NOT EXCEED 300' (91m), load from any thermostat connection is 1 AMP or LESS. WARNING Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury or loss of life. Installation and service must be performed by a
IMPORTANT SAFETY INSTRUCTIONS - Battery Tender
www.batterytender.comto carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gage metal part of the frame or engine block. g) When disconnecting charger, turn switches to off, disconnect AC cord, remove clip from vehicle chassis, and then remove clip from battery terminal. h) See operating instructions for length of charge information.
1957 Chevy Installation Manual Revision 010615
www.classicinstruments.comJun 15, 2001 · gauge. Fuel Gauge Wiring Diagram Ground +12VDC switched Dash Light Power O G L S I Signal Wire Fuel Level Sender Ground Pulse Signal Generator [SN16] Wiring Attach the signal generator to the transmission speedometer gear housing (where the speedometer cable originally connected). Do not use excessive force to tighten. These signal generators ...
HELP?: GENERAL APPLICATION: Installation Instructions ...
www.stewartwarner.comFUEL LEVEL GAUGE WIRING (Figure 4): 1. Disconnect negative (-) battery cable. 2. Using 18-ga. wire, connect the (G) terminal to a clean (rust/paint-free) Figure 4ground. 3. Using 18 gauge wire, connect the (I) terminal to a switched +12V source. 4. Using 18-gauge wire, connect the (S) sender terminal of the gauge to the fuel level sender. 5.